Benutzeranleitung / Produktwartung RX-7022VSL des Produzenten JVC
Zur Seite of 46
INSTR UCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference.
W arnings, Cautions and Others Caution –– switch! Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc.
G-2 Wall or obstructions RX-7022VSL Floor Spacing 15 cm or more Front Stand height 15 cm or more Caution: Proper V entilation T o a void risk of electric shock and fire and to protect from damage . Locate the apparatus as f ollows: F ront: No obstructions open spacing.
1 T able of Contents Par ts Identification ...................................... 2 Getting Star ted ........................................... 3 Before Installation ...................................................................... 3 Checking the Supplied Accessories .
2 Par ts Identification Front Panel Remote Contr ol Front Panel 1 ST ANDBY/ON button and ST ANDBY lamp (10) 2 FM/AM TUNING 5 / ∞ buttons (21) 3 FM/AM PRESET 5 / ∞ buttons (21, 22) 4 FM MODE button.
3 Before Installation General Pr ecautions • DO NO T insert any metal object into the unit. • DO NO T disassemble the unit or remove scr ews, cov ers, or cabinet. • DO NO T expose the unit to rain or moisture. Locations • Install the unit in a location that is lev el and protected from moisture.
4 DIGITAL 1 ( DVD ) DIGITAL 2 ( CD ) DIGITAL 3 ( TV ) DIGITAL 4 ( CDR ) DOLBY DIGITAL/PCM /DTS DOLBY DIGITAL / PCM / DTS FRONT CENTER DVD DBS FM 75 COA XIA L COMPU LINK-4 (SYNCHRO) MONITOR OUT ANTENNA.
5 Connecting speakers to the FRONT SPEAKERS 1 terminals For each speaker , connect the (+) and ( – ) terminals on the rear panel to the (+) and ( – ) terminals marked on the speak ers. 1 Cut, twist and remo ve the insulation at the end of each speaker signal cable (not supplied).
6 AUDIO TV SOUND DBS VCR OUT (REC) IN (PLAY) TAPE CDR CD PHONO OUT (REC) IN (PLAY) RIGHT LEFT Left rear speaker Right rear speaker CENTER SPEAKER REAR SPEAKERS RIGHT LEFT + – Center speaker Connecting the rear and center speakers Connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals.
7 CD player V ideo component connections Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack.
8 TV and/or DBS tuner DVD player • When you connect the D VD player with stereo output jacks: Å To front left/right channel audio output ı To composite video output Ç To S-video output Î To component video output • When you connect the D VD player with its analog discrete output (5.
9 DIGIT AL 2 ( CD ) DIGIT AL 3 ( TV ) DIGIT AL 4 (CDR) DIGIT AL 1 (DVD) DIGIT AL IN DVD DBS DOLBY DIGITAL /PCM /DTS Notes: • When shipped from the f actor y , the DIGIT AL IN terminals hav e been se.
10 Front Panel Remote Control T urning On the Power Press ST ANDBY/ON (or A UDIO on the remote control). The ST ANDBY lamp goes of f. The name of the current source (or station frequency) appears on the display . T o turn off the po wer (into standby mode) Press ST ANDBY/ON (or AUDIO on the remote control) again.
11 Adjusting the V olume On the front panel: T o increase the volume, turn MASTER V OLUME clockwise. T o decrease the v olume, turn it counterclockwise. From the remote control: T o increase the volume, press V OLUME +. T o decrease the v olume, press VOLUME – .
12 Changing the Display Brightness Y ou can dim the display . Press DIMMER on the remote contr ol . • Each time you press the button, the display dims and brightens alternately . T urning Off the Power with the Sleep T imer Y ou can f all asleep while listening to music — Sleep Timer .
13 Basic adjustment auto memory This receiv er memorizes sound settings for each source when — : • you turn of f the power , • you change the source, and • you assign the source name. When you change the source, the memorized settings for the newly selected sour ce are automatically recalled.
14 Setting the Digital Input [DIGIT AL IN] T erminals When you use the digital input terminals, you ha ve to register what components are connected to which terminals (DIGIT AL IN 1/2/3/4). Bef ore y ou start, remember ... There is a time limit in doing the following ste ps.
