Benutzeranleitung / Produktwartung G6 des Produzenten JMR electronic
Zur Seite of 25
F F o o r r c c e e 4 4 G6 RAID System 6-bay Desktop Enclosur e Installation Guide May 29, 2002 • Revision B Patent Pending.
FORTRA Force 4 G6 Installation Guide Rev B ii Copyright Copyright 1998, 1999, 2001 by JMR Electronics, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, .
FORTRA Force 4 G6 Installation Guide Rev B iii T able of Contents 1. Intr oduction 2/4/6/8/10/12/15-bay Product Family Features . . . . . . . . . . . . . . . . . . . . .1-1 6-bay Desktop Specifications . . . . . . . . . . . . . . . . . . . . .
5. Blower Operation Blower Removal/Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1 Blower Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2 6. Power Supply Operation Power Supply Removal/Insertion .
FORTRA Force 4 G6 Installation Guide Rev B 1-1 The FOR TRA F F o o r r c c e e 4 4 G6 RAID System is designed for use with a host system to provide a high-end desktop RAID storage solution.
FORTRA Force 4 G6 Installation Guide Rev B 1-2 FOR TRA F F o o r r c c e e 4 4 products use advanced mid-plane technology developed by JMR, that allows power supplies, drives, and all other enclosure components to interface into a single board.
Dual Loops (A & B) A single loop is required for unit operation however both loops can be used to connect to different hosts, dual host adapters, and other devices, for flexible and even redundant configurations. For specific connection and installation information, refer to Chapter 4 .
FORTRA Force 4 G6 Installation Guide Rev B 2-1 This chapter covers specification information for the FOR TRA F F o o r r c c e e 4 4 G6 RAID System enclosure.
Disclaimer The original product packaging has been tested and is safe under normal shipping circumstances. Reshipping the product without using the original product packaging will void the warranty .
FORTRA Force 4 G6 Installation Guide Rev B 3-1 This chapter covers Fibre Channel device installation for FOR TRA F F o o r r c c e e 4 4 G6 desktop enclosure. SCA Connection and Hot-Swapping The unit uses SCA-2 type connectors which provide a safe means of connection/disconnection when hot-swapping devices.
Drive Installation Device mounting screws are included with the unit for device mounting. The JMR part number for the #6-32" mounting screws is HDS-01906. 1. After removing the canister , place it on a static free surface along with the device to be installed.
4. Repeat steps 1 through 3 until all devices are installed. 5. Configure ID, and other options as required (see Chapter 4 ). 6. Establish host connection (see Chapter 4 ).
This chapter covers the Fibre Channel setup for the FOR TRA F F o o r r c c e e 4 4 G6 system. This figure shows the slot numbering sequence used to refer to device canisters and also shows the default ID value for each slot.
Default Slot ID Drive Bay Default ID/Jumper Slot 0 (top) ID 0 / W1 Slot 1 ID 1 / W2 Slot 2 ID 2 / W3 Slot 3 ID 3 / W4 Slot 4 ID 4 / W6 Slot 5 ID 5 / W7 Setting Slot ID The ID for each slot can be set using jumpers located on the backplane of the unit.
FORTRA Force 4 G6 Installation Guide Rev B 4-3 Fibre ID Jmp 0 Jmp 1 Jmp 2 Jmp 3 Jmp 4 Jmp 5 Jmp 6 0 CCCCCCC 1 O CCCCCC 2 C O CCCCC 3 O OCCCCC 4 CC O CCCC 5 O C O C C C C 6 C O O C C C C 7 O O .
Legend: O = Open (no jumper) C = Closed (jumper on) Option Settings Additional drive option jumpers for remote and delayed start are located on the unit I/O board. They must be set at the factory . Remote Start This feature is disabled by default and can be enabled for OEM use.
CH-A 1 Loop A connection 1. This is a SFP fibre channel connector used to connect to a host system or to an expansion chassis for Loop A. CH-A 2 Loop A connection 2. This is a SFP fibre channel connector used to connect to a host system or to an expansion chassis for Loop A.
FORTRA Force 4 G6 Installation Guide Rev B 5-1 This chapter covers operations of the blower for the FOR TRA F F o o r r c c e e 4 4 G6 units.
3. Unplug the blower from the backplane. The connector is keyed so that it can be reinstalled correctly and has also been placed through a holder on the fan bracket to keep it out of the way during fan installation and removal. Reverse the steps to reinstall the blower .
This chapter covers the operations of the power supply for FOR TRA F F o o r r c c e e 4 4 G6 units. For operation, the AC cord (included) must be connected to the AC Inlet at the back of the unit, and the On/Off switch must be switched ON. The Status LED on the power supply will light to indicate the power supply is functioning properly .
Power Supply Replacement If the Power supply Status LED indicator is ‘ Red’ , the power supply may need to be replaced. The unit should be reset (turned on & off), and the power supply should be removed and then reinstalled.
This chapter covers the installation of the Intel PCI RAID Controller that is shipped with the FOR TRA Force 4 G6 RAID System. The model number of the PCI RAID Controller is ICP V ortex number.
FORTRA Force 4 G6 Installation Guide Rev B 8-1 For current information on this product, including updates to the manual and technical support related issues, please contact the sales support section of our web page at www .jmr .com, or you can contact our T echnical Support division directly at the address below .
FORTRA Force 4 G6 Installation Guide Rev B A-1 Drive Manufacturers Fujitsu Internet Address: www .fcpa.com Hitachi Internet Address: www .hitachi.com IBM (International Business Machines Corporation) Internet Address: www .ibm.com Maxtor Internet Address: www .
Host Bus Adapter Manufacturers Adaptec, Inc. Internet Address: www .adaptec.com Antares Microsystems Internet Address: www .antares.com Emulex Corporation Internet Address: www .emulex.com JNI Corporation Internet Address: www .jni.com QLogic Corp. Internet Address: www .
Ein wichtiger Punkt beim Kauf des Geräts JMR electronic G6 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JMR electronic G6 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JMR electronic G6 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JMR electronic G6 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JMR electronic G6 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JMR electronic G6 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JMR electronic G6 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JMR electronic G6. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JMR electronic G6 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
