Benutzeranleitung / Produktwartung Cherokee (2014) des Produzenten Jeep
Zur Seite of 683
Cherokee Chrysler Group LLC OWNER’S MANUAL 2014 Cherokee 14KL74-126-AA First Edition Printed in U.S.A. 2014.
VEHICLES SOLD IN CANAD A With respect to any V ehicles Sold in Canada, the name Chrysler Gr oup LL C shall be deemed to be deleted and the name Chrysler Canada Inc. used in subs titution theref ore. DRIVING AND AL COHOL Drunken driving is one of the most frequent causes of accidents.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............
.
INTRODUCTION CONTENTS 䡵 INTRODUCTION ........................ 4 䡵 ROLLOVER W ARNING ................... 4 䡵 HOW TO USE THIS MANUAL .............. 5 䡵 W ARNINGS AND CAUTIONS .............. 7 䡵 VEHICLE IDENTIFICA TION NUMBER ........ 7 䡵 VEHICLE MODIFICA TIONS/AL TERA TIONS .
INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it repr esents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
Failure to use the driver and passenger seat belts pro- vided is a major cause of sever e or fatal injury . In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually .
6 INTRODUCTION.
W ARNINGS AND CAUTIONS This Owners Manual contains W ARNINGS against oper- ating pr ocedures that could result in a collision or bodily injury . It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
NOTE: It is illegal to remove or alter the VIN. VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A WORD ABOUT YOUR KEYS ............. 1 2 ▫ Ignition Node Module (IGNM) — If Equipped . .12 ▫ Keyless Ignition Node (KIN) .............. 1 3 ▫ Key Fob — If Equipped .................. 1 4 ▫ Ignition Or Accessory On Message .
▫ T ransmitter Battery Replacement ........... 2 6 ▫ General Information .................... 2 9 䡵 REMOTE ST AR TING SYSTEM — IF EQUIPPED . .29 ▫ How T o Use Remote Start ................ 3 0 䡵 DOOR LOCKS ......................... 3 4 ▫ Manual Door Locks .
▫ Supplemental Restraint System (SRS) — Air Bags ............................ 6 7 ▫ Advanced Front Air Bag Features ........... 7 0 ▫ Air Bag Deployment Sensors And Controls .... 7 4 ▫ Event Data Recorder (EDR) ............... 9 1 ▫ Child Restraints .
A WORD ABOUT YOUR KEYS Y our vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a Key Fob with Remote Keyless Entry (RKE) transmitter and an Ignition Node Module (IGNM).
Keyless Ignition Node (KIN) This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate when in position.
Key Fob — If Equipped The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key , which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead.
NOTE: Y ou can insert the double-sided emergency key into the lock cylinders with either side up. Emergency Key Removal (IGNM) Emergency Key Removal (KIN) 2 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICL.
Ignition Or Accessory On Message Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to place the ignition in the OFF position. In addition to the chime, the ignition or accessory on message will display in the cluster .
W ARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather . Interior heat build-up may cause serious injury or death. CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended.
CAUTION! The Sentry Key® Immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the Key Fobs provided with your new vehicle have been programmed to the vehicle electronics.
NOTE: When having the Sentry Key® Immobilizer Sys- tem serviced, bring all vehicle keys with you to an authorized dealer . Customer Key Programming Programming Key Fobs or RKE transmitters may be performed at an authorized dealer . General Information The Sentry Key® system complies with FCC rules Part 15 and with RSS-210 of Industry Canada.
T o Arm The System Follow these steps to arm the V ehicle Security Alarm: 1. Remove the key from the ignition system (refer to ⬙ Starting Pr ocedures ⬙ in ⬙ Starting And Operating ⬙ for further information). • For vehicles equipped with Keyless Enter-N-Go™, make sure the vehicle ignition system is ⬙ OFF ⬙ .
• Cycle the vehicle ignition system out of the OFF position. • For vehicles equipped with Keyless Enter-N-Go™ , press the Keyless Enter -N-Go™ Start/Stop button (requir es at least one valid Key Fob in the vehicle).
Security System Manual Override The V ehicle Security Alarm will not arm if you lock the doors using the manual door lock plunger . ILLUMINA TED ENTR Y The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door .
NOTE: Driving at speeds 5 mph (8 km/h) and above disables the system from r esponding to all RKE transmit- ter buttons for all RKE transmitters. Emergency Key Removal (KIN) Emergency Key Removal (IGNM.
T o Unlock The Doors And Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal.
T o Lock The Doors And Liftgate Press and release the LOCK button on the RKE transmit- ter to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal.
Programming Additional T ransmitters Programming Key Fobs or RKE transmitters may be performed at an authorized dealer . T ransmitter Battery Replacement The recommended r eplacement battery is one CR2032 battery . NOTE: • Per chlorate Material — special handling may apply .
2. Separating RKE halves requir es scr ew removal and gently prying the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar , then r eplace the battery . When replacing the battery , match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover .
new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 4. T o assemble the RKE transmitter case, snap the two halves together . General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada.
NOTE: • The vehicle must be equipped with an automatic transmission to be equipped with Remote Start. • Obstructions between the vehicle and RKE transmitter may reduce this range.
W ARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Mon- oxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious in- jury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children.
T o Enter Remote Start Mode Press and release the REMOTE ST AR T button on the RKE transmitter twice within five seconds. The vehicle doors will lock, the parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will r emain in the Remote Start mode for a 15 minute cycle.
T o Exit Remote Start Mode And Drive The V ehicle Before the end of 15 minute cycle, pr ess and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the V ehicle Security Alarm (if equipped). Then, prior to the end of the 15 minute cycle, press and release the ST AR T/STOP button.
DOOR LOCKS Manual Door Locks T o lock each door , r otate the door lock knob on each door trim panel forward. T o unlock the front doors, pull the inside door handle to the first detent or rotate the door lock button until the red indicator is visible.
W ARNING! (Continued) • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
If you press the power door lock switch while the ignition is in the ACC or ON/RUN position, and any front door is open, the power locks will not operate. This prevents you from accidentally locking the Key Fob in the vehicle. Place the ignition to the OFF position or closing the door will allow the locks to operate.
Child-Protection Door Lock System — Rear Doors T o provide a safer environment for small children riding in the r ear seats, the rear doors are equipped with a Child-Protection Door Lock system. T o use the system, open each rear door , use a flat blade screwdriver (or ignition key) and rotate the dial to the LOCK or UNLOCK position.
NOTE: • When the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. • After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
NOTE: • Passive Entry may be programmed ON/OFF; refer to “Uconnect® Settings” in “Understanding Y our Instru- ment Panel” for further information. • If wearing gloves on your hands, or if it has been raining on the Passive Entry door handle, the unlock sensitivity can be af fected, r esulting in a slower re- sponse time.
T o Unlock From The Passenger Side W ith a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors and the liftgate automatically .
NOTE: The vehicle will only unlock the doors when a valid Passive Entry RKE transmitter is detected inside the vehicle, and no valid Passive Entry RKE transmitter is detected outside the vehicle.
NOTE: If “Unlock All Doors 1st Press” is pr ogrammed in EVIC, all doors will unlock when you push the electronic liftgate release. If ⬙ Unlock Driver Door 1st press ⬙ is programmed in Uconnect®, only the liftgate will unlock when you press the electronic liftgate release.
NOTE: • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle r eacting and unlocking.
WINDOWS Power Windows The window controls on the driver’s door control all the door windows. There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the ACC or ON/RUN position.
W ARNING! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode.
NOTE: • If the window runs into any obstacle during auto- closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window . • Any impact due to rough road conditions may trigger the auto-reverse function unexpectedly during auto- closure.
W indow Lockout Switch The window lockout switch on the driver’s door trim panel allows you to disable the window controls on the rear passenger doors. T o disable the window controls, press and r elease the window lockout button (setting it in the DOWN position).
Wind Buffeting W ind buf feting can be described as the perception of pressur e on the ears or a helicopter-type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof or Sky Slider™ (if equipped) in certain open or partially open positions.
NOTE: Use the power door LOCK switch on either front door trim panel or the Remote Keyless Entry (RKE) transmitter to lock and unlock the liftgate. The manual door locks on the doors and the driver’s door lock cylinder will not lock and unlock the liftgate.
The power liftgate may also be opened or closed by pressing the LIFTGA TE button located on the front overhead console, or closed by pressing the LIFTGA TE button located on left rear trim panel, near the liftgate opening.
NOTE: • The power liftgate buttons will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • The power liftgate will not operate in temperatures below −22°F (−30°C) or temperatures above 150°F (65°C).
• If your liftgate is power closing and you put the vehicle in gear , the liftgate will continue to power close. However , vehicle movement may result in a detection of an obstruction. W ARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle.
• Fr ont seat belts incorporate pretensioners that may enhance occupant protection by managing occupant energy during an impact event • All seat belt systems (except the driver’s) include Automa.
W ARNING! • Never place a rear facing infant seat in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger , including a child in a rearward facing infant seat. • Only use a rearward-facing child restraint in a vehicle with a rear seat.
5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center . Phone numbers are provided under ⴖ If Y ou Need Assistance ⴖ . W ARNING! • Relying on the air bags alone could lead to more severe injuries in a collision.
W ARNING! (Continued) • In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Pulling Out The Lap/Shoulder Belt Latch Plate Inserting Latch Plate Into Buckle 58 THINGS T.
W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you prop- erly .
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up a bit on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
6. T o release the belt, push the red button on the buckle. The belt will automatically retract to its stowed posi- tion. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position. Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ shoulder belt.
Seat Belts In Passenger Seating Positions The seat belts in the passenger seating positions are equipped with Automatic Locking Retractors (ALR) which are used to secure a child restraint system. For additional information, refer to “Installing Child Re- straints Using The V ehicle Seat Belt” under the “Child Restraints” section.
position that has a belt with this feature. Children 12 years old and under should always be properly r e- strained in a vehicle with a rear seat. How T o Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted.
Energy Management Feature This vehicle has a safety belt system with an Energy Management featur e in the fr ont seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to release webbing in a controlled manner .
passenger is unbelted, the Seat Belt Reminder Light will turn on and remain on until both fr ont seat belts ar e fastened. The BeltAlert® warning sequence begins after the vehicle speed is over 5 mph (8 km/h), by blinking the Seat Belt Reminder Light and sounding an intermittent chime.
Seat Belts And Pregnant Women W e r ecommend that pregnant women use the seat belts throughout their pregnancy . Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
panel below the steering column and a Supplemental Passenger Side Knee Air Bag mounted in the instrument panel below the glove compartment. NOTE: The Driver and Front Passenger Advanced Fr ont Air Bags are certified to the new Federal regulations for Advanced Air Bags.
and rear passengers sitting next to a window . The SABIC air bags, are located above the side windows and their covers are also labeled: SRS AIRBAG. This vehicle is equipped with Supplemental Seat- Mounted Side Air Bags (SAB) to provide enhanced protection for an occupant during a side impact.
• Supplemental Passenger Side Knee Air Bag • Fr ont and Side Impact Sensors • Fr ont Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat T rack Position Sensors • Occupant Classification System (OCS) Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage driver and front passenger air bags.
Supplemental Seat-Mounted Side Air Bags (SAB) Supplemental Seat-Mounted Side Air Bags (SAB) may provide enhanced protection to help protect an occupant during a side impact. The SAB is marked with an air bag label sewn into the outboard side of the seats.
NOTE: • Air Bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed.
W ARNING! • Y our vehicle is equipped with left and right SABIC, do not stack luggage or other cargo up high enough to block the location of the SABIC.
Along with seat belts and pretensioners, Advanced Front Air Bags work with the Supplemental Driver and Pas- senger Side Knee Air Bags and the knee bolsters to provide impr oved protection for the driver and front passenger . Side air bags also work with seat belts to improve occupant protection.
including the severity and type of collision. Advanced Front Air Bags and Supplemental Driver and Front Passenger Knee Air Bags are not expected to reduce the risk of injury in rear , side, or rollover collisions.
The ORC contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. Also, the ORC turns on the Air Bag W arning Light in the instrument panel for approxi- mately four to eight seconds for a self-check when the ignition is first turned on.
• Occupant Classification Module (OCM) located in the front passenger seat • OCS Sensor located in the front passenger seat • Air Bag W arning Light The OCS will NOT prevent deployment of the passenger Advanced Front Air Bag.
W ARNING! • Never place a rear facing infant seat in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger , including a child in a rearward facing infant seat.
W ARNING! Occupants in the front passenger seat sitting improp- erly may cause the OCS to not classify the passen- ger ’ s weight accurately . This may result in serious injury or death in a collision.
The OCS may not classify the front passenger pr operly if: • The front passenger ’s weight is transferred to another part of the vehicle (like the door , arm rest or instru- ment panel) • The fr.
Not Seated Properly Not Seated Properly 2 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE 81.
Not Seated Properly Not Seated Properly 82 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE.
S W ARNING! Placing an object on the floor under the front pas- senger seat may prevent the OCS from working properly , which may result in serious injury or death in a collision.
W ARNING! Make sure that objects inside the Flip ’n Stow™ Front Passenger Seat Storage bin do not interfere with the latch before closing the seat. In addition, after closing the Front Passenger Seat Storage bin, make sure the front passenger seat cushion is pushed downward and fully latched to the base.
W ARNING! (Continued) passenger if the vehicle is involved in a collision. A modified vehicle may not comply with required Federal Motor V ehicle Safety Standards (FMVSS) and/or Canadian Motor V ehicle Safety Standards (CMVSS).
Air Bag deploys down and around the knee blocker/ glove box surface allowing the air bags to inflate to the full size. The air bags fully inflate in about 15 to 20 milliseconds. Supplemental Seat-Mounted Side Air Bag (SAB) Inflator Units The Supplemental Seat-Mounted Side Air Bags are de- signed to activate only in certain side collisions.
where the SABIC inflates. This especially applies to children. The SABIC is only about 3-1/2 in (9 cm) thick when it is inflated. Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed.
If A Deployment Occurs The Advanced Fr ont Air Bags are designed to deflate immediately after deployment. NOTE: Fr ont and/or side air bags will not deploy in all collisions.
Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. W ARNING! Deployed air bags and seat belt pretensioners can not protect you in another collision.
W ARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. T ake your vehicle to an authorized dealer for any air bag system service.
• The Air Bag W arning Light r emains on after the four to eight-second interval. • The Air Bag W arning Light comes on intermittently or remains on while driving. NOTE: If the speedometer , tachometer , or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.
NOTE: EDR data are recor ded by your vehicle only if a non-trivial crash situation occurs; no data are recor ded by the EDR under normal driving conditions and no per- sonal data (e.
Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. Y ou should also make sure that you can install it in the vehicle where you will use it. NOTE: • For additional information, r efer to www .
Summary Of Recommendations For Restraining Children In V ehicles Child Size, Height, W eight or Age Recommended T ype of Child Restraint Infants and T oddlers Children who are two years old or younger.
Infants And Child Restraints Safety experts recommend that children ride rearwar d- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. T wo types of child restraints can be used rearward-facing: infant carriers and convertible child seats.
have outgrown the rear -facing weight or height limit of their rear -facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat.
Integrated Child Booster Seat — If Equipped The Integrated Child Booster Seat is located in each outboard second-row passenger seat. The Booster Seat is designed for children weighing between 48 and 85 lbs (22 and 39 kg) and between 47 in (1 19 cm) and 57 in (145 cm) tall.
W ARNING! Securely lock the seat cushion into position before using the seat. Otherwise, the seat will not provide the proper stability for child seats and/or passengers.
Recommendations For Attaching Child Restraints Restraint T ype Combined W eight of the Child + Child Restraint Use any attachment method shown with an “X” Below LA TCH – Lower Anchors Only Seat Belt Only LA TCH – Lower Anchors + T op T ether Anchor Seat Belt + T op T ether Anchor Rear-Facing Child Restraint Up to 65 lbs (29.
Lower Anchors and T ethers for Children (LA TCH) Restraint System Y our vehicle is equipped with the child restraint anchor- age system called LA TCH, which stands for Lower Anchors and T ethers for CHildren. The LA TCH system has three vehicle anchor points for installing LA TCH- equipped child seats.
LA TCH-equipped child seats without using the vehicle’s seat belts. Some seating positions may have a top tether anchorage but no lower anchorages. In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.
What is the weight limit (child’s weight + weight of the child restraint) for using the LA TCH anchorage system to attach the child restraint? 65 lbs (29.5 kg) Use the LA TCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.
Can the rear -facing child restraint touch the back of the front passenger seat? Y es The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner ’s manual for more information.
Locating The LA TCH Anchorages In addition, there are tether strap anchorages behind each r ear seating position located on the back of the seat. LA TCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
Center Seat LA TCH This vehicle has 5 lower LA TCH anchorages in the r ear seat. Anchorages A and B are used for the right outboard position behind the front passenger (1). Anchorages D and E are used for the left outboar d position behind the driver (3).
and buckle, the center seat belt can be used to restraint an occupant or child r estraint in the center seating position. 2. Right outboard and center seating positions (1 and 2): Install the first child seat in the right outboard seating position using lower anchorages A and B.
W ARNING! (Continued) • If you are installing three child restraints next to each other , you must use the seat belt and the center tether anchor for the center position. Y ou must use the LA TCH anchors to install the child seat in position (3), behind the driver .
4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “Installing Child Restraints Using the T op T ether Anchorage” for direc- tions to attach a tether anchor .
the child restraint installation, instead of buckling it behind the child restraint, route the seat belt through the child r estraint belt path and then buckle it. Do not lock the seatbelt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them.
into the retractor . For additional information on ALR, refer to the “Automatic Locking Mode” description un- der “Occupant Restraints.” The cinching latch plate is designed to hold the lap portion of the seatbelt tight when webbing is pulled tight and straight thr ough a child restraint’s belt path.
What is the weight limit (child’s weight + weight of the child re- straint) for using the T ether Anchor with the seat belt to attach a forward facing child restraint? W eight limit of the Child Res.
Installing A Child Restraint With A Switchable Automatic Locking Retractor (ALR) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit.
8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See the section “Installing Child Restraints Using the T op T ether Anchorage” for directions to attach a tether anchor .
4. Finally , pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearwar d and downward into the vehicle seat.
Installing Child Restraints Using The T op T ether Anchorage 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. Y ou may need to move the seat forward to provide better access to the tether anchorage.
W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly be- hind the child seat to secure a child restraint top tether strap.
CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty .
Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision.
W ARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury . • Always make sure that floor mats are properly attached to the floor mat fasteners.
Periodic Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks.
.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS ........................... .130 ▫ Inside Day/Night Mirror ............... .130 ▫ Automatic Dimming Mirror — If Equipped . . .130 ▫ Outside Mirrors ..................... .132 ▫ Power Mirrors .
▫ Head Restraints ..................... .154 ▫ 60/40 Split Folding Rear Seat W ith Fold-Flat Feature ........................... .156 䡵 DRIVER MEMORY SEA T — IF EQUIPPED . . . .159 ▫ Pr ogramming The Memory Feature ........ .159 ▫ Linking And Unlinking The Remote Keyless Entry T ransmitter T o Memory .
▫ Interior Lights ...................... .173 ▫ Battery Saver Feature ................. .175 䡵 WINDSHIELD WIPERS AND W ASHERS ..... .175 ▫ W indshield W iper Operation ............ .176 ▫ Intermittent W iper System .............. .177 ▫ W indshield W asher Operation .
▫ T o Resume ......................... .196 ▫ T o V ary The Speed Setting .............. .197 ▫ Setting The Following Distance In ACC ..... .198 ▫ Overtake Aid ....................... .202 ▫ ACC Operation at Stop ................ .202 ▫ Adaptive Cruise Control (ACC) Menu .
▫ ParkSense® System Usage Precautions ...... .239 䡵 P ARKSENSE® FRONT AND REAR P ARK ASSIST — IF EQUIPPED ........................ .241 ▫ ParkSense® Sensors ................... .243 ▫ ParkSense® W arning Display ............ .244 ▫ ParkSense® Display .
▫ Using HomeLink® .................... .282 ▫ Security ........................... .282 ▫ T roubleshooting T ips .................. .282 ▫ General Information ................... .283 䡵 POWER SUNROOF WITH POWER SHADE — IF EQUIPPED .......
▫ W ind Buffeting ...................... .293 ▫ Sky Slider™ Maintenance ............... .294 䡵 ELECTRICAL POWER OUTLETS .......... .294 䡵 POWER INVERTER — IF EQUIPPED ....... .297 䡵 WIRELESS CHARGING P AD — IF EQUIPPED . .298 ▫ W ir eless Charging Pad Operation .
MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirr or that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting.
left, and right for various drivers. The mirr or should be adjusted to center on the view through the rear window . This mirror automatically adjusts for headlight glare from vehicles behind you. NOTE: • The Automatic Dimming Mirr or feature is disabled when the vehicle is in reverse gear to improve rear view viewing.
Assist Call The rear view mirror contains an ASSIST push button which automatically connects the vehicle occupants to one of several predefined locations for immediate sup- port: • Roadside Assistance – If you get a flat tire, or need a tow , just press the Assist button and you’ll be con- nected to someone who can help.
NOTE: The passenger side convex outside mirror will give a much wider view to the rear , and especially of the lane next to your vehicle. W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
Models W ith Express Window Feature Press and release the mirror select button marked L (left) or R (right) and then press one of the four arrow buttons to move the mirror in the direction the arrow is pointing. The selection will time out after 30 seconds of inactivity to guard against accidentally moving a mirror position following an adjustment.
• The mirrors ar e accidentally manually folded/unfolded. • The mirrors come out of the unfolded position. • The mirrors shake and vibrate at normal driving speeds. T o r eset the power folding mirr ors : Fold and unfold them by pressing the button.
Sun Visor “Slide-On-Rod” Feature — If Equipped The sun visor “Slide-On-Rod” feature allows for addi- tional flexibility in positioning the sun visor to block out the sun. 1. Fold down the sun visor . 2. Unclip the visor from the center clip.
The BSM detection zone covers approximately one lane on both sides of the vehicle (12 ft or 3.8 m). The zone starts at the outside rear view mirror and extends ap- proximately 23 ft (7 m) to the rear of the vehicle.
The BSM system monitors the detection zone from three differ ent entry points (side, rear , fr ont) while driving to see if an alert is necessary . The BSM system will issue an alert during these types of zone entries. Entering From The Side V ehicles that move into your adjacent lanes from either side of the vehicle.
Entering From The Rear V ehicles that come up from behind your vehicle on either side and enter the r ear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking T raffic If you pass another vehicle slowly (with a relative speed less than 15 mph (24 km/h) and the vehicle r emains in the blind spot for approximately 1.
Overtaking/Approaching Overtaking/Passing 140 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However , occasionally the system may alert on such objects. This is normal operation and your vehicle does not requir e service.
W ARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals.
NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver .
Blind Spot Alert Lights/Chime When operating in Blind Spot Alert Lights/Chime mode, the BSM system will provide a visual alert in the appro- priate side view mirror based on a detected object. If the turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded.
SEA TS Seats are a part of the Occupant Restraint System of the vehicle. W ARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Reclining The Seatback Forward Or Rearward The seatback can be reclined both forward and rearward. Push the seat recliner switch forward or rearward, the seatback will move in the direction of the switch. Release the switch when the desired position has been reached.
Manual Seats — If Equipped Manual Front Seat Forward/Rearward Adjustment On models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor .
While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressur e, move forwar d and r earward on the seat to be sure that the seat adjusters have latched.
W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
Heated Seats — If Equipped On some models, the front and rear seats may be equipped with heaters located in the seat cushions. W ARNING! • Persons who are unable to feel pain to the skin because o.
NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. When the HI-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal HI-level.
NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. When the HI-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal HI-level.
Front V entilated Seats With Uconnect® 8.4A/8.4AN — If Equipped On some models, both the driver and passenger seats are ventilated. Located in the seat cushion and seatback ar e small fans that dra.
V ehicles Equipped With Remote Start On models that are equipped with remote start, the driver’s ventilated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things T o Know Before Starting Y our V ehicle” for further information.
The AHRs will automatically return to their normal position following a rear impact. If the AHRs do not return to their normal position see your authorized dealer immediately .
W ARNING! Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players. These items may interfere with the operation of the Active Head Restraint in the event of a collision and could result in serious injury or death.
NOTE: Prior to folding the rear seat, it may be necessary to position the front seat to its mid-track position. Also, be sure that the front seats are fully upright and posi- tioned forwar d. This will allow the r ear seat to fold down easily . W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
T o Raise The Rear Seat NOTE: If interfer ence from the car go area pr events the seatback from fully locking, you will have difficulty returning the seat to its proper position. Raise the seatback and lock it into place. W ARNING! Be certain that the seatback is securely locked into position.
DRIVER MEMOR Y SEA T — IF EQUIPPED This feature allows the driver to store up to two different memory pr ofiles, for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat and side mirrors and a set of desired radio station presets.
2. Adjust all memory profile settings to desired prefer - ences (i.e., seat, side mirror and radio station presets). 3. Pr ess and release the SET button on the memory switch, then press the side of the number (1) button within five seconds.
Linking And Unlinking The Remote Keyless Entry T ransmitter T o Memory Y our Remote Keyless Entry (RKE) transmitters can be programmed to recall one of two pre-pr ogrammed memory profiles with a press of the UNLOCK button on the RKE transmitter .
Memory Position Recall NOTE: • For vehicles equipped with an automatic transmission, the vehicle must be in P ARK to recall memory posi- tions. If a recall is attempted when the vehicle is not in P ARK, a message will display in the EVIC, if equipped.
The distance the driver seat moves depends on where you have the driver seat positioned when you remove the key from the ignition switch. • When you remove the key from the ignition switch, the driver seat will move about 2.4 in (60 mm) rear- ward if the driver’s seat position is greater than or equal to 2.
TO OPEN AND CLOSE THE HOOD T wo latches must be released to open the hood. 1. Pull the hood r elease lever located under the drivers side of the instrument panel. 2. Move to the outside of the vehicle and pull the safety latch release lever forward (toward you).
CAUTION! T o prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, parking light and instrument panel light op- eration.
Headlights On With Wipers (Available with Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUT O position.
If you turn the headlights of f befor e the ignition, they will turn off in the normal manner . NOTE: • The lights must be turned off within 45 seconds of placing the ignition in the OFF position to activate this feature.
NOTE: • Automatic High Beam Headlamp Control can be turned on or off using the Uconnect® System, refer to “Uconnect® Settings” in “Understanding Y our Instru- ment Panel” for further information.
Fog Lights — If Equipped The front fog light switch is built into the headlight switch. T o activate the fr ont fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. T o turn off the fr ont fog lights, either press the headlight switch a second time or turn off the headlight switch.
T urn Signals Move the multifunction lever up or down and the arr ows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. NOTE: • If either light r emains on and does not flash, or ther e is a very fast flash rate, check for a defective outside light bulb.
Lane Change Assist T ap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam.
There are courtesy lights located above the front seats. If your vehicle is equipped with a power sunroof the courtesy lights ar e located above the rear seats. The courtesy lights can be turned on by pressing the lens. T o turn the lights off, press the lens a second time.
W ith the parking lights or headlights on, r otating the right dimmer control upwar d will incr ease the brightness of the instrument panel lights and lighted cupholders — if equipped.
Dome Light Position Rotate the instrument panel dimmer contr ol completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the instrument panel dimmer control is in this position. Interior Light Defeat (OFF) Rotate the instrument panel dimmer control to the ex- treme bottom OFF position.
Windshield Wiper Operation Rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation.
CAUTION! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur .
Windshield Washer Operation T o use the washer , pull the lever rearwar d toward you and hold while spray is desired. If the lever is pulled while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent interval pre- viously selected.
W ARNING! Sudden loss of visibility through the windshield could lead to a collision. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshield with the defroster before and during windshield washer use.
Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver . The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of five settings to activate this feature.
The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions: • Low Ambient T emperature — When the ignition is first turned O.
