Benutzeranleitung / Produktwartung CS 2135T des Produzenten Jonsered
Zur Seite of 36
CS 2135T Operator’ s manual (EP A II) Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine .
2 – English KEY T O SYMBOLS Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ..........................................
4 – English INTR ODUCTION Dear customer! Cong ratulations on y our choice to buy a Jonsered product! Y our purchase gives y ou access to prof essional help with repairs and ser vice whenev er this ma y be necessar y .
English – 5 WHA T IS WHA T? What is what on the c hain saw? 1 Filter cov er 2 F ront handle 3 F ront hand guard 4 Star ter 5 Chain oil tank 6 Star ter handle 7 Adjuster screws carb uretor 8 Stop and.
6 – English GENERAL SAFETY PRECA UTIONS Bef ore using a new c hain saw • Please read this manual carefully . • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly . • Refuel and star t the chain saw .
English – 7 GENERAL SAFETY PRECA UTIONS chain sa w usage if possible . Y our dealer , f orestr y school or your libr ar y can provide inf or mation about which training materials and courses are av ailable. Work is constantly in progress to impro ve the design and technology - improv ements that increase your saf ety and efficiency .
8 – English GENERAL SAFETY PRECA UTIONS • This mov ement activates a spring-loaded mechanism that tightens the brak e band (C) around the engine dr iv e system (D) (clutch drum). • The front hand guard is not designed solely to activate the chain brak e.
English – 9 GENERAL SAFETY PRECA UTIONS Will m y inetria activated c hain brake alwa ys activ ate during kickbac k in the event of a kic kbac k? No . First y our brake must be in w orking order. Second the kickbac k must be strong enough to activ ate the chain brake .
10 – English GENERAL SAFETY PRECA UTIONS Muffler The muffler is designed to k eep noise lev els to a minimum and to direct e xhaust fumes awa y from the user .
English – 11 GENERAL SAFETY PRECA UTIONS Bar • Length (inches/cm) • Number of teeth on bar tip sprock et (T). • Chain pitch (inches). The spacing betw een the dr iv e links of the chain must match the spacing of the teeth on the bar tip sprock et and drive sprock et.
12 – English GENERAL SAFETY PRECA UTIONS Sharpening cutting teeth T o shar pen cutting teeth you will need a round file and a file gauge. See instr uctions under the heading T echnical data for inf or mation on the size of file and gauge that are recommended f or the chain fitted to your chain saw .
English – 13 GENERAL SAFETY PRECA UTIONS • Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner . Tighten the chain until it does not sag from the underside of the bar . • Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time.
14 – English GENERAL SAFETY PRECA UTIONS Chain drive sproc ket The clutch drum is fitted with one of the follo wing drive sprock ets: A Spur sprock et (the chain sprock et is welded on the drum) B Rim sprock et (replaceable) Regularly check the degree of wear on the driv e sprock et.
English – 15 ASSEMBL Y Fitting the bar and c hain Check that the chain br ake is in disengaged position by moving the front hand guard to wards the front handle. Remov e the bar nuts and remov e the clutch cov er (chain brak e). T ake off the transportation r ing (A).
16 – English FUEL HANDLING Fuel Note! The machine is equipped with a two-stroke engine and must alwa ys be run using a mixture of gasoline and two- stroke oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained.
English – 17 FUEL HANDLING • In temperatures below 32 ° F (0 ° C) some oils become too viscous. This can o verload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. Fueling Clean the area around the fuel cap .
18 – English ST AR TING AND ST OPPING Starting and stopping Cold engine Starting: The chain brake should be activ ated when star ting the chain saw . Activate the chain br ake by pushing the front hand guard f orwards. Ignition; choke: Slide the control to its rear position.
English – 19 ST AR TING AND ST OPPING • Ne ver star t a chain sa w unless the bar , chain and all cov ers are fitted correctly . See instructions under the heading Assembly . Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injur y .
20 – English W ORKING TECHNIQ UES Bef ore use: 1 Check that the chain br ake works correctly and is not damaged. 2 Check that the throttle loc kout works correctly and is not damaged. 3 Check that the stop s witch works correctly and is not damaged.
