Benutzeranleitung / Produktwartung RX-889PGD des Produzenten JVC
Zur Seite of 56
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference.
W arnings, Cautions and Other s / A visos, precauciones y otras notas / Advertêcias, precauções e outras notas / G-1 CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture.
G-2 English Caution: Proper V entilation T o av oide r isk of electric shock and fire and to protect from damage. Locate the apparatus as follo ws: F ront: No obstructions open spacing. Sides: No obstructions in 10 cm from the sides. T op: No obstructions in 10 cm from the top.
1 English T able of Contents Using the DSP Modes ................................ 20 A v ailable DSP Modes According to the Speaker Arrangement .. 22 Adjusting the 3D-PHONIC Modes .......................................... 23 Adjusting the D AP Modes .
2 English Par ts Identification Become familiar with the buttons and controls on the receiver before use. Refer to the pages in parentheses for details.
3 English ANTENNA AM EXT AM LOOP FM 75 COAXIAL A M L O O P AN TENNA A M E X T F M 7 5 C O A X I A L A M L O O P AN TENNA A M E X T F M 7 5 C O A X I A L Getting Star ted This section explains how to connect audio/video components and speakers to the receiver , and how to connect the power supply .
4 English Basic connecting procedur e 1 Cut, twist and remove the insulation a t the end of each speaker signal cable (not supplied). 2 T urn the knob counter c loc kwise.
5 English Connecting the subwoofer speaker Y ou can enhance the bass by connecting a subwoofer . Connect the input jack of a powered subw oofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs (not supplied).
6 English IMPORT ANT : This receiv er is equipped with both the composite video and S-video input/output terminals for connecting video components. Y ou do not have to connect both the composite video and S-video terminals.
7 English DVD player • When you connect the D VD player with stereo output jacks: DVD player Å To front left/right channel audio output (or to audio mixed output if necessary) ı To S-video output .
8 English Digital connections This receiv er is equipped with three DIGIT AL IN terminals — one digital coaxial terminal and two digital optical terminals. Y ou can connect any component to an y one of the digital terminals using the digital coaxial cable (not supplied) or digital optical cable (not supplied).
9 English Basic Operations The following operations are commonly used when you play any sound source. IMPORT ANT : When using the remote control, check to see if its remote control mode selector is set to the correct position: T o operate an audio system, TV , and VCR, set it to “A UDIO/TV/VCR.
10 English When playing a digital source thr ough a digital terminal • The DIGIT AL SOURCE FORMA T lamps on the front panel indicate what type of the digital signal comes into the recei ver . MPEG : Lights up when MPEG Multichannel signals (see page 21) come in.
11 English Listening only with headphones 1. Connect a pair of headphones to the PHONES jack on the front panel . 2. Pr ess SPEAKERS 1 and/or 2 so tha t no lamps on the buttons ar e turned on. CAUTION: Be sure to turn down the volume bef ore connecting or putting on headphones, as high v olume can damage both the headphones and your hearing.
12 English Basic Settings Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier .
13 English SETTING SOURCE SELECTOR INPUT ANALOG/DIGITAL Digital Input (DIGIT AL IN) T erminal Setting When you use the digital input terminals, you ha ve to register what components are connected to which terminals (DIGIT AL IN 1/2/3). Bef ore you start, r emember .
14 English Center Delay T ime Setting Register the delay time of the sound from the center speak er, comparing that of the sound from the front speakers. If the distance from your listening point to the center speaker is equal to that to the front speakers, select 0 msec.
15 English 80Hz 100Hz 120Hz 2. T urn MUL TI JOG to select the low fr equency effect attenuator level. • As you turn it, the display changes to show the follo wing: 0dB: Normally select this. 10dB: Select this when the bass sound is distorted. Note: Low frequency eff ect attenuator setting is not valid f or the D VD MUL TI playbac k mode.
16 English Storing the Basic Settings and Adjustments — One T ouch Operation JVC’ s One T ouch Operation function is used to assign and store dif fer ent sound settings for each different playing source. By using this function, you do not hav e to change the settings every time you change the source.
17 English Receiving Radio Broadcasts Y ou can browse through all the stations or use the preset function to go immediately to a particular station. Using Preset T uning Once a station is assigned to a channel number , the station can be quickly tuned.
18 English T o tune in a preset station On the front panel: 1. T urn SOURCE SELECT OR to select the band (FM or AM). The last recei ved station of the selected band is tuned in. 2. Press TUNER PRESET . 3. T urn MUL TI JOG until y ou find the channel y ou want.