T o unlock the steering column, push the contr ol handle downward (towar d the floor). T o tilt the steering column, move the steering wheel upward or downward as de- sired. T o lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.
HEA TED STEERING WHEEL — IF EQUIPPED The steering wheel contains a heating element that helps warm your hands in cold weather . The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate up to 80 minutes before automatically shutting off.
Uconnect® 8.4 System — If Equipped T ouch the “Controls” soft-key then touch the “Heated Steering Wheel” soft-key to turn on the heated steering wheel. Press the “Heated Steering Wheel” soft-key a second time to turn the heated steering wheel off.
V ehicles Equipped With Remote Start On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things T o Know Before Starting Y our V ehicle” for further information.
NOTE: In order to ensur e pr oper operation, the Elec- tronic Speed Control System has been designed to shut down if multiple Speed Contr ol functions are operated at the same time.
W ARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. Y ou could accidentally set the system or cause it to go faster than you want. Y ou could lose control and have an accident. Always leave the system OFF when you are not using it.
Pressing the SET (+) button once will result i na1m p h (1 km/h) increase in set speed. Each subsequent tap of the button results in an increase of 1 mph (1 km/h).
W ARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Y our ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy , snow-covered or slippery .
W ARNING! • Adaptive Cruise Control (ACC) is a convenience system. It is not a substitute for active driving involvement. It is always the driver ’ s responsibil- ity to be attentive of road, traf.
W ARNING! (Continued) • When entering a turn lane or highway off ramp; when driving on roads that are winding, icy , snow- covered, slippery , or have steep uphill or downhill slopes. • When towing a trailer up or down steep slopes. • When circumstances do not allow safe driving at a constant speed.
NOTE: Any chassis/suspension or tire size modifica- tions to the vehicle will effect the performance of the Adaptive Cruise Contr ol. Activating Adaptive Cruise Control (ACC) Y ou can only engage ACC if the vehicle speed is above 0 mph (0 km/h). The minimum Set Speed for the ACC system is 20 mph (32 km/h).
NOTE: Y ou cannot enable ACC under the following conditions: • When in Four-Wheel Drive Low . • When you apply the brakes. • When the parking brake is set. • When the automatic transmission is in P ARK, RE- VERSE or NEUTRAL. • When the V ehicle speed is outside of the speed range.
T o turn the system OFF , push and r elease the Adaptive Cruise Control (ACC) ON/OFF button again. At this time, the system will turn off and the EVIC will display “Adaptive Cruise Contr ol (ACC) Of f.” W ARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous.
If the system is Set when the vehicle speed is below 20 mph (32 km/h), the Set Speed shall be defaulted to 20 mph (32 km/h). If the system is Set when the vehicle speed is above 20 mph (32 km/h), the Set Speed shall be the current speed of the vehicle.
T o T urn Off The system will turn off and clear the set speed in memory if: • Y ou push the Adaptive Cr uise Contr ol (ACC) ON/ OFF button. • Y ou push the Normal (Fixed Speed) Cruise Control ON/OFF button. • Y ou turn OFF the ignition. • Y ou switch to Four-Wheel Drive Low .
T o V ary The Speed Setting While ACC is set, you can increase the set speed by pressing the SET + button. Pressing the SET + button once will result i na1m p h (1 km/h) increase in set speed. Each subsequent tap of the button results in an increase of 1 mph (1 km/h).
• The ACC system maintains set speed when driving up hill and down hill. However , a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending down- hill. This is normal operation and necessary to main- tain set speed.
Distance Setting 3 Bars (Long) Distance Setting 2 Bars (Medium) 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 199.
T o increase the distance setting, press the Distance Set- ting — Increase button and release. Each time the button is pressed, the distance setting increases by one bar (longer). T o decrease the distance setting, pr ess the Distance Setting — Decrease button and release.
• The distance setting is changed. • The system disengages. (Refer to the information on ACC Activation). The maximum braking applied by ACC is limited; how- ever , the driver can always apply the brakes manually , if necessary . NOTE: The brake lights will illuminate whenever the ACC system applies the brakes.
Overtake Aid When driving with ACC engaged and following a target vehicle, the system will provide an additional accelera- tion to assist in passing vehicles in front. This additional acceleration is triggered when the driver utilizes the left turn signal.
W ARNING! When the ACC system is resuming speed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle. Failure to follow these warnings can result in a collision and death or serious personal injury . Adaptive Cruise Control (ACC) Menu The EVIC displays the current ACC system settings.
• System Off • ACC Proximity W arning • ACC Unavailable W arning • The EVIC will return to the last display selected after five seconds of no ACC display activity .
If weather conditions are not a factor , the driver should examine the sensor . It may r equire cleaning or removal of an obstruction. The sensor is located in the center of the vehicle behind the lower grille. T o keep the ACC System operating properly , it is impor- tant to note the following maintenance items: • Always keep the sensor clean.
“Clean Front W indshield” W arning The “ACC / FCW Limited Functionality Clean Front W indshield” warning will display and also a chime will indicate when conditions temporarily limit system per- formance. This most often occurs at times of poor visibil- ity , such as in snow or heavy rain and fog.
Service ACC/FCW W arning If the system turns off, and the EVIC displays “ACC/ FCW Unavailable Service Required”or “Cruise/FCW Unavailable Service Required”, there may be an internal system fault or a temporary malfunction that limits ACC functionality .
T urns And Bends When driving on a curve with ACC engaged, the system may decrease the vehicle speed and acceleration for stability reasons, with no target vehicle detected. Once the vehicle is out of the curve the system will resume your original Set Speed.
Using ACC On Hills When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC perfor- mance may be limited. Lane Changing ACC may not detect a vehicle until it is completely in the lane in which you ar e traveling.
Narrow V ehicles Some narr ow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane.
Stationary Objects And V ehicles ACC does not react to stationary objects and stationary vehicles. For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if necessary .
(Fixed Speed) CONTROL OFF . Pressing of the NORMAL (Fixed Speed) CRUISE CONTROL ON/OFF button will result in turning ON (changing to) the Normal (Fixed Speed) Cruise Contr ol mode. W ARNING! In the Normal (Fixed Speed) Cruise Control mode, the system will not react to vehicles ahead.
set speed will continue to increase in 5 mph (10 km/h) increments until the button is r eleased. The incr ease in set speed is reflected in the EVIC display . T o decr ease speed while the Normal (Fixed Speed) Cruise Control is set, push the SET (-) button.
T o T urn Of f The system will turn off and erase the set speed in memory if: • Y ou push the Normal (Fixed Speed) Cruise Control ON/OFF button. • Y ou turn off the ignition. • Y ou engage Four-Wheel Drive Low . • Y ou push the Adaptive Cruise Control (ACC) On/Off button.
NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller (EBC), to calculate the probability of a forward collision. When the system determines that a forward collision is probable, the driver will be provided with audible and visual warnings and may provide a brake jerk warning.
NOTE: • The minimum speed for FCW activation is 5 mph (10 km/h). • The FCW alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal FCW activation and functionality .
T o turn the FCW system OFF , press the forward collision button once to turn the system OFF (led turns on). T o turn the FCW system back ON, press the forwar d collision button again to turn the system ON (led turns off).
Changing FCW And Active Braking Status T o Change The FCW Sensitivity And Active Braking Settings W ith Uconnect® 8.4/8.4A System Screen — If Equipped. Follow these steps to set the FCW Sensitivity and Active Braking: NOTE: The settings can only be changed when the vehicle is in P ARK.
5. Pr ess the “FWD Collision W arning” Far or Near soft-key for your desired preference. Then press the back arrow . 6. Pr ess the second “FWD Collision W .
Once the condition that limited the system performance is no longer present, the system will return to its full performance state. If the problem persists, see your authorized dealer .
The driver may manually override the haptic warning by applying torque into the steering wheel at any time. When only a single lane marking is detected and the driver unintentionally drifts across the.
T o turn the LaneSense system ON, press the LaneSense button to turn the system ON (LED turns of f). A “Lane Sense On” message is shown in the EVIC. T o turn the LaneSense system OFF , press the LaneSense button once to turn the system OFF (LED turns on).
Left Lane Departure — Only Left Lane Detected • When the LaneSense system is ON, the LaneSense indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the EVIC if an uninten- tional lane departure occurs.
NOTE: The LaneSense system operates with the similar behavior for a right lane departur e when only the right lane marking has been detected. Left Lane Departure — Both Lanes Detected • When the LaneSense system is ON, the lane lines turn from gray to white to indicate that the lane markings have been detected.
• For example: If approaching the left side of the lane the steering wheel will turn to the right. • When the LaneSense system senses the lane has been approached and is in a lane departure situat.
NOTE: The LaneSense system operates with the similar behavior for a right lane departure. 7.0 EVIC Screen — If Equipped When the LaneSense system is ON; the lane lines are gray when the lane boundaries have not been detected and the LaneSense indicator is solid white.
Left Lane Departure — Only Left Lane Detected • When the LaneSense system is ON, the LaneSense indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the EVIC if an uninten- tional lane departure occurs.
Left Lane Departure — Both Lanes Detected • When the LaneSense system is ON, the lane lines turn from gray to white to indicate that the lane markings have been detected.
• For example: If approaching the left side of the lane the steering wheel will turn to the right. • When the LaneSense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes thick yellow to thin yellow .
NOTE: The LaneSense system operates with the similar behavior for a right lane departure. Changing LaneSense Status The LaneSense system settings can be configured through the Uconnect® system screen. Follow these steps to change the LaneSense settings: 1.
NOTE: • When enabled the system operates above 37 mph (60 km/h) and below 1 12 mph (180 km/h). • Use of the turn signal suppresses the warnings. • The system will not apply torque to the steering wheel whenever a safety system engages. (anti-lock brakes, traction control system, electronic stability control, forward collision warning, etc.
(200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orienta- tion of the obstacle. ParkSense® W arning Display The ParkSense® W arning screen will only be displayed if Sound and Display is selected from the Customer - Programmable Features section of the Uconnect® Sys- tem.
Single 1/2 Second T one/Solid Arc Slow T one/Solid Arc 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 233.
Slow T one/Solid Arc Fast T one/Flashing Arc 234 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting .
W ARNING ALER TS Rear Dis- tance (in/cm) Greater than 79 in (200 cm) 79-59 in (200-150 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) Less than 12 in (30 cm) .
NOTE: ParkSense® will reduce the volume of the radio, if on, when the system is sounding an audio tone. Enabling And Disabling ParkSense® ParkSense® can be enabled and disabled with the ParkSense® switch, located on the switch panel below the Uconnect® display .
REVERSE and the system is disabled, the EVIC will display the “P ARKSENSE OFF” message for as long as the vehicle is in REVERSE. The ParkSense® switch LED will be ON when ParkSense® is disabled or r equires service. The ParkSense® switch LED will be OFF when the system is enabled.
Cleaning The ParkSense® System Clean the ParkSense® sensors with water , car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors.
system misinterpreting a close object as a sensor problem, causing the “P ARKSENSE UNA V AILABLE SER VICE REQUIRED” message to be displayed in the EVIC. • On vehicles equipped with a tailgate, ParkSense® should be disabled when the tailgate is in the lowered or open position and the vehicle is in REVERSE.
W ARNING! (Continued) • Before using ParkSense®, it is strongly recom- mended that the ball mount and hitch ball assem- bly is disconnected from the vehicle when the vehicle is not used for towing.
• Automatic brakes will not be available if ESC is not available. • Automatic brakes will not be available if ther e is a faulted condition detected with the ParkSense® Park Assist system or the Braking System Module.
ParkSense® will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the ON/RUN position. ParkSense® can be active only when the shift lever is in REVERSE or DRIVE (NON-REVERSE for manual trans- mission).
ParkSense® W arning Display The ParkSense® W arning screen will only be displayed if Sound and Display is selected from the Customer - Programmable Features section of the Uconnect® Sys- tem. Refer to ⬙ Uconnect® Settings” in “Understanding Y our Instrument Panel” for further information.
If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear r egion and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from fast to continuous.
Slow T one/Solid Arc Fast T one/Flashing Arc 246 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting .
W ARNING ALER TS Rear Dis- tance (in/cm) Greater than 79 in (200 cm) 79-59 in (200-150 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) Less than 12 in (30 cm) .
Radio V ol- ume Re- duced No Y es Y es Y es Y es Y es Y es NOTE: ParkSense® will reduce the volume of the radio, if on, when the system is sounding an audio tone. Front Park Assist When the vehicle is in DRIVE or NON-REVERSE for manual transmission, the ParkSense W arning screen will be displayed when an obstacle is detected.
No T one/Solid Arc No T one/Flashing Arc 250 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting .
W ARNING ALER TS Front Distance (in/cm) Greater than 47 in (120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) Less than 12 in (30 cm) Arcs — Left None None None 2nd Flashing 1st.
If the Uconnect® System is equipped, chime volume settings will not be accessible from the EVIC. The chime volume settings include LOW , MEDIUM, and HIGH. The factory default volume setting is MEDIUM. ParkSense will retain its last known configuration state through ignition cycles.
REVERSE and the system is disabled, the EVIC will display the “P ARKSENSE OFF” message for as long as the vehicle is in REVERSE. The ParkSense® switch LED will be ON when ParkSense® is disabled or requires service. The ParkSense® switch LED will be OFF when the system is enabled.
If ⬙ P ARKSENSE UNA V AILABLE WIPE REAR SENSORS ⬙ or ⬙ P ARKSENSE UNA V AILABLE WIPE FRONT SEN- SORS ⬙ appears in the Electronic V ehicle Information Center (EVIC) make sure the outer surface .
• ParkSense®, when on, will reduce the volume of the radio when it is sounding a tone. • Clean the ParkSense® sensors r egularly , taking care not to scratch or damage them. The sensors must not be covered with ice, snow , slush, mud, dirt or debris.
CAUTION! (Continued) • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense®. W ARNING! • Drivers must be careful when backing up even when using ParkSense®.
providing audible/visual instructions, and controlling the steering wheel. The ParkSense® Active Park Assist system is defined as “semi-automatic” since the driver maintains control of the accelerator , shift lever and brakes.