English – 21 W ORKING TECHNIQ UES incorrectly or make the cut in the wrong place the tree ma y hit you or the machine and cause y ou to lose control. Both situations can cause serious personal injur y . 8 Bef ore moving your chain sa w switch off the engine and lock the chain using the chain br ake.
22 – English W ORKING TECHNIQ UES Cutting with the bottom edge of the bar , i.e. from the top of the object downw ards, is known as cutting with a pulling chain. In this case the chain sa w pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting.
English – 23 W ORKING TECHNIQ UES The log is supported at one end. There is a high risk that it will split. Star t by cutting from belo w (about 1/3 of the wa y through). - Finish by cutting from abo ve so that the two cuts meet. The log is supported at both ends.
24 – English W ORKING TECHNIQ UES Felling F elling is done using three cuts. First y ou make the directional cuts, which consist of the top cut and the bottom cut, then y ou finish with the f elling cut. By placing these cuts correctly you can control the f elling direction very accurately .
English – 25 W ORKING TECHNIQ UES Limbing Mak e sure that y ou can stand and mov e about safely . Work on the left side of the trunk. Work as close as possib le to the chain saw f or maximum control. If possible, let the weight of the chain saw rest on the trunk.
26 – English MAINTENANCE General The user must only carry out the maintenance and ser vice work described in this manual. Carb uretor adjustment Due to e xisting environmental and emissions legislation your chain saw is equipped with mo vement limiters on the carburetor adjuster scre ws.
English – 27 MAINTENANCE Correctly adjusted carb uretor When the carburetor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max. speed. It is also impor tant that the chain does not rotate at idle.
28 – English MAINTENANCE Chain catcher Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw . Vibration damping system Regularly check the vibration damping units f or crac ks or def or mation. Make sure the vibr ation damping units are securely attached to the engine unit and handle unit.
English – 29 MAINTENANCE • Pull out the cord appro x. 30 cm (12 inches) and hook it into the notch in the rim of the pulley . Release the recoil spring by letting the pulley rotate slo wly backw ards. • Undo the screw in the centre of the pulle y and remov e the pulley .
30 – English MAINTENANCE An air filter that has been in use f or a long time cannot be cleaned completely . The filter m ust therefore be replaced with a new one at regular intervals .
English – 31 MAINTENANCE Maintenance sc hedule The f ollowing is a list of the maintenance that must be perf or med on the machine. Most of the items are descr ibed in the Maintenance section. Daily maintenance W eekly maintenance Monthly maintenance Clean the outside of the machine.
32 – English TECHNICAL D A T A T echnical data CS 2135T Engine Cylinder displacement, cu.in/cm 3 2,38/39 Cylinder bore, inch/mm 1,57/40 Stroke , inch/mm 1,22/31 Idle speed, r pm 2800 P ow er , kW/ r.
English – 33 TECHNICAL D A T A Recommended original and replacement bar and c hain combinations F ollowing is a list of recommended cutting equipment f or the Jonsered chain saw model CS 2135T .
34 – English FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT ´®z+R@Q¶5x¨ ´®z+R@Q¶5x¨ Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to e xplain the emissions control system warranty on y our 2001 and later small nonroad engine.
English – 35 AMERICAN ST AND ARD SAFETY PRECA UTIONS Safety precautions f or chain sa w users (ANSI B 175.1-2000 Anne x C) Kic kback safety precautions With a basic understanding of kickbac k, you can reduce or eliminate the element of sur prise. Sudden surprise contributes to accidents.
´®z+R@Q¶5x¨ 2006-11-19 ´®z+R@Q¶5x¨ 1150324-95.
Ein wichtiger Punkt beim Kauf des Geräts Jonsered CS 2135T (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Jonsered CS 2135T noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Jonsered CS 2135T - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Jonsered CS 2135T reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Jonsered CS 2135T erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Jonsered CS 2135T besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Jonsered CS 2135T verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Jonsered CS 2135T. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Jonsered CS 2135T gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