19 English Using the SEA Modes The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds. IMPORT ANT : When using the remote control, check to see if its remote control mode.
20 English 3D-PHONIC modes The 3D-PHONIC mode gi ves you such a nearly surround effect as it is reproduced through the Dolby Surround decoder , which is widely used to reproduce sounds with a feeling of movement lik e those experienced in mo vie theaters.
21 English Surr ound modes W ith this receiver , you can use four types of the Surround mode. Follo wing modes cannot be used when only the front speakers are connected to this r eceiver (without the r ear speakers or center speaker).
22 English Available DSP Modes According to the Speaker Ar rangement A v ailable DSP modes will vary depending on ho w many speakers are used with this recei ver .
23 English IMPORT ANT : When using the remote control, check to see if its remote control mode selector is set to the correct position: T o operate this receiver , set it to “A UDIO/TV/ VCR” (except when selecting the DBS tuner as the source).
24 English 3. Adjust the effect level. 1) Press B ALANCE/SURROUND ADJUST repeatedl y until “DSP EFFECT” appears on the display . The display changes to sho w the current setting.
25 English Notes: • Y ou can adjust the speaker output le vels without outputting the test tone. • No test tone comes out of the center speaker when “CENTER SPK” is set to “NONE” (see page 14). • No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 14).
26 English JVC Theater Surr ound adjustments Bef ore you start, r emember ... • Make sur e that you hav e set the speaker information corr ectly (see page 14). • There is a time limit in doing the following ste ps. If the setting is canceled before you f inish, start fr om step 1 again.
27 English On the front panel: Y ou can also use the b uttons on the front panel to adjust the Surround modes. Howe ver , no test tone is av ailable when using the buttons on the front panel. So, mak e adjustments while listening to the sound of the source played back.
28 English For the other DSP modes On the front panel: 1. Press DSP MODE repeatedl y until the mode y ou want appears on the display . • Each time you press the button, the DSP modes change. (See page 22 for more details.) 2. Select and play a sound source.
29 English Using the DVD MUL TI Playback Mode This receiver provides the DVD MUL TI playback mode for r epr oducing the analog discrete output mode of the DVD player . Before playing back a DVD, refer also to the manual supplied with the DVD player . 4.
30 English Fr om the r emote contr ol: 1. Press D VD MUL TI so that “D VD MUL TI” appears on the display . Note: When you select “D VD MUL TI” as the source to play , the DSP mode is canceled temporarily , and the SURROUND ON/OFF and SURROUND MODE b uttons do not work.
31 English MAIN MENU SOURCE : ch 1 FM 87.50 MHz VISUAL :VCR1 MODE :OFF SOUND CONTROL TUNER CONTROL SETTING VOLUME : 20 :OPERATE Using the On-Scr een Menus Y ou can use the Menus on the TV screen to control the receiver .
32 English Listening at Low Volume (Loudness) (Also see page 11) 1. Press MENU . The MAIN MENU appears on the TV . • Pressing one of the % / fi / @ / # b uttons also displays the MAIN MENU. 2. Press % / fi to move to “SOUND CONTR OL, ” then press @ / # .
33 English 6. Press % / fi to move to the item you want to set or adjust, then press @ / # . On this adjustment menu, you can do the following: “CENTER LEVEL”: Adjust the center speaker output le vel. “REAR L LEVEL”: Adjust the left rear speaker output le vel.
34 English SEA ADJUST SEA USERMODE SET :MEMORY 100 10kHz 1k 4. Press % / fi to move to “SEA ADJUST . ” The SEA ADJUST menu appears. 5. Press % / fi / @ / # to adjust the SEA mode as y ou want. @ / # : Select the frequency ranges. % / fi : Adjust the frequency le vels.
35 English 6. Press % / fi to move to “PRESET NAME, ” then press SET . The character entry screen appears. 7. Press % / fi / @ / # to move in front of a character y ou want. Y ou can also select the follo wing: : T o enter space : T o erase the character : T o go back to the previous character position or go to the next character position 8.
36 English COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver .
37 English TEXT COMPU LINK 1(MASTER UNIT) 2(SLAVE UNIT) COMPU LINK – 3 (SYNCHRO) TEXT COMPU LINK Remote Contr ol System The TEXT COMPU LINK remote control system has been newly developed to deal with the disc information recorded in the CD T ext* and MDs.