T o enable the ParkSense® Active Park Assist system, press the ParkSense® Active Park Assist switch once (LED turns on). T o disable the ParkSense® Active Park Assist system, press the ParkSense® Active Park Assist switch again (LED turns off).
• Performing 6 parking attempts to position the vehicle into the parking space. The ParkSense® Active Park Assist system will only operate and search for a parking space when the follow- ing condit.
display . Y ou may switch to perpendicular parking if you desire. Push the OK button on the left side steering wheel switch to change your parking space setting. NOTE: • When searching for a parking space, use the turn signal indicator to select which side of the vehicle you want to perform the parking maneuver .
When an available parking space has been found, and the vehicle is not in position, you will be instructed to move forward to position the vehicle for a parallel parking sequence. Once the vehicle is in position, you will be instructed to place the shift lever into the REVERSE position.
NOTE: • It is the driver ’s responsibility to use the brake and accelerator during the semi-automatic parking maneu- ver . • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly .
When the vehicle has been moved into the parallel park position you will be instructed to place the shift lever into the DRIVE position, move forward slowly and check your surroundings.
Y our vehicle is now in the parallel park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to P ARK. The ⬙ Active ParkSense Complete - Check Parking Position ⬙ message will be momentarily displayed.
wheel switch to change your parking space setting to a perpendicular maneuver . Y ou may switch back to paral- lel parking if you desire. NOTE: • When searching for a parking space, use the turn signal indicator to select which side of the vehicle you want to perform the parking maneuver .
When an available parking space has been found, and the vehicle is not in position, you will be instructed to move forward to position the vehicle for a perpendicular parking sequence. Once the vehicle is in position you will be instructed to place the shift lever into the REVERSE position.
NOTE: • It is the driver ’s responsibility to use the brake and accelerator during the semi-automatic parking maneu- ver . • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly .
When the vehicle has been moved into the perpendicular park position you will be instructed to place the shift lever into the DRIVE position, move forward slowly , and check your surroundings.
Y our vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to P ARK. The ⬙ Active ParkSense Complete - Check Parking Position ⬙ message will be momentarily dis- played.
CAUTION! • The ParkSense® Active Park Assist system is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close prox- imity .
W ARNING! (Continued) • Before using the ParkSense® Active Park Assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing.
vehicle is shifted into P ARK or the ignition is switched to the OFF position. A touch screen control (soft button) to disable display of the camera image is made available when the vehicle is not in REVERSE gear .
W ARNING! Drivers must be careful when backing up even when using the ParkV iew® Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up.
4. Pr ess the check box soft key next to “Parkview® Backup Camera” to enable/disable. NOTE: A check mark will appear in the selection box to indicate the system is turned ON. T urning ParkView® On Or Off — W ith Uconnect® 8.4A/8.4AN 1. Pr ess the “Controls” soft-key located on the bottom of the Uconnect® display .
NOTE: HomeLink® is disabled when the V ehicle Secu- rity Alarm is active. Before Y ou Begin Programming HomeLink® Be sure that your vehicle is parked outside of the garage before you begin programming.
NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when pr ogramming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or , on the Internet at www .
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to pro- gram while keeping the HomeLink® indicator light in view . 3. Simultaneously press and hold both the HomeLink® button you want to program and the hand-held trans- mitter button.
Reprogramming A Single HomeLink® Button T o reprogram a channel that has been previously trained, follow these steps: 1. T urn the ignition switch to the ON/RUN position. 2. Pr ess and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds.
• T o program the remaining two HomeLink® buttons, repeat each step for each r emaining button. DO NOT erase the channels. Reprogramming A Single HomeLink® Button T o reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to pro- gram while keeping the HomeLink® indicator light in view .
3. W ithout releasing the button proceed with “Canadian/Gate Operator Pr ogramming” Step 2 and follow all remaining steps. Using HomeLink® T o operate, press and release the programmed HomeLink® button. Activation will now occur for the programmed device (i.
W ARNING! • Y our motorized door or gate will open and close while you are programming the universal trans- ceiver . Do not program the transceiver if people, pets or other objects are in the path of the door or gate.
POWER SUNROOF WITH POWER SHADE — IF EQUIPPED The power sunroof switch is located to the left between the sun visors on the overhead console. The power shade switch is located to the right between the sun visors on the overhead console.
W ARNING! • Never leave children unattended in a vehicle, and do not leave the key fob in or near the vehicle. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/Run mode. Occupants, particularly unattended chil- dren, can become entrapped by the power sunroof while operating the power sunroof switch.
Opening Sunroof — Manual Mode A comfort stop position is a programmed automatic stop for the sunroof open position. The comfort stop position has been optimized to minimize wind buffeting.
NOTE: If the sunshade is in the closed position when the vent switch is pressed, the sunshade will automatically cycle to the halfway open position prior to the sunroof opening to the V ent position.
Closing Power Shade — Manual Mode T o close the shade, press and hold the switch in the forward position. Any release of the switch will stop the movement and the shade will remain in a partially closed condition until the switch is pushed and held forward again.
Ignition Off Operation For V ehicles Not Equipped W ith The Electronic V ehicle Information Center (EVIC) The power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
CAUTION! (Continued) • Never attempt to open or close the Sky Slider™ when it is frozen. W ait until the Sky Slider™ is thawed before operating. • Opening the Sky Slider™ when damp, wet, or dirty can cause stains, mildew , and damage to the soft- top material and the inside of your vehicle.
W ARNING! (Continued) • If potential danger exists while opening or closing the Sky Slider™ in Automatic Mode, press and release the switch immediately to interrupt the operation. • If potential danger exists while opening or closing the Sky Slider™ in Operator Mode, release the switch immediately to interrupt the operation.
• T o resume the operation from a partially open posi- tion, press and release the switch a second time. • The Sky Slider™ will not open from the front and the rear at the same time. The Sky Slider™ must close fully before opening it from the opposite end.
Manual Override The Sky Slider™ drive motors are mounted to the roof above the car go lamp. In the event that your vehicle losses battery power , you can close the Sky Slider™ by turning the drive gears in the appropriate motor with a 6 mm Allen wr ench.
Sky Slider™ Maintenance Refer to “Sky Slider™ T op Care” in “Maintaining Y our V ehicle” for further information. ELECTRICAL POWER OUTLETS Y our vehicle is equipped with 12 V olt (13 Amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories.
In addition to the fr ont power outlet, ther e is also a power outlet located in the storage area of the center console. The rear power outlet is located in the right rear car go area. W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet.
W ARNING! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.
POWER INVERTER — IF EQUIPPED There is a 1 15 V olt, 150 W att inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 W atts.
W ARNING! T o avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use.
your Qi enabled mobile phone. Qi is a standard that uses magnetic induction to transfer power to your mobile device. Y our mobile phone must be designed for Qi wireless charging, be equipped with an aftermarket sleeve or equipped with a back plate from your mobile phone provider .
NOTE: The initial adjustment will only need to be done once as long as only one mobile phone is used. If a differ ent mobile phone is used, the cradle will need to be readjusted. The LED indicator will flash green while the mobile phone is char ging. The Qi enabled phone is able to function normally as it is charging.
CUPHOLDERS There ar e two cupholders for the front seat passengers, located in the center console. There are two cupholders for the rear seat passengers, located in the center armrest.
STORAGE Glove Box Storage Compartment The glove box storage compartment is located on the passengers side of the instrument panel. Pull outward on the latch to open the storage compartment. There is also an additional storage bin located above the instrument panel in the center of the dash.
Console Storage Compartment Some vehicles may be equipped with a wireless charging pad located in the upper portion of the center console. Refer to W ireless Charging Pad-If Equipped in this section for more information. T o open, pull up on the latch and lift the cover .
The center console has a storage area which can hold cell phones, PDAs, and other small items. W ARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving.
Rear Storage Bin The rear storage bins are located in the rear of the vehicle on the sides of the load floor . Cargo T ie-Down Hooks And Loops The tie-downs located on the cargo area floor should be used to secure loads safely when the vehicle is moving.
W ARNING! The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. T o avoid loss of control resulting in per- sonal injury , follow these guideli.
The r emovable retractable car go area cover mounts in the cargo area behind the top of the rear seats. The cover , when extended, covers the cargo area to keep items out of sight. Notches in the trim panels near the liftgate opening secure the extended cover in place.
W ARNING! In a collision, a cargo cover loose in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting.
and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent inter- val previously selected. If the lever is pushed while the wiper is in the off position, the wiper will operate for several wipe cycles, then turn off.
CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window . Do not use abrasive window cleaners on the interior surface of the window . Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
CAUTION! • T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity . Always distribute heavy loads as evenly as pos- sible and secure the load appropriately . • Long loads, which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle.
.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 INSTRUMENT P ANEL FEA TURES ......... .315 䡵 INSTRUMENT CLUSTER — BASE ......... .316 䡵 INSTRUMENT CLUSTER — PREMIUM ..... .317 䡵 INSTRUMENT CLUSTER DESCRIPTIONS .... .318 䡵 ELECTRONIC VEHICLE INFORMA TION CENTER (EVIC) .
䡵 Uconnect® RADIOS — IF EQUIPPED ....... .382 䡵 iPod®/USB/MP3 CONTROL — IF EQUIPPED . .382 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED .......................... .383 ▫ Radio Operation ..................... .384 ▫ CD Player .......
INSTRUMENT P ANEL FEA TURES 1 — Air Demister Outlet 5 — Instrument Cluster 9 — Passenger Air Bag 13 — Stop/Start Ignition Button 2 — Air Outlet 6 — Electronic Speed Controls 10 — Glove C.
INSTRUMENT CLUSTER — BASE 316 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER — PREMIUM 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 317.
INSTRUMENT CLUSTER DESCRIPTIONS 1. T achometer Indicates the engine speed in revolutions per minute (RPM x 1000). 2. High Beam Indicator Indicates that headlights are on high beam. 3. Fr ont Fog Light Indicator — If Equipped This indicator will illuminate when the front fog lights are on.
When the appropriate conditions exist, this display shows the Electronic V ehicle Information Center (EVIC) messages. Refer to “Electronic V ehicle Information Center”. 6. Brake W arning Light This light monitors various brake functions, including brake fluid level and parking brake application.
W ARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. Y ou could have a collision. Have the vehicle checked immediately . V ehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD).
brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer .
10. Speedometer Indicates vehicle speed. 1 1. Seat Belt Reminder Light When the ignition switch is first turned to the ON/RUN position, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
possible, and inflate them to the pr oper pressur e. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability .
CAUTION! (Continued) equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Y our V ehicle”.
CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur .
This system allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: • Speedometer • V ehicle Info .
The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: • UP Arrow Button Press and release the UP arrow button to scroll upward through t.
• BACK/LEFT Arrow Button Press and release the LEFT arr ow button to access the information screens or sub-menu screens of a main menu item. • OK Button Press the OK button to access/select the information screens or sub-menu screens of a main menu item.
If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir , it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electr onic Stability Control (ESC) system.
Operation of the Brake W arning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected.
messages that consist of appr oximately 60 possible warn- ing or information messages. These pop up messages fall into several categories: • Five Second Stored Messages When the appr opriate conditions occur , this type of message takes control of the main display area for five seconds and then returns to the previous screen.
5. Lane Departure W arning (LDW) — If Equipped The Lane Departure W arning (LDW) system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. • When the LDW system is ON and ready the lane lines and LDW indicator are the color gray .
The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake W arning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.
The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN posi- tion. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 7. Fuel Gauge Fuel Gauge displays the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.
W ARNING! If you continue operating the vehicle when the T ransmission T emperature W arning Light is illumi- nated you could cause the fluid to boil over , come in contact with hot engine or exhaust components and cause a fire. • Low Coolant Level Indicator This telltale will turn on to indicate the vehicle coolant level is low .
1 1. Dedicated Speed W arning T elltale — If Equipped This area displays the dedicated speed warn- ing telltale. 12. Speed For Electronic Cruise Control Setting This displays the set speed of the Electronic Speed Control.
14. Reconfigurable T elltale Display • Power Steering System Over T emperature — If Equipped If the “POWER STEERING SYSTEM OVER TEMP” message and a icon are displayed on the EVIC screen, it indicates that extreme steer- ing maneuvers may have occurred, which caused an over temperature condition in the power steering system.
• Oil Pressure W arning Light This light indicates low engine oil pr essure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on.
requir ed. Y ou may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may requir e towing. • Oil T emperature W arning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
CAUTION! (Continued) “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned of f until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an autho- rized dealer for service.
1. Lane Departure W arning (LDW) The Lane Departure W arning (LDW) system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. • When the LDW system is ON and ready the lane lines and LDW indicator are the color gray .
If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir , it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electr onic Stability Control (ESC) system.
Operation of the Brake W arning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected.
Examples of this message type are “T urn Signal On” (if a turn signal is left on) and “Lights On” (if driver leaves the vehicle). • Unstor ed Messages Until RUN These messages deal primarily with the Remote Start feature. This message type is displayed until the ignition is in the RUN state.
9. Reconfigurable T elltale Area • Hill Descent Indicator — If Equipped The symbol illuminates (is armed) when the 4WD Low switch is activated and the transmis- sion range indicator is in LOW or REVERSE position (Off-Road Mode).
1 1. Instructional Area This area will display text to the visual warnings (i.e., “Push Brake T o Start”). 12. Amber Reconfigurable T elltale Display • T ransmission T emperature W arning Light This light indicates that there is excessive trans- mission fluid temperature that might occur with sever e usage such as trailer towing.
• Rear Axle Lock Indicator — If Equipped This light indicates when the rear axle lock has been activated. • Low Coolant Level Indicator This telltale will turn on to indicate the vehicle coolant level is low . • W indshield W asher Fluid Low Indicator This telltale will turn on to indicate the wind- shield washer fluid is low .
• LaneSense Service — If Equipped This telltale will turn on to indicate that the Lane Sense Departure has detected a failure. • Loose Fuel Filler Cap Message Indicator This telltale will turn on to indicate the fuel filler cap is loose.
• T emperature Gauge The temperature gauge shows engine coolant tem- perature. Any reading within the normal range indi- cates that the engine cooling system is operating satisfactorily . The gauge pointer will likely indicate a higher tem- perature when driving in hot weather , up mountain grades, or when towing a trailer .