15 Selecting the Analog or Digital Input Mode When you hav e connected digital source components using both the analog connections (see page 6) and the digital connections (see page 9) methods, you need to select the input mode correctly . Befor e you start, r emember .
16 Selecting the V ideo Input T er minal This receiv er is equipped with the component video input terminals for the D VD player and DBS tuner , which gi ve you higher picture quality . When you use the component video input terminals for the D VD player and/or DBS tuner , change the video input terminal setting.
17 Speaker size Register the sizes of all the connected speak ers. • When you change your speakers, reg ister the information about the speakers again. 1 Press SETTING r epeatedly until “ FRNT SP (Fr ont Speaker), ” “ CNTR SP (Center Speaker) ” or “ REAR SP (Rear Speaker) ” (with the curr ent setting)* appears on the display .
18 OFF MID MAX 2 Press CONTR OL UP 5 /DO WN ∞ to select the low fr equency effect attenuator lev el. • Each time you press the button, the setting alternates between “ 0dB ” and “– 10dB. ” 0dB : Normally select this. – 10dB : Select this when the bass sound is distorted.
19 Fr ont Panel Remote Control Once each of f ollowing settings has been adjusted, this receiv er memorizes the adjustment f or each source. Attenuating the Input Signal When the input le vel of the analog source is too high, the sounds will be distorted.
20 Adjusting the Subwoofer Output Level Y ou can adjust the subw oofer output lev el if you have connected a subwoofer and set the subwoofer information correctly —“ YES. ” On the front panel: Bef ore y ou start, remember ... There is a time limit in doing the follo wing steps.
21 T uner Operations Front Panel Remote Control CONTROL + − + − + − 23 1 56 4 89 7/P 0 +10 10 BASS BOOST EFFECT MENU ENTER TEST DIMMER MUTING CH TV VOL /REW FF/ VOLUME CATV/DBS CONTROL TV/VIDEO .
22 4 Press MEMOR Y again while the selected channel number is flashing on the display . The selected channel number stops flashing. The station is assigned to the selected channel number . 5 Repeat steps 1 to 4 until you stor e all the stations you want.
23 Cr eating Realistic Sound Fields ** Manuf actured underlicense from Digital Theater Systems, Inc. US P A T . No. 5,451,942 and other world-wide patents issued and pending. “ DTS ” and “ DTS Digital Surround ” are trademarks of Digital Theater Systems, Inc.
24 ■ All Channel Stereo This mode can reproduce a larger stereo sound f ield using all the connected (and acti vated) speakers. All Channel Stereo can be used when the fr ont and rear speakers are connected to this r eceiv er without respect to the center speaker connection.
25 About Relations between Speaker Layouts and Surround Modes A vailable Surround modes will v ary depending on how man y speakers are used with this receiver . Make sur e that you ha ve set the speaker inf ormation correctly (see pages 16 to 18). • If only front speaker s are connected, y ou cannot use Surround modes.
26 Bef ore y ou start, remember ... • Make sur e that you ha ve set the speaker inf ormation correctly (see pages 16 to 18). • Y ou cannot adjust the center speak er output level when y ou hav e set “ CNTR SP ” to “ NONE. ” • Y ou cannot adjust the rear speak er output lev els when you have set “ REAR SP ” to “ NONE.
27 3 Press SOUND . The 10 keys ar e activ ated for sound adjustments. 4 Press TEST to check if you can hear the sounds thr ough all the speakers at the equal le vel.
28 When you select “ PL II MUSIC, ” y ou can go to the f ollowing adjustment. 4 T ur n Panorama contr ol on or off. 1) Press ADJUST r epeatedly until “ P ANORAMA ” (with the current setting)* appears on the display . * “ OFF ” is the initial setting.
29 On the front panel: 1 Start playing 2 channel softwar e — either analog or Linear PCM — and select the source. 2 Press SURR OUND ON/OFF to activ ate Surround mode. When Surround mode turns on, the last selected Surround mode will be acti vated.