38 English On-Screen Operation buttons (on the remote control) 1 Source name: CD or MD 2 Select or , then press SET to change the disc. 3 T rack numbers and track titles. • The current playing (selected) track is indicated in yello w . • When you mo ve to a track number, y ou can change the track information by pressing @ / # .
39 English Sear ch for a disc by its disc title: 1. Press TEXT DISPLA Y while “CD” is selected as the source. The Disc Information screen appears on the TV . 2. Press % / fi to move to “SEARCH, ” then press SET . The DISC SEARCH screen appears.
40 English Sear ch for a disc by its genr e: 1. Press TEXT DISPLA Y while “CD” is selected as the sour ce . The Disc Information screen appears on the TV . 2. Press % / fi to move to “SEARCH, ” then press SET . The DISC SEARCH screen appears.
41 English For the MD recor der: Y ou can write the disc information (disc title and song titles) into the disc. Y ou can only write the song title for the song currently selected.
42 English Operating JVC’ s Audio/V ideo Components Y ou can operate JVC’ s audio and video components with this receiver’ s remote control, since control signals for JVC components are preset in the remote control.
43 English T urntable After pressing PHONO (with the remote control mode selector set to “ A UDIO/TV/VCR”), you can perform the f ollowing oper ations on a turntable: PLA Y : Starts playing.
44 English Operating Other Manufacturers’ V ideo Equipment This remote control supplied with the recei ver can transmit control signals for other manufacturers’ VCRs, TVs, CA TV con verters and DBS tuners.
45 English T o change the transmittable signals for operating another manufacturer’s VCR 1. Set the remote control mode to “ A UDIO/TV/ VCR. ” 2. Press and hold VCR 1 . 3. Press VCR 1. 4. Enter manuf acturer’ s code (thr ee digits) using buttons 1 – 9, and 0.
46 English Manufacturers’ codes for TV A -Mark 003 Acura 009 Admiral 093 Aiko 092 Akai 030, 208 Akura 264 Alaron 216 Alba 009, 036, 037 Amstrad 009, 037 Anam 003, 004, 009, 068, 161, 250, 425, 426 A.
47 English Simpson 186 Sky-Worth 037 Sonitron 208 Sonoko 009, 037 Sonolor 208 Sontec 037 Sony 000, 036 Soundesign 178, 186 Soundwave 037 Spectricon 003 Standard 009 SuperTech 216 Supreme 000 Sylvania .
48 English Manufacturers’ codes for CATV converters ABC 008 Daeryung 008 GoldStar 838 LG Alps 779 Memorex 000 Now 776 Panasonic 000 Paragon 000 Pulsar 000 Quasar 000 Runco 000 Samsung 702 Scientific.
49 English Melectronic 038 Memorex 000, 037, 046, 048, 104, 162, 240 Memphis 072 Metz 037, 162, 195, 227 MGA 043, 061, 240 MGN Technology 240 Minerva 195 Minolta 042 Mitsubishi 043, 048, 061, 067, 081.
50 English T r oubleshooting Use this char t to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC ser vice center . PROBLEM The display does not light up. No sound from speakers. Sound from one speaker only.
51 English Specifications Amplifier Output Power At Stereo operation: Front channels: 100 watts per channel, min. RMS, dri ven into 8 ohms, 1 kHz with no more than 0.8% total harmonic distortion. (IEC268-3/DIN) At Surround operation: Front channels: 70 watts per channel, min.
52 English FM tuner (IHF) T uning Range: 87.50 MHz to 108.00 MHz Usable Sensiti vity: Monaural: 12.8 dBf (1.2 µV/75 ohms) 50 dB Quieting Sensitivity: Monaural: 21.
EN, SP, CH J V C 0499HIMMDWJEM Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia and U.K.) Instrucción sobre la línea de la red (CA) (no aplicable para Europa, EE.UU., Canadá, Australia, ni el Reino Unido) Instrução sobre a tensão da rede eléctrica (CA) (não aplicável para a Europa, os E.
Ein wichtiger Punkt beim Kauf des Geräts JVC RX-889PGD (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JVC RX-889PGD noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JVC RX-889PGD - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JVC RX-889PGD reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JVC RX-889PGD erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JVC RX-889PGD besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JVC RX-889PGD verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JVC RX-889PGD. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JVC RX-889PGD gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