14. Red Reconfigurable T elltale Display • Engine T emperature W arning Light This light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold.
NOTE: • Even if power steering assistance is no longer opera- tional, it is still possible to steer the vehicle. Under these conditions there will be a substantial incr ease in steering effort, especially at very low vehicle speeds and during parking maneuvers.
If jump starting is requir ed, refer to “Jump Starting Procedur es” in “What T o Do In Emergencies”. • Electr onic Throttle Control (ETC) Light This light informs you of a problem with the Electronic Thr ottle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check.
Unless r eset, this message will continue to display each time you turn the ignition switch to the ON/RUN position or cycle the ignition to the ON/RUN position if equipped with Keyless Enter-N-Go™. T o turn off the message temporarily , press and release the MENU but- ton.
SPress the ADAPTIVE CRUISE CONTROL (ACC) ON/ OFF button (located on the steering wheel) until one of the following displays in the EVIC: Adaptive Cruise Control Off When ACC is deactivated, the display will read “Adap- tive Cruise Contr ol Of f.
• Passenger Seatbelt Unbuckled • Service Airbag System • T raction Control Off • W asher Fluid Low • Oil Pressure Low • Oil Change Due • Fuel Low • Service Antilock Brake System • Se.
• Key in Ignition • Key in Ignition Lights On • Remote Start Active Key to Run • Remote Start Active Push Start Button • Remote Start Aborted Fuel Low • Remote Start Aborted T oo Cold • .
• T ransmission Cool Ready to Drive • Service T ransmission • Service Shifter • Engage Park Brake to Prevent Rolling • T ransmission T oo cold Idle with Engine On • W asher Fluid Low The Reconfigurable T elltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left.
T ransmission T emperature – Automatic T ransmission Only Oil T emp Coolant T emperature Oil Life Battery V oltage T ire Pressure Press and release the UP or DOWN arrow button until “T ire Pressure” is highlighted in the EVIC.
Fuel Economy Press and r elease the UP or DOWN arrow button until the Fuel Economy icon is highlighted. • A verage Fuel Economy/Miles Per Gallon (MPG or L/100 km with Bargraph) • Range T o Empty (.
Screen Setup Press and r elease the UP or DOWN arrow button until the Screen Setup display icon is highlighted in the EVIC. Press and release the OK button to enter the sub-menus. The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location that information is displayed.
Upper Right • None • Compass (default setting) • Outside T emp • Oil T emp • T ime • Range T o Empty (RTE) • A verage MPG • Curr ent MPG • T rip A • T rip B Restore T o Defaults (Restores All Settings T o Default Settings) • Cancel • Okay Center • None • Compass • Outside T emp.
• T rip B • Audio Information • Menu T itle (Default Setting) Uconnect® SETTINGS The Uconnect® system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access and change the customer programmable features.
Hard-Keys Hard-Keys are located below the Uconnect® system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instrument panel. T urn the control knob to scroll through menus and change settings (i.
Soft-Keys Soft-Keys are accessible on the Uconnect® display . Customer Programmable Features — Uconnect® 5.0/8.4 Settings Press the Apps soft-key , then pr ess the Settings soft-key to display the menu setting screen.
• Display Brightness With Headlights ON When in this display , you may select the brightness with the headlights on. Adjust the brightness with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back soft-key .
• T ouchscreen Beep When in this display , you may turn on or shut off the sound heard when a touch screen button (soft-key) is pressed. T ouch the T ouchscr een Beep soft-key until a check-mark appears next to the setting, showing that setting has been selected.
• Set T ime Minutes When in this display , you may adjust the minutes. The Sync with GPS T ime soft-key must be unchecked. T o make your selection, touch the + or - soft-keys to adjust the minutes up or down. T ouch the back arrow soft-key to return to the previous menu or touch the X soft-key to close out of the settings screen.
• Forward Collision W arning (FCW) Active Braking — If Equipped The FCW system includes Advanced Brake Assist (ABA). When this feature is selected, it will apply the brakes to slow your vehicle in case of potential forward collision.
• ParkSense® Active Park Assist — If Equipped The Rear Park Assist system will scan for objects behind the vehicle when the transmission shift lever is in RE- VERSE and the vehicle speed is less than 1 1 mph (18 km/h). The system can be enabled with Sound Only , or Sound and Display .
Refer to “ParkSense® Rear Park Assist” in “Understand- ing The Features Of Y our V ehicle” for system function and operating information. • T ilt Mirrors In Reverse — If Equipped When thi.
image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings” across the top of the scr een. After five seconds, this note will disappear .
setting, showing that setting has been selected. T ouch the back arrow soft-key to return to the previous menu. • Electric Park Brake Service Mode This feature provides a means for a technician or v.
The headlights will also turn off when the wipers are turned of f if they were turned on by this feature. T o make your selection, touch the Headlights W ith W ipers soft- key , until a check-mark appears next to setting, indicating that the setting has been selected.
• Flash Headlights With Lock When this feature is selected, the headlights will flash when the doors are locked or unlocked with the Remote Keyless Entry (RKE) transmitter . This feature may be selected with or without the sound horn on lock feature selected.
• Sound Horn With Remote Start When this feature is selected, the horn will sound when the remote start is activated. T o make your selection, touch the Sound Horn W ith Remote Start soft-key , until a check-mark appears next to setting, showing that setting has been selected.
return to the previous menu. Refer to “Keyless Enter-N- Go™” in “Things T o Know Before Starting Y our V ehicle”. • Memory T o FOB — If Equipped This featur e pr ovides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.
Seats soft-key , until a check-mark appears next to setting, showing that setting has been selected. T ouch the back arrow soft-key to return to the previous menu. Engine Off Options After pressing the Engine Off Options soft-key the fol- lowing settings will be available.
NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Laptop Computers and Radar Detectors. This is where the com- pass module is located, and it can cause interference with the compass sensor , and it may give false readings.
• Equalizer When in this display you may adjust the Bass, Mid and T reble settings. Adjust the settings with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back soft-key .
Radio Setup After pr essing the Radio Setup soft-key the following settings will be available. • T raf fic Announcement When this featur e is selected it allows the system to pause receivers and media to issue a traffic bulletin. T o change the T raffic Announcement setting touch the Off or On soft-key .
Clear Personal Data After pressing the Clear Personal Data Settings soft-key the following settings will be available: • Clear Personal Data When this feature is selected it will r emove personal data including Bluetooth® devices and pr esets. T o Clear Per - sonal Data touch the Y es or No soft-key .
Located in the front storage area, this feature allows an iPod® or external USB device to be plugged into the USB port. iPod® contr ol supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions may not fully support the iPod® control features.
Pressing the center button will make the radio switch between the various modes available (AM/FM/SXM/ CD/AUX, etc.). The left-hand control is a r ocker-type switch with a pushbutton in the center . The function of the left-hand control is dif ferent depending on which mode you are in.
CD/DVD DISC MAINTENANCE T o keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc.
CLIMA TE CONTROLS The air conditioning and heating system is designed to make you comfortable in all types of weather . This system can be operated thr ough either the controls on the instrument panel or through the Uconnect® system dis- play . When the Uconnect® system is in different modes (Ra- dio, Player , Settings, More, etc.
Front Blower Control There ar e seven blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position.
MAX A/C For maximum cooling, when MAX A/C is selected the A/C is turned on automatically and the air is recir culated. NOTE: A/C cannot be deselected when in MAX A/C position.
Bi-Level Mode Air is directed through the panel and floor outlets. NOTE: Ther e is a differ ence in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets.
Recirculation Control Press this button to choose between outside air intake or recir culation of the air inside the vehicle. A LED will illuminate when you are in Recirculation mode.
Economy Mode If ECONOMY mode is desired, press the A/C button to turn off the LED indicator and the A/C compressor . Rotate the temperature control knob to the desired tem- perature.
Soft-Keys Soft-keys are accessible on the Uconnect® system screen. Uconnect® 5.0 Manual T emperature Controls — Soft-keys Uconnect® 8.4 Manual T emperature Controls — Soft-keys 392 UNDERST ANDI.
Button Descriptions (Applies T o Both Hard-keys And Soft-keys) 1. MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window . Do not use abrasive window cleaners on the interior surface of the window . Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
7. Modes The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The Mode settings are as follows: • Panel Mode Air comes from the outlets in the instrument panel.
NOTE: The air conditioning compressor operates in MIX and DEFROST modes even if the A/C button is not pressed. This dehumidifies the air to help dry the wind- shield. T o impr ove fuel economy , use these modes only when necessary . 8. Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF .
Automatic Climate Controls With T ouch-Screen — If Equipped Hard-Keys The hard-keys located below the Uconnect® screen. Soft-Keys Soft-keys are accessible on the Uconnect® system screen. Uconnect® Automatic Climate Controls — Hard-keys Uconnect® 8.
Button Descriptions (Applies T o Both Hard-keys And Soft-keys) 1. MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
6. Rear Defrost Button Press and release this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the r ear window defr oster is on. The rear window defr oster automatically turns off after 10 minutes.
8. Passenger T emperature Control Down Button Provides the passenger with independent temperature control. Push the hard-key button for cooler temperature settings or on the touch-screen, press and slide the soft-key temperatur e bar towards the blue arrow soft-key for cooler temperature settings.
1 1. Modes The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The Mode settings are as follows: • Panel Mode Air comes from the outlets in the instrument panel.
12. Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF . 13. Driver T emperature Control Down Button Provides the driver with independent temperature con- trol.
NOTE: • If fog or mist appears on the windshield or side glass, select Defrost mode and increase blower speed. • If your air conditioning performance seems lower than expected, check the front of the A/C condenser (lo- cated in front of the radiator), for an accumulation of dirt or insects.
NOTE: In cold weather , use of Recir culation mode may lead to excessive window fogging. The recirculation feature may be unavailable (soft button greyed out) if conditions exist that could create fogging on the inside of the windshield.
NOTE: • It is not necessary to move the temperatur e settings for cold or hot vehicles. The system automatically adjusts the temperatur e, mode, and blower speed to provide comfort as quickly as possible. • The temperature can be displayed in U.S.
Operating Tips NOTE: Refer to the chart at the end of this section for suggested control settings for various weather condi- tions. Summer Operation The engine cooling system must be protected with a high-quality antifr eeze coolant to provide proper corro- sion protection and to protect against engine overheating.
NOTE: • Recir culate without A/C should not be used for long periods, as fogging may occur . • Automatic T emperature Contr ols (A TC) will automati- cally adjust the climate control settings to reduce or eliminate window fogging on the front windshield.
Control Setting Suggestions for V arious W eather Conditions 408 UNDERST ANDING YOUR INSTRUMENT P ANEL.
ST ARTING AND OPERA TING CONTENTS 䡵 ST AR TING PROCEDURES ............... .414 ▫ Normal Starting ...................... .414 ▫ Extr eme Cold W eather (Below –20°F Or −29°C) ............................ .415 ▫ Extended Park Starting .....
▫ SRear Electronic Locker (E-Locker) System – If Equipped .......................... .436 䡵 SELEC-TERRAIN™ .................... .437 ▫ Description ......................... .437 䡵 ON-ROAD DRIVING TIPS ............... .439 䡵 OFF-ROAD DRIVING TIPS .
▫ Electr onic Stability Control (ESC) ......... .466 ▫ ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light ............... .470 ▫ T railer Sway Control (TSC) .............. .471 ▫ Ready Alert Braking (RAB) .............. .472 ▫ Rain Brake Support (RBS) .
䡵 TIRE PRESSURE MONITOR SYSTEM (TPMS) . .500 ▫ Base System ........................ .503 ▫ Pr emium System – If Equipped ........... .506 ▫ General Information ................... 5 1 1 䡵 FUEL REQUIREMENTS .................. 5 1 1 ▫ Reformulated Gasoline .
▫ T owing This V ehicle Behind Another V ehicle . .534 ▫ Recr eational T owing — Front-Wheel Drive (FWD) Models ............................ .535 ▫ Recr eational T owing — 4WD Models with 1-Speed Power T ransfer Unit ................... .536 ▫ Recr eational T owing — 4WD Models with 2-Speed Power T ransfer Unit .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. W ARNING! • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
within 10 seconds, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedur e. T ip Start Feature T urn the ignition switch to ST AR T position and release it as soon as the starter engages.
If Engine Fails T o Start W ARNING! • Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury . • Do not attempt to push or tow your vehicle to get it started.
switch to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure. CAUTION! T o prevent damage to the starter , wait 10 to 15 seconds before trying again. After Starting The idle speed is controlled automatically and it will decrease as the engine warms up.
CAUTION! (Continued) • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift between P ARK, REVERSE, NEU- TRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear , make sure your foot is firmly pressing the brake pedal.
W ARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever .
Brake/T ransmission Shift Interlock System This vehicle is equipped with a Brake T ransmission Shift Interlock system (BTSI) that holds the shift lever in P ARK unless the brakes are applied.
Operation ⬙ in this section for further information). Mov- ing the shift lever into the ERS (-/+) position (beside the DRIVE position) displays the current gear in the instru- ment cluster , and pr events automatic upshifts beyond this gear .
When parking on a hill, apply the parking brake before shifting the transmission to P ARK, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the shift lever out of P ARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
W ARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into P ARK, turn the engine OFF , and remove the key fob.
CAUTION! • Before moving the shift lever out of P ARK, you must place the ignition from the LOCK/OFF posi- tion to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from P ARK or NEUTRAL into another gear range, as this can damage the drivetrain.
W ARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
If the transmission operating temperature exceeds nor- mal operating limits, the transmission controller may modify the transmission shift schedule, reduce engine torque, and/or expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating.
to operate. The Malfunction Indicator Light (MIL) may be illuminated. Limp Home Mode allows the vehicle to be driven to an authorized dealer for service without dam- aging the transmission. In the event of a momentary pr oblem, the transmission can be r eset to r egain all forwar d gears by performing the following steps: 1.
Moving the shift lever to the ERS position (beside DRIVE) will activate ERS mode, display the current gear in the instrument cluster , and maintain that gear as the top available gear . Once in ERS mode, moving the shift lever forwar d (-) or rearwar d (+) will change the top available gear .