30 This receiv er provides the D VD MUL TI playback mode for reproducing the analog discrete output mode of the D VD player . Before playing back a D VD, refer also to the manual supplied with the D VD player .
31 COMPU LINK Remote Contr ol System Automatic Power On/Off (Standby): only possible with the COMPU LINK-3 and COMPU LINK-4 Both the CD player and cassette deck (or CD recorder) turn on and off (standby) along with the recei ver .
32 A V COMPU LINK Remote Control System The A V COMPU LINK remote control system allows you to operate JVC ’ s video components (TV , VCR, and D VD player) through the receiv er . This receiv er is equipped with the A V COMPU LINK-III, which added a function to operate JVC ’ s video components through the video components terminals.
33 One-T ouch DVD Play Simply by starting playback on the D VD player , you can enjoy the D VD playback without setting other switches manually . • When the D VD player is connected through the anal.
34 Operating JVC ’ s Audio/V ideo Components Y ou can use the r emote control to operate other JVC ’ s components. Operating Audio Components IMPORT ANT: T o operate JVC ’ s audio components usi.
35 CD player After pressing CD, you can use the following b uttons for CD operations: 3 3 3 3 3 : Start playback. 4 : Return to the beginning of the current (or previous) track. ¢ : Skip to the beginning of the next track. 7 7 7 7 7 : Stop playback. 8 8 8 8 8 : Pause playback.
36 Operating Video Components IMPORT ANT: T o operate JVC ’ s video components using this remote control: • Y ou need to connect JVC ’ s video components through the A V COMPU LINK terminals (see page 32) in addition to the connections using cables with RCA pin plugs (see pages 7 and 8).
37 Operating Other Manufactur ers ’ V ideo Equipment By changing the transmittable signals, y ou can use the remote control supplied f or this unit to operate other manufactur ers ’ equipment. • Refer also to the manuals supplied for the other products.
38 5 T ry to operate y our CA TV converter or DBS tuner by pr essing CA TV/DBS . When your CA TV conv erter or DBS tuner turns on or off, you hav e entered the correct codes. If ther e are more than one code listed f or your brand of CA TV con verter or DBS tuner, try each one until the correct one is entered.
39 23 1 56 4 89 7/P 0 +10 10 EFFECT TEST RETURN FM MODE 10 0 + – SUB WOOFER + – REAR • R + – REAR • L + – CENTER + MENU ENTER Manufacturers ’ codes f or VCR Manufacturer Codes JVC 00 * ,.
40 T roubleshooting Use this chart to help you solve daily operational problems. If there is an y problem you cannot solve, contact your JVC ’ s service center . SOLUTION Plug the power cord into an AC outlet. Check speaker wiring and reconnect if necessary.
41 Specifications Designs & specifications ar e subject to change without notice. Amplifier Output Po wer At Stereo operation: Front channels: 100 W per channel, min. RMS, Both channels dri ven into 8 Ω at 1 kHz, with no more than 0.9% total harmonic distortion.
42 FM tuner (IHF) T uning Range: 87.50 MHz to 108.00 MHz Usable Sensiti vity: Monaural: 17.0 dBf (1.95 µV/75 Ω ) 50 dB Quieting Sensitivity: Monaural: 21.3 dBf (3.2 µV/75 Ω ) Stereo: 41.3 dBf (31.5 µV/75 Ω ) Signal-to-Noise Ratio (IHF-A weighted): Monaural: 78 dB at 85 dBf Stereo: 73 dB at 85 dBf T otal Harmonic Distortion: Monaural: 0.
EN 0402NHMMDWJEIN J V C VICTOR COMP ANY OF JAP AN , LIMITED RX-7020V[A]_COVER2 02.4.9, 3:46 PM 2.
Ein wichtiger Punkt beim Kauf des Geräts JVC RX-7022VSL (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JVC RX-7022VSL noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JVC RX-7022VSL - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JVC RX-7022VSL reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JVC RX-7022VSL erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JVC RX-7022VSL besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JVC RX-7022VSL verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JVC RX-7022VSL. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JVC RX-7022VSL gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
