Benutzeranleitung / Produktwartung ET-3410-J des Produzenten John Deere
Zur Seite of 24
Metal Cutting Saw Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE METAL SAW AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
2 Metal Cutting Saw Operator's Manual Congratulations on the purchase of your new John Deere 7-inch Metal Cutting Saw! You can be assured your metal cutting saw was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance.
Metal Cutting Saw Operator's Manual 3 T able of Content SAFETY ......................................................................................................................... .................. 4-13 GENERAL SAFETY RULES ................
4 Metal Cutting Saw Operator's Manual RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your tool or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices.
Metal Cutting Saw Operator's Manual 5 GENERAL SAFETY RULES: WORK AREA Keep work area clean and well lit. Cluttered areas and benches invite injuries. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
6 Metal Cutting Saw Operator's Manual MINIMUM GAUGE FOR EXTENSION CORDS VOLTS TOTAL LENGTH OF CORD IN FEET 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 AMPERAGE 0-6 18 16 16 14.
Metal Cutting Saw Operator's Manual 7 GENERAL SAFETY RULES: PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.
8 Metal Cutting Saw Operator's Manual CAUTION GENERAL SAFETY RULES: SERVICE Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts.
Metal Cutting Saw Operator's Manual 9 CAUTION SPECIFIC SAFETY RULES: DANGER: KEEP HANDS AND BODY AWAY FROM AND TO THE SIDE OF THE BLADE. CONTACT WITH BLADE WILL RESULT IN SERIOUS INJURY. DANGER: KEEP HANDS AWAY FROM CUTTING AREA AND BLADE. KEEP YOUR SECOND HAND ON AUXILIARY HANDLE, OR MOTOR HOUSING.
10 Metal Cutting Saw Operator's Manual CAUTION SPECIFIC SAFETY RULES: CAUSES AND OPERATOR PREVENTION OF KICKBACK: Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator.
Metal Cutting Saw Operator's Manual 11 CAUTION SPECIFIC SAFETY RULES: SUPPORT LARGE PANELS Large panels must be supported as shown in Fig. A to minimize the risk of blade pinching and kickback. When cutting operation requires the resting of saw on the work piece, the saw shall be rested on the larger portion and the smaller piece cut off.
12 Metal Cutting Saw Operator's Manual SPECIFIC SAFETY RULES: CONFIRM THAT NO ITEMS SUCH AS AN ELECTRIC CABLE OR CONDUIT ARE BURIED INSIDE Be sure the saw will not cut through wire, cable or conduit that are behind or under the area you are cutting.
Metal Cutting Saw Operator's Manual 13 SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS OF THIS TOOL! SPECIFIC SAFETY RULES: 1.
14 Metal Cutting Saw Operator's Manual Functional Description MODEL: ET-3410-J 7-INCH METAL CUTTING SAW NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.
Metal Cutting Saw Operator's Manual 15 Operation APPLICATIONS: Cutting various types of metals. ASSEMBLY: WARNING: ALWAYS DISCONNECT THE SAW FROM POWER SOURCE BEFORE MAKING ADJUSTMENTS. Install authorized saw blade as detailed in the "Change Saw Blade" on page 19.
16 Metal Cutting Saw Operator's Manual Operation PRE-OPERATION: SETTING BLADE DEPTH WARNING: DISCONNECT POWER CORD BEFORE ADJUSTING BLADE DEPTH. 1. Disconnect power cord. 2. Loosen T-knob (A). (Fig. 3) 3. Raise or lower the saw base to the desired position.
Metal Cutting Saw Operator's Manual 17 Operation OPERATION: CUTTING MATERIAL 1. The surface you are working on should be clean and level, free from rust, scale, dirt and chips. 2. Adjust the base plate to the desired bevel angle by loosening and then retightening the T-knob.
18 Metal Cutting Saw Operator's Manual Operation OPERATION (CONTINUED): EMPTY CHIP COLLECTOR WARNING: ALWAYS DISCONNECT THE SAW FROM THE POWER SOURCE BEFORE CHANGING BLADES, CLEARING CHIPS OR MAKING ADJUSTMENTS. CAUTION: ALLOW SAW TO COOL BEFORE EMPTYING CHIP COLLECTOR.
Metal Cutting Saw Operator's Manual 19 Maintenance and Inspection MAINTENANCE AND INSPECTION: CHANGING SAW BLADES WARNING: ALWAYS DISCONNECT THE SAW FROM THE POWER SOURCE BEFORE CHANGING BLADES, CLEARING CHIPS OR MAKING ADJUSTMENTS. 1. Disconnect power cord from receptacle.
20 Metal Cutting Saw Operator's Manual Maintenance and Inspection MAINTENANCE AND INSPECTION: WARNING: TO AVOID AN ACCIDENT OR PERSONAL INJURY, ALWAYS CONFIRM THAT THE TRIGGER SWITCH IS TURNED OFF AND THE POWER PLUG HAS BEEN DISCONNECTED FROM THE RECEPTACLE BEFORE PERFORMING ANY MAINTENANCE OR INSPECTION OF THIS TOOL.
Metal Cutting Saw Operator's Manual 21 Accessories ACCESSORIES: WARNING: ACCESSORIES FOR THIS POWER TOOL ARE MENTIONED IN THIS INSTRUCTION MANUAL. THE USE OF ANY OTHER ATTACHMENT OR ACCESSORY CAN BE DANGEROUS AND COULD CAUSE INJURY OR MECHANICAL DAMAGE.
22 Metal Cutting Saw Operator's Manual T roubleshooting TROUBLESHOOTING: Low Blade Life/Teeth Chipping: - Wrong blade for the type of material. a. AT-4423-J for mild steel up to 5/16" solid. b. AT-4424-J for aluminum up to 3/8" solid. c.
Metal Cutting Saw Operator's Manual 23 Notes.
24 Metal Cutting Saw Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 7-inch Metal Cutting Saw Operator's Manual #37-0746-021403 ©Copyright 2003, John Deere.
Ein wichtiger Punkt beim Kauf des Geräts John Deere ET-3410-J (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie John Deere ET-3410-J noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für John Deere ET-3410-J - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von John Deere ET-3410-J reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über John Deere ET-3410-J erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon John Deere ET-3410-J besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von John Deere ET-3410-J verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit John Deere ET-3410-J. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei John Deere ET-3410-J gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