Additionally , on dry pavement under heavy throttle input (where one may have no wheel spin), tor que will be sent to the rear in a pre-emptive ef fort to improve vehicle launch and performance characteristics. CAUTION! All wheels must have the same size and type tires.
2–Speed Four-Wheel Drive (4WD) — If Equipped The Four-Wheel Drive is fully automatic in the normal driving mode. The Selec-T errain buttons provide three selectable mode positions: • 4WD LOW •.
When additional traction is requir ed, the 4WD LOW range position can be used to provide an additional gear reduction which allows for increased torque to be deliv- ered to both the front and r ear wheels. 4WD LOW is intended for loose, slippery road surfaces only .
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the power transfer unit in the NEUTRAL (N) position without first fully engag- ing the parking brake.
NOTE: If shift conditions/interlocks are not met a mes- sage will flash from the Electronic V ehicle Information Center (EVIC) with instructions on how to complete the requested shift. Refer to “Electronic V ehicle Information Center (EVIC)” in “Understanding Y our Instrument Panel” for further information.
• Shifting into or out of 4WD LOW is possible with the vehicle completely stopped; however , difficulty may occur due to the mating clutch teeth not being pr op- erly aligned. Several attempts may be requir ed for clutch teeth alignment and shift completion to occur .
6. Using a ballpoint pen or similar object, pr ess and hold the recessed power transfer unit NEUTRAL (N) button (lo- cated above the selector switch) for four seconds. The light behind the NEUTRAL (N) symbol will blink, indi- cating shift in progr ess.
Rear Electronic Locker (E-Locker) System – If Equipped The Rear E-Locker System features a mechanical locking rear differential to provide better traction in the 4WD LOW position. The “REAR LOCK” button is on the Selec-T errain Knob. Activating the Rear E-Locker T o activate the Rear E-Locker System, the following conditions must be met: 1.
• When disengaging Rear E-Locker , the indicator lights in the instrument cluster and on the REAR LOCK button will begin to flash. When the shift is complete the REAR LOCK indicator lights will remain off.
Selec-T errain™ offers the following modes: • Auto – Fully automatic full time four-wheel drive operation can be used on and off road. Balances traction with seamless steering feel to provide im- proved handling and acceleration over two-wheel drive vehicles.
• Rock – Off-r oad calibration only available in 4WD LOW range. T raction based tuning with improved steer-ability for use on high traction off-r oad surfaces. Use for low speed obstacles such as large rocks, deep ruts, etc. NOTE: Rock mode is only available on the vehicles equipped with the Off-Road package.
OFF-ROAD DRIVING TIPS When T o Use 4WD LOW Range When off-r oad driving, shift to 4WD LOW for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low-speed pulling power (Refer to “All Wheel Drive and Four-Wheel Drive Operation” in this section for further details).
Flowing W ater If the water is swift flowing and rising (as in storm run-of f) avoid crossing until the water level r ecedes and/or the flow rate is r educed. If you must cross flowing-water , avoid depths in excess of 9 inches (22 cm). The flowing water can erode the streambed causing your vehicle to sink into deeper water .
A void abrupt downshifts on icy or slippery r oads be- cause engine braking may cause skidding and loss of control. Hill Climbing NOTE: Befor e attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the 4WD System to 4WD LOW .
T raction Downhill Shift the transmission into a low gear and the 4WD System to 4WD LOW range or Select Hill Descent Control if equipped (refer to ⬙ Electronic Brake Control System ⬙ in this section for further information. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag.
W ARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. Y ou might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary .
NOTE: • Even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers.
T o apply the parking brake manually , pull up on the switch momentarily . Y ou may hear a slight whirring sound from the back of the vehicle while the parking brake engages. Once the parking brake is fully engaged, The BRAKE warning lamp in the instrument cluster and an indicator on the switch will illuminate.
T o release the park brake manually , the ignition switch must be ON. Put your foot on the brake pedal, then push the parking brake switch down momentarily . Y ou may hear a slight whirring sound from the back of the car while the parking brake disengages.
W ARNING! (Continued) • Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with Keyless Enter-N- Go™ in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
reaches appr oximately 3 mph, the parking brake will remain engaged. W ARNING! Driving the vehicle with the parking brake engaged, or repeated use of the parking brake to slow the vehicle may cause serious damage to the brake sys- tem. In the unlikely event of a malfunction of the Electric Park Brake system, a yellow EPB fault lamp will illuminate.
Safehold can be temporarily bypassed by pressing the Electric Park Brake Switch while the driver door is open. Once manually bypassed, Safehold will be enabled again once the vehicle reaches 12 mph (20 km/h) or the ignition is turned to the OFF position and back to ON again.
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
W ARNING! • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer .
• Engines may idle at higher speeds during warm-up, which could cause rear wheels to spin and result in loss of vehicle contr ol. Be especially careful while driving on slippery roads, in close-quarter maneuver- ing, parking, or stopping. • Do not drive too fast for road conditions, especially when r oads are wet or slushy .
Anti-Lock Brake System (ABS) This system aids the driver in maintaining vehicle contr ol under adverse braking conditions. The system controls hydraulic brake pr essure to pr event wheel lock-up to help avoid skidding on slippery surfaces during braking.
or the “Full Off” mode. Refer to “Electronic Stability Control (ESC)” in this section for further information. Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emer gency braking maneuvers.
applies the appropriate brake and may also reduce engine power to lessen the chance that wheel lift will occur . ERM will only intervene during very severe or evasive driving maneuvers. ERM can only r educe the chance of wheel lift occurring during severe or evasive driving maneuvers.
The following conditions must be met in or der for HSA to activate: • The vehicle must be stopped. • The vehicle must be on a 7% (approximate) grade or greater hill. • The gear selection must match vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backing uphill is in REVERSE gear).
T owing With HSA HSA will provide assistance during acceleration on an incline while towing a trailer . W ARNING! • If you use a trailer brake controller with your trailer , the trailer brakes may be activated and deactivated with the brake switch.
Hill Descent Control (HDC) — If Equipped HDC is intended for low speed off road driving while in 4WD Low Range. HDC maintains vehicle speed while descending hills during various driving situations. HDC controls vehicle speed by actively controlling the brakes.
Activating HDC Once HDC is enabled it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for HDC is selectable by the driver , and can be adjusted by using the gear shift lever . The following summarizes the HDC set speeds: • P = No set speed.
Deactivating HDC HDC will be deactivated but remain available if any of the following conditions occur: • Driver overrides HDC set speed with throttle or brake application.
• The cluster icon and switch lamp will flash for several seconds then extinguish when the driver presses the HDC switch but enable conditions are not met. • The cluster icon and switch lamp will flash for several seconds then extinguish when HDC deactivates due to excess speed.
Enabling SSC SSC is enabled by pr essing the SSC switch, but the following conditions must also be met to enable SSC: • Driveline is in 4WD Low Range • V ehicle speed is below 5 mph • Parking br.
• 7th= 4.3 mph (7 km/h) • 8th = 5 mph (8 km/h) • 9th = 5.6 mph (9 km/h) • REVERSE = .6 mph (1 km/h) • NEUTRAL = 1.2 mph (2 km/h) • P ARK = SSC remains enabled but not active NOTE: These SSC default set speeds are dependent on hill grade.
Deactivating SSC SSC will be deactivated but remain available if any of the following conditions occur: • Driver overrides SSC set speed with throttle or brake application. • V ehicle speed exceeds 20 mph but remains below 40 mph. • V ehicle is shifted to park.
• The cluster icon and switch lamp will flash for several seconds then extinguish when the driver presses the SSC switch but enable conditions are not met. • The cluster icon and switch lamp will flash for several seconds then extinguish when SSC deactivates due to excess speed.
The “ESC Activation/Malfunction Indicator Light” lo- cated in the instrument cluster will start to flash as soon as the tires lose traction and the ESC system becomes active. The “ESC Activation/Malfunction Indicator Light” also flashes when the TCS is active.
ESC On – T wo-Wheel Drive V ehicles And Four-Wheel Drive V ehicles In 2WD And 4WD High Range This is the normal operating mode for ESC when oper- ating a two-wheel drive vehicle. It is also the normal mode for operating a four-wheel drive vehicle in 2WD or 4WD HIGH range.
W ARNING! • When in “Partial Off” mode, the TCS functionality of ESC, (except for the limited slip feature de- scribed in the TCS section), has been disabled and the “ESC Off Indicator Light” will be illuminated.
NOTE: • “Full Off” is the only operating mode for ESC in 4WD LOW range. The ESC system will be in this mode whenever the vehicle is started in 4WD LOW range or the power transfer unit is shifted into 4WD LOW range.
speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the pr oblem diagnosed and corrected. The “ESC Activation/Malfunction Indicator Light” (lo- cated in the instrument cluster) starts to flash as soon as the tir es lose traction and the ESC system becomes active.
appropriate wheel(s) to counteract the sway of the trailer . TSC will become active automatically once an excessively swaying trailer is recognized. Always use caution when towing a trailer and follow the trailer tongue weight recommendations.
Rain Brake Support (RBS) Rain Brake Support may improve braking performance in wet conditions. It will periodically apply a small amount of brake pressur e to r emove any water buildup on the front brake r otors. It is trigger ed by the windshield wiper setting and only functions when they are in use.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standar ds. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • Eur opean-Metric tire sizing is based on European design standards.
• T emporary spare tires are designed for temporary emergency use only . T emporary high pr essure com- pact spare tires have the letter “T” or “S” molded into the sidewall preceding the size designation. Example: T145/80D18 103M. • High flotation tire sizing is based on U.
EXAMPLE: 10.5 = Section width in inches (in) R = Construction code — ⬙ R ⬙ means radial construction — ⬙ D ⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service De.
EXAMPLE: Load Identification: ⴖ ....blank.... ⴖ = Absence of any text on the sidewall of the tire indicates a Standard Load (SL) tire Extra Load (XL) = Extra load (or reinfor ced) tire Light Load .
EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of T ransportation — This symbol certifies that the tire is in compliance with the U.S. Department of T ransportation tire safety standards and is appro.
Tire T erminology And Definitions T erm Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door . Cold T ire Inflation Pressure Cold tire inflation pressure is defined as the tire pressur e after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
Tire Loading And Tire Pressure T ire And Loading Information Placard Location NOTE: The proper cold tir e inflation pressure is listed on the driver ’s side B-Pillar or the rear edge of the driver’s side door .
T ire And Loading Information Placard This placard tells you important information about the: 1) Number of people that can be carried in the ve- hicle. 2) T otal weight your vehicle can carry . 3) T ire size designed for your vehicle. 4) Cold tire inflation pressures for the front, rear , and spare tires.
Loading The vehicle maximum load on the tir e must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the load.
4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in .
484 ST ARTING AND OPERA TING.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pressur es can cause uneven wear pat- terns to develop across the tire tr ead.
• Inspect tires for signs of tire wear or visible damage. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
loading may be requir ed for high-speed vehicle opera- tion. Refer to your authorized tire dealer or original equipment vehicle dealer for recommended safe operat- ing speeds, loading and cold tire inflation pressures. W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous.
• The puncture is no greater than ¼ ⬙ (6 mm). Consult an authorized tire dealer for tir e repairs and additional information. Damaged Run Flat tir es, or Run Flat tir es that have experienced a loss of pressure should be replaced imme- diately with another Run Flat tire of identical size and service description (Load Index and Speed Code).
If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle.
Spare Tires – If Equipped NOTE: For vehicles equipped with TIREFIT instead of a spare tire, please refer to “TIREFIT KIT” in “What T o Do In Emergencies” for further information.
wheel is designed specifically for the compact spare tire. Do not install mor e than one compact spare tir e and wheel on the vehicle at any given time. W ARNING! Compact spares are for temporary emergency use only . With these spares, do not drive more than 50 mph (80 km/h).
W ARNING! Limited-use spares are for emergency use only . In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel.
These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tr ead depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tir e should be replaced. Refer to “Replacement T ires” in this section for further infor- mation.
W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose control and have a collision resulting in serious injury or death.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
• Use on Front T ires Only • Due to limited clearance, the following traction de- vices are recommended: Front Wheel Drive (FWD) Models • Original equipment 225/60R17 and 225/55R18 tire sizes are not chainable. • The use of 7mm snow chains is permitted with the use of 215/60R17 tires on size 17 x 7.
CAUTION! (Continued) • Damage to Four Wheel Drive (4WD) T railhawk Models may result if tire chains or traction devices are used with original equipment size tires. W ARNING! Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling.
TIRE ROT A TION RECOMMENDA TIONS The tires on the front and rear of your vehicle operate at differ ent loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates. These ef fects can be reduced by timely rotation of tir es.
CAUTION! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause (Continued) CAUTION! (Continued) damage to the power transfer unit. T ire rotation schedule should be followed to balance tire wear .
in “Starting and Operating” for information on how to properly inflate the vehicle’s tires. The tire pressure will also increase as the vehicle is driven.
CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
• Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tir e failure. Under-inflation also r educes fuel ef ficiency and tire tread life, and may affect the vehicle’s handling and stopping ability .
T ire Pressure Monitoring Low Pressure W arnings The “T ire Pressur e Monitoring T elltale Light” will illuminate in the instrument cluster , a “LOW TIRE PRESSURE” message will display in the .
4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPMS sensors. V ehicles With Full-Size Spare 1. The matching full-size spare wheel and tire assembly has a tire pressure monitoring sensor that can be monitored by the TPMS. 2.
5. Once you r epair or r eplace the original r oad tire and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically and the “TPMS T elltale Light” will turn off, as long as no tire pressur e is below the low-pressure warning limit in any of the four active r oad tires.
T ire Pressure Monitoring Low Pressure W arnings The “T ire Pressur e Monitoring T elltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires.
values in the graphic display in the EVIC will return to their original color , and the “T ire Pr essure Monitoring T elltale Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15.5 mph (25 km/h) in order for the TPMS to receive this information.
If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “T ire Pressure Monitoring T elltale Light” will no longer flash, and the “SER VICE TPM SYSTEM message will no longer display , and a pressur e value will display in place of the dashes.
4. The EVIC will display a graphic showing the tire pressur e value in the same color as the other pressure values in place of the different color low tire pressure value. The EVIC will also display a “SP ARE LOW PRESSURE” message to remind you to service the flat tire.
low-pressur e warning limit in any of the four active road tir es. The vehicle may need to be driven for up to 20 minutes above 15.5 mph (25 km/h) in order for the TPMS to receive this information. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada.
consistent gasoline specifications (the W orldwide Fuel Charter , WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and dura- bility for your vehicle. The manufacturer recommends the use of gasoline that meet the WWFC specifications if they are available.
Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as Ethanol. Fuels blended with oxygenates may be used in your vehicle. CAUTION! DO NOT use gasoline containing Methanol or gaso- line containing more than 10% Ethanol.
• Disconnect and reconnect the battery to reset the engine controller memory . More extensive r epairs will be required for pr olonged exposure to E-85 fuel. MMT In Gasoline MMT (Methylcyclopentadienyl Manganese T ricarbonyl) is a manganese-containing metallic additive that is blended into some gasoline to increase octane.
CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate ser- vice.
W ARNING! (Continued) • Guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly . Until repaired, drive with all side windows fully open.
2. Open the fuel filler door , and remove the fuel filler cap. NOTE: • In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.
W ARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the MIL to turn on.
VEHICLE LOADING Certification Label As required by National Highway T raffic Safety Admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar .
T ire Size The tire size on the V ehicle Certification Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tire size listed.
items down low and be sure that the weight is distributed equally . Stow all loose items securely before driving. Improper weight distributions can have an adverse ef fect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR.
exceed the GVWR. Refer to “V ehicle Loading/V ehicle Certification Label” in “Starting and Operating” for further information. Gross T railer W eight (GTW) The GTW is the weight of the trailer.
W ARNING! It is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if either rating is exceeded. Y ou could lose control of the vehicle and have a collision. T ongue W eight (TW) The tongue weight is the downward force exerted on the hitch ball by the trailer .
W eight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s fr ont axle and the trailer axle(s).
T railer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ T ransmission Model Frontal Area Maximum GTW (Gross T railer Wt.) Maximum T ongue Wt.
T railer And T ongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% to 15% of the Gross T railer W eight (GTW) on the tow hitch of your vehicle.
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
W ARNING! (Continued) • When hauling cargo, or towing a trailer , do not overload your vehicle or trailer . Overloading can cause a loss of control, poor performance, or dam- age to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.
• Check the trailer tires for proper tire inflation pres- sures before trailer usage. • Check for signs of tir e wear or visible tire damage before towing a trailer . Refer to “T ir es – General Information” in “Starting and Operating” for the proper inspection procedure.
W ARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. Y ou might not have brakes when you need them and could have a collision. • T owing any trailer will increase your stopping distance.
Four-Pin Connector 1 — Female Pins 4 — Park 2 — Male Pin 5 — Left Stop/T urn 3 — Ground 6 — Right Stop/T urn Seven-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 — Left St.
T owing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away fr om heavy traffic. Automatic T ransmission - If Equipped The DRIVE range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing.
RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) T owing This V ehicle Behind Another V ehicle 4WD Models T owing Condition Wheel OFF the Ground Front-Wheel Drive (FWD) Models 1-Speed Power T ransfer Uni.
Recreational T owing — Front-Wheel Drive (FWD) Models Automatic T ransmission - If Equipped DO NOT flat tow this vehicle. Damage to the drivetrain will result. Recreational towing of automatic transmission vehicles is allowed ONL Y if the front wheels ar e OFF the ground.
CAUTION! T owing this vehicle in violation of the above require- ments can cause severe engine and/or transmission damage. Damage from improper towing is not cov- ered under the New V ehicle Limited W arranty . Recreational T owing — 4WD Models with 1-Speed Power T ransfer Unit Recreational towing is not allowed.
CAUTION! • DO NOT dolly tow any 4WD vehicle. Internal damage to the transmission or power transfer unit will occur if a dolly is used when recreational towing. • T ow only in a forward direction. T owing this ve- hicle backwards can cause severe damage to the power transfer unit.
W ARNING! (Continued) position disengages both the front and rear drive- shafts from the powertrain and will allow the vehicle to move, even if the transmission is in P ARK. The parking brake should always be applied when the driver is not in the vehicle.
7. After the shift is completed and the NEUTRAL (N) light stays on, release the NEUTRAL (N) button. 8. Start the engine. 9. Shift the transmission into REVERSE. 10. Release the brake pedal for five seconds and ensur e that there is no vehicle movement.
NOTE: • Steps 1 through 5 are requirements that must be met prior to pressing the NEUTRAL (N) button, and must continue to be met until the shift has been completed.
6. Using a ballpoint pen or similar object, press and hold the recessed power transfer unit NEUTRAL (N) button (located by the selector switch) for one second.
13. Pr ess and hold the brake pedal. 14. Release the parking brake. 15. Shift the transmission into DRIVE, release the brake pedal, and check that the vehicle operates normally . NOTE: • Steps 1 through 5 are requirements that must be met prior to pressing the NEUTRAL (N) button, and must continue to be met until the shift has been completed.
WHA T TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD W ARNING FLASHERS .......... .545 䡵 IF YOUR ENGINE OVERHEA TS ........... .545 䡵 WHEEL AND TIRE TORQUE SPECIFICA TIONS ..................... .546 ▫ T orque Specifications ................. .546 䡵 TIREFIT KIT — IF EQUIPPED .
䡵 T OWING A DISABLED VEHICLE .......... .575 ▫ Fr ont-Wheel Drive (FWD) Models ........ .577 ▫ 4x4 Models W ith 1–Speed Power T ransfer Unit ........................ .578 ▫ 4x4 Models W ith 2–Speed Power T ransfer Unit ....................
HAZARD W ARNING FLASHERS The Hazard W arning flasher switch is located in the switch bank below the radio screen. Press the switch to turn on the Hazard W arning flasher . When the switch is activated, all dir ec- tional turn signals will flash on and off to warn oncoming traffic of an emergency .
NOTE: Ther e are steps that you can take to slow down an impending overheat condition: • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.
T ighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt tor que to be sure that all the lug nuts/bolts are properly seated against the wheel.
W ARNING! T o avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury . TIREFIT KIT — IF EQUIPPED Small punctures up to 1/4 in (6 mm) in the tire tread can be sealed with TIREFIT .
TIREFIT Kit Components And Operation 1. Sealant Bottle 2. Deflation Button 3. Pr essure Gauge 4. Power Button 5. Mode Select Knob 6. Sealant Hose (Clear) 7. Air Pump Hose (Black) 8. Power Plug Using The Mode Select Knob And Hoses Y our TIREFIT kit is equipped with the following symbols to indicate the air or sealant mode.
Selecting Sealant Mode T urn the Mode Select Knob (5) to this position to inject the TIREFIT Sealant and to inflate the tire. Use the Sealant Hose (clear hose) (6) when selecting this mode. Using The Power Button Push and release the Power Button (4) once to turn On the TIREFIT kit.
• For optimum performance, make sur e the valve stem on the wheel is free of debris before connecting the TIREFIT kit. • Y ou can use the TIREFIT air pump to inflate bicycle tires.
W ARNING! (Continued) • Keep TIREFIT away from open flames or heat source. • A loose TIREFIT kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position befor e proceed- ing. 3. Place the transmission in P ARK (auto transmission) or in Gear (manual transmission) and turn Of f the igni- tion.
NOTE: Sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow withi n0–1 0 seconds through the Sealant Hose (6): 1. Pr ess the Power Button (4) to turn Off the TIREFIT kit. Disconnect the Sealant Hose (6) fr om the valve stem.
If the tire does not inflate to at least 26 psi (1.8 Bar) pressure within 15 minutes: • The tir e is too badly damaged. Do not attempt to drive the vehicle further . Call for assistance. NOTE: If the tire becomes over-inflated, press the Defla- tion Button to reduce the tire pr essure to the recom- mended inflation pressur e before continuing.
(D) Drive V ehicle: Immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the TIREFIT Sealant within the tire. Do not exceed 55 mph (88 km/h). W ARNING! TIREFIT is not a permanent flat tire repair .
If the tire pressure is 19 psi (1.3 Bar) or higher: 1. Pr ess the Power Button (4) to turn on TIREFIT and inflate the tire to the pr essure indicated on the tire and loading information label on the driver-side door opening.
5. Position the new Sealant Bottle (1) in the housing so that the Sealant Hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the housing.
W ARNING! (Continued) • The jack is designed to be used as a tool for changing tires only . The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only . A void ice or slippery areas.
4. Remove the chocks. 5. Remove the scissors jack and wheel bolt wrench from the spare wheel as an assembly . T urn the jack screw to the left to loosen the wheel bolt wrench, and remove the wrench from the jack assembly . NOTE: The jack handle attaches to the side of the jack with two attachment points.
W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately .
Jacking Instructions W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the spare tire, jack, and wheel bolt wrench.
Jacking Locations Rear Jacking Location 564 WHA T TO DO IN EMERGENCIES.
Rear Jacking Engagement Point Front Jacking Location 6 WHA T TO DO IN EMERGENCIES 565.
5. Raise the vehicle just enough to remove the flat tire. W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip of f the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire.
NOTE: • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • Refer to “Compact Spare T ire” and to “Limited-Use Spare” under “T ires—.
10. Lower the vehicle to the gr ound by turning the jack handle counterclockwise. 1 1. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for incr eased leverage. T ighten the wheel bolts in a star pattern until each wheel bolt has been tightened twice.
W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately .
5. After 25 miles (40 km) check the wheel bolt torque with a torque wr ench to ensure that all wheel bolts are properly seated against the wheel. JUMP-ST ARTING PROCEDURES If your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack.
W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. Y ou can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.
CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle.
8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery . 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle.
Use the least amount of accelerator pedal pressur e that will maintain the rocking motion without spinning the wheels or racing the engine. NOTE: Press the ⬙ ESC Off ⬙ switch (if necessary), to place the Electronic Stability Control (ESC) system in ⬙ Partial Off ⬙ mode, befor e rocking the vehicle.
W ARNING! (Continued) even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed.
4X4 MODELS T owing Condition Wheels OFF the Ground FWD MOD- ELS 1–SPEED POWER TRANSFER UNIT 2–SPEED POWER TRANSFER UNIT Flat T ow NONE NOT AL- LOWED NOT ALLOWED See instructions under “Recreatio.
Proper towing or lifting equipment is r equired to pr event damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer ’s instructions.
CAUTION! T owing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- age from improper towing is not covered under the New V ehicle Limited W arranty . 4x4 Models With 1–Speed Power T ransfer Unit The manufacturer requires towing with all four wheels OFF the ground.
4x4 Models With 2–Speed Power T ransfer Unit The manufacturer r ecommends towing with all four wheels OFF the ground. Acceptable methods ar e to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly .
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMP ARTMENT — 2.4L ......... .583 䡵 ENGINE COMP ARTMENT — 3.2L ......... .584 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .585 ▫ Loose Fuel Filler Cap Message ........... .586 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS .
▫ Brake System ....................... .609 ▫ Automatic T ransmission ................ 6 1 1 ▫ Sky Slider™ T op Care ................. .613 ▫ Appearance Care And Protection From Corrosion .......................... .615 䡵 FUSES ...........
ENGINE COMP ARTMENT — 2.4L 1 — Air Cleaner Filter 5 — Power Distribution Center (Fuses) 2 — Engine Coolant Pressure Cap 6 — Battery 3 — Oil Fill Cap 7 — W asher Fluid Reservoir 4 — Bra.
ENGINE COMP ARTMENT — 3.2L 1 — Engine Coolant Reservoir 5 — W asher Fluid Reservoir 2 — Engine Oil Filter Access Cover 6 — Battery 3 — Brake Fluid Reservoir 7 — Engine Oil Fill 4 — Pow.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gASCAP” message will display in the odometer or a “CHECK gASCAP” message will be displayed in the Electronic V ehicle Information Center (EVIC).
Y our vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. T o check if your vehicle’s OBD II system is ready , you must do the following: 1. Cycle the ignition switch to the ON position, but do not crank or start the engine.
REPLACEMENT P ARTS Use of genuine MOP AR® parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-MOP AR® parts for mainte- nance and r epairs will not be cover ed by the New V ehicle Limited W arranty .
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed “Maintenance Schedule”, there are other components which may r equire servicing or replacement in the future.
regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine.
Engine Oil V iscosity (SAE Grade) – 3.2L Engine MOP AR® SAE 5W -20 engine oil or equivalent Pennzoil® or Shell Helix® is recommended for all operating tem- peratures. This engine oil improves low temperature starting and vehicle fuel economy . The engine oil filler cap also shows the recommended engine oil viscosity for your engine.
NOTE: For best access to the oil filter , a drive on hoist should be used instead of a chassis hoist. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type dispos- able oil filter . Use a filter of this type for r eplacement.
Maintenance-Free Battery Y our vehicle is equipped with a maintenance-free battery . Y ou will never have to add water , nor is periodic main- tenance requir ed. W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing.
CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case.
W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
However , the manufacturer recommends that air condi- tioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. NOTE: Use only manufactur er approved A/C system P AG compressor oil, and refrigerants.
Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner . This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
NOTE: The rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder .
5. Lower the wiper blade and snap the pivot cap into place. Adding W asher Fluid The windshield and rear window washers shar e the same fluid reservoir . The fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level in the reservoir at r egular intervals.
have an authorized technician inspect the complete ex- haust system and adjacent body areas for br oken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
CAUTION! (Continued) • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly .
• Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions. Cooling System W ARNING! Y ou or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator .
W ith the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of engine coolant (antifreeze) from the radiator drain cock. If the cap is sealing properly , the engine coolant (anti- freeze) will begin to drain from the coolant recovery bottle.
CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive T echnology (OA T) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
the same engine coolant (OA T coolant conforming to MS-12106) throughout the life of your vehicle. Please review these recommendations for using Organic Additive T echnology (OA T) engine coolant (antifreeze) that meets the requirements of Chrysler Material Stan- dard MS-12106.
Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
Disposal Of Used Engine Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring pr oper disposal. Check with your local authorities to determine the disposal rules for your community .
If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant expansion bottle. • Check the coolant freeze point in the radiator and in the coolant expansion bottle.
W ARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou would not have your full braking capacity in an emergency .
W ARNING! (Continued) • T o avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container . Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point.
CAUTION! Using a transmission fluid other than the manufac- turer ’ s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications.
CAUTION! If a transmission fluid leak occurs, visit your autho- rized dealer immediately . Severe transmission dam- age may occur . Y our authorized dealer has the proper tools to adjust the fluid level accurately .
General Cleaning Careful vacuuming of the top before washing is helpful in removing dust and other foreign particles. If Hand W ashing: • W ash in partial shade instead of direct sun.
Additional Cleaning Procedure For additional cleaning assistance in removing stubborn stains, apply MOP AR® Convertible Cloth T op Cleaner or equivalent to the complete stain, extending 2 inches (50 mm) beyond the stain. W ith a soft bristle brush, scrub in all directions over the stain.
road surfaces on which the vehicle is operated, extr eme hot or cold weather and other extreme conditions will have an adverse ef fect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.
CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
Wheel And Wheel T rim Care • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • T o r emove heavy soil and/or excessive brake dust, use MOP AR® Wheel Cleaner .
• For tough stains, apply MOP AR® T otal Clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply MOP AR® Multi-Purpose Cleaner to a clean, damp cloth and remove stain.
solvents, detergents, or ammonia-based cleaners to clean leather upholstery . Application of a leather conditioner is not requir ed to maintain the original condition. W ARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
When cleaning the rear view mirror , spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror . Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic.
W ARNING! (Continued) • Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged.
Cavity Blade Fuse Cartridge Fuse Description F06 — — Not Used F07 15 Amp Blue — Powertrain Control Module - PCM F08 25 Amp Clear — Engine Control Module (ECM) F09 — — Not Used F10 20 Amp Y.
Cavity Blade Fuse Cartridge Fuse Description F21 — — Not Used F22 5 Amp Ta n — Radiator Fan F23 70 Amp Ta n — Body Controller Module (BCM) - Feed 1 F24 — — Not Used F25 — — Not Used F2.
Cavity Blade Fuse Cartridge Fuse Description F38 — 60 Amp Y ellow Glow Plugs - Diesel Only - If Equipped F39 — 40 Amp Green HV AC Blower Motor F40 — 20 Amp Blue T railer T ow Park Light - If Equ.
Cavity Blade Fuse Cartridge Fuse Description F50 — 30 Amp Pink Power Liftgate - If Equipped F51 — — Not Used F52 — — Not Used F53 — 30 Amp Pink BSM-ECU & V alves F54 — 30 Amp Pink Ur.
Cavity Blade Fuse Cartridge Fuse Description F57 20 Amp Y ellow — Fuel Pump Motor F58 10 Amp Red — Occupant Classifica- tion Module F59 — — Not Used F60 20 Amp Y ellow — Power Outlet - Cen- .
Cavity Blade Fuse Cartridge Fuse Description F67 — — Not Used F68 — — Not Used F69 10 Amp Red — Power T ransfer Unit Switch (TSBM) / Active Grill Shutter (AGS) - If Equipped F70 — — Not .
Cavity Blade Fuse Cartridge Fuse Description F77 10 Amp Red — Fuel Door Release/ Brake Pedal Switch F78 10 Amp Red — Diagnostic Port / Steering Column Control Module (SCCM) / Digital TV - If Equip.
Cavity Blade Fuse Cartridge Fuse Description F88 15 Amp Blue — Collision Mitigation Module (CMM) / Electrochr omatic Mirror / Smart Camera Module - If Equipped F89 10 Amp Red — Headlamp Leveling -.
Cavity Blade Fuse Cartridge Fuse Description F97 10 Amp Red — Occupant Restraint Controller (ORC) F98 25 Amp Clear — Audio Amplifier - If Equipped F99 — 30 Amp Pink T railer T ow Module - If Equ.
Cavity Blade Fuse Description F51 10 Amp Red Driver W indow Switch/ Power Mirrors – If Equipped F53 7.5 Amp Brown UCI Port (USB & AUX) F89 10 Amp Red Door Locks – Driver Un- lock F91 7.
REPLACEMENT BULBS Interior Bulbs Bulb Number Cargo Lamp TL212–2 Overhead Console Lamp PL W214–2A Reading Lamp WL212–2 Exterior Bulbs Bulb Number Low Beam/High Beam (Bi-Halogen) Headlamps HIR2 Lo.
BULB REPLACEMENT NOTE: Lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor . T urning the lamps on will usually accelerate the clearing process.
3. Firmly grasp the cap and rotate it counterclockwise to unlock it. 4. Firmly grasp the bulb and connector assembly and rotate counterclockwise to remove from the housing. 5. Disconnect the bulb from the electrical connector and then connect the replacement bulb.
4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Re-install air cleaner filter housing, if removed. Front Fog Lamp 1. Unlock lower access door in wheel liner . 2. Reach behind the fog lamp housing to access the bulb.
3. Squeeze the two tabs on the side of the bulb socket and pull straight out from the fog lamp. 4. Disconnect the wire harness from the bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
Back-up Lamp 1. Open the liftgate. 2. Use a fiber stick or flat blade scr ew driver to pry the lower trim from the liftgate. 3. Once the trim is loose, pull it back exposing the trim panel. 4. Using a fiber stick or flat blade screw driver , open the trim panel exposing the back of the liftgate lamp.
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 2.4L and 3.2L Engines 15.8 Gallons 60 Liters Engine Oil W ith Filter 2.4 Liter Engine (SAE 0W -20, API Certified) 5.5 Quarts 5.2 Liters 3.2 Liter Engine (SAE 5W -20, API Certified) 6 Quarts 5.6 Liters Cooling System* 2.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant W e recommend you use MOP AR® Antifreeze/Coolant 10 Y ear/150,000 Mile Formula OA T (Or ganic Additive T echnology) or equivalent meeting the require- ments of Chrysler Material Standard MS-12106.
Component Fluid, Lubricant, or Genuine Part Spark Plugs – 2.4L Engine W e recommend you use MOP AR® Spark Plugs (Gap 0.047 in [1.2 mm]) Spark Plugs – 3.2L Engine W e recommend you use MOP AR® Spark Plugs (Gap 0.043 in [1.1 mm]) Fuel Selection – 2.
.
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE ............ .644 ▫ Maintenance Chart .................... .646 8 M A I N T E N A N C E S C H E D U L E S.
MAINTENANCE SCHEDULE Y our vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate.
Severe Duty All Models Change Engine Oil at 4000 miles (6,500 km) if the vehicle is operated in a dusty and off road environment. This type of vehicle use is considered Severe Duty Once A Month Or Before A Long T rip: • Check engine oil level • Check windshield washer fluid level • Check tire pressur e and look for unusual wear or damage.
Maintenance Chart Refer to the Maintenance Schedules on the following pages for the requir ed maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 7.
Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or.
W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 SUGGESTIONS FOR OBT AINING SER VICE FOR YOUR VEHICLE ...................... .651 ▫ Pr epare For The Appointment ............ .651 ▫ Pr epare A List ....................... .651 ▫ Be Reasonable W ith Requests .
䡵 DEP AR TMENT OF TRANSPOR T A TION UNIFORM TIRE QUALITY GRADES ................ .657 ▫ T readwear .......................... .657 ▫ T raction Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you are having warranty work done, be sure to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
W arranty service must be done by an authorized dealer. W e str ongly r ecommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get pr ompt and high quality service.
Chrysler Group LLC Customer Center P .O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: (877) 426–5337 Chrysler Canada Inc. Customer Center P .O. Box 1621 W indsor , Ontario N9A 4H6 Phone: (800) 465–2001 English / (800) 387–9983 French In Mexico Contact: A v .
expires. The manufacturer stands behind only the manu- facturer’s service contracts. If you purchased a manufac- turer’s service contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of the vehicle delivery date.
W ARRANTY INFORMA TION See the W arranty Information Booklet, located on the DVD, for the terms and provisions of Chrysler Group LLC warranties applicable to this vehicle and market. MOP AR® P ARTS MOP AR® fluids, lubricants, parts, and accessories ar e available from an authorized dealer .
In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department imme- diately . Canadian customers who wish to report a safety defect to the Canadian government should contact T rans- port Canada, Motor V ehicle Defect Investigations and Recalls at 1-800-333-0510 or go to http://www .
Owner’s Manuals These Owner’s Manuals have been prepar ed with the assistance of service and engineering specialists to ac- quaint you with specific Chrysler Group LLC vehicles. Included are starting, operating, emergency and mainte- nance procedures as well as specifications, capabilities and safety tips.
significantly from the norm due to variations in driving habits, service practices, and differ ences in road charac- teristics and climate. T raction Grades The T raction grades, fr om highest to lowest, are AA, A, B, and C.
material of the tire to degenerate and reduce tire life, and excessive temperatur e can lead to sudden tire failure. The grade C corresponds to a level of performance, which all passenger car tires must meet under the Federal Motor V ehicle Safety Standard No.
.
INDEX 10.
ABS (Anti-Lock Brake System) ............... .451 Adaptive Cruise Contr ol (ACC) (Cruise Control) . . .189 Adding Engine Coolant (Antifreeze) ........... .605 Additives, Fuel .......................... .514 Airbag .................................. 6 7 Airbag Deployment .
Automatic T ransaxle ...................... .417 Automatic T ransmission ................... .420 Adding Fluid ......................... .613 Fluid and Filter Changes ................. .613 Fluid Change ......................... .613 Fluid Level Check .
Oil (Engine) .......................... .583 Radiator (Coolant Pressur e) ............... .607 Carbon Monoxide W arning .................. 1 1 8 Cargo Area Cover ........................ .306 Cargo Area Features ...................... .304 Cargo Compartment .
Pressur e Cap ......................... .607 Radiator Cap ......................... .607 Selection of Coolant (Antifreeze) ............ .604 Corrosion Protection ...................... .615 Cruise Control (Speed Control) ............... .189 Cupholders .
Jump Starting ......................... .570 Overheating .......................... .545 Emission Control System Maintenance ......... .586 Engine ................................ .583 Air Cleaner .......................... .593 Block Heater .........
Engine Oil ........................... .592 Engine Oil Disposal .................... .592 Flashers Hazard W arning ....................... .545 T urn Signal .......................... .121 Flash-T o-Pass ........................... .172 Flooded Engine Starting .
Gasoline, Clean Air ....................... .512 Gasoline (Fuel) ........................... 5 1 1 Gasoline, Reformulated .................... .512 Gauges Coolant T emperature .................... .324 Fuel ................................ .324 Speedometer .
Hill Start Assist .......................... .456 Hitches T railer T owing ........................ .525 Holder , Coin ............................ .303 Holder , Cup ............................ .301 HomeLink® (Garage Door Opener) ........... .275 Hood Release .
Lane Change and T urn Signals ............... .171 Lane Change Assist ....................... .172 Lap/Shoulder Belts ......................... 5 6 Latches ............................... .121 Hood ............................... .164 Latch Plate ....
License ............................. .638 Lights On Reminder .................... .169 Malfunction Indicator (Check Engine) ........ .325 Parade Mode (Daytime Brightness) .......... .175 Passing ............................. .172 Rear Servicing .....
Memory Feature (Memory Seat) .............. .159 Memory Seat ........................... .159 Memory Seats and Radio ................... .159 Methanol .............................. .513 Mirrors ............................... .130 Electric Powered ..
Oil Filter , Selection ....................... .593 Onboard Diagnostic System ................. .585 Opener , Garage Door (HomeLink®) ........... .275 Operating Precautions ..................... .585 Operator Manual (Owner’s Manual) ............. 5 Outside Rearview Mirrors .
Rear ParkSense System .................... .231 Rear Seat, Folding ........................ .156 Rear W indow Defroster .................... .309 Rear W indow Features .................... .308 Rear W iper/W asher ....................... .308 Recorder , Event Data .
Safety Information, T ire .................... .474 Safety T ips .............................. 1 1 7 Schedule, Maintenance .................... .644 Seat Belt Maintenance ..................... .621 Seat Belt Reminder ......................... 6 5 Seat Belts .
Side V iew Mirror Adjustment ................ .132 Signals, T urn ........................... .121 Sky Slider Power Roof ..................... .289 SmartBeams ............................ .168 Snow Chains (T ire Chains) .................. .496 Snow T ires .
System, Remote Starting ..................... 2 9 T achometer ............................. .318 T elescoping Steering Column ................ .181 T emperature Control, Automatic (A TC) ......... .397 T emperature Gauge, Engine Coolant ........... .324 Theft Alarm (Security Alarm) .
T read W ear Indicators ................... .493 T ire Safety Information .................... .474 T ongue W eight/T railer W eight ............... .527 T o Open Hood .......................... .164 T owing ............................... .521 Disabled V ehicle .
Upholstery Care ......................... .619 V anity Mirrors .......................... .135 V ehicle Identification Number (VIN) ............. 7 V ehicle Loading ......................... .482 V ehicle Modifications/Alterations ............... 8 V ehicle Storage .
VEHICLES SOLD IN CANADA With respect to any V ehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
1283259cv1 14WK741-126-AA Grand Cherokee Chrysler 1" gutter 12/05/2012 15:56:03 Gr and Cher ok ee Chrysler Group LLC O WNER’S MANU AL 2014 Gr and Cherok ee 14WK741-126-AA Second Edition Printed in U.S.A. 2014 Gr and Cher ok ee Chrysler Group LLC O WNER’S MANU AL 2014 Gr and Cherok ee 14WK741-126-AA Second Edition Printed in U.
Ein wichtiger Punkt beim Kauf des Geräts Jeep Cherokee (2014) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Jeep Cherokee (2014) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Jeep Cherokee (2014) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Jeep Cherokee (2014) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Jeep Cherokee (2014) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Jeep Cherokee (2014) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Jeep Cherokee (2014) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Jeep Cherokee (2014). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Jeep Cherokee (2014) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
