Benutzeranleitung / Produktwartung CV-A50 des Produzenten JAI
Zur Seite of 27
Industrial Monochrome CCD Camera CV -A50 / CV -A60 Operation Manual Camera: CV -A50 Revision B CV -A60 Revision A Manual: Version 2.1 A50Manualjul14.doc JPT 14-07-03.
CV-A50 / CV-A60 DECLARA TION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EE C EMC (ELECTROMAGNETIC COMPAB ILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWING PROV ISIONS APPLYING TO IT. EN-50081-1 EN-50082-1 Table of Contents 1.
CV-A50 / CV-A60 1. Gener al The difference from the previous manual is that the CCD sen sor in CV-A50 is changed to new types. Now the used CCD sensors are: ICX-408AL-6, 409AL -6, 418ALL-6, 419ALL-6.
CV-A50 / CV-A60 4. Camer a Housing and Dimensions Fig. 1. Locations and dimensions. 1. 12 pin Hirose connector for frame grabber interfacing and power (12V DC). 2. BNC connector for video output. VS 1.0 Vpp 75 Ohm. 3. 6 pin Hirose connector for trigger input and RS-232C control interface.
CV-A50 / CV-A60 5. Pin Assignment 5.1. 12-pin Multi-connector (DC- IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Pin configuration is compatible with EIAJ standard Pin no. Signal Remarks 1 GND 2 +12 V DC input 3 GND 4 Video output Parallel with t he BNC connector.
CV-A50 / CV-A60 5.3. Input and Output Circuits In the following schematic diagrams the input and outpu t circuits for video and timing signa ls are shown. Jumper settings are shown as for fact ory default. For alternative connections refer to “10.1.
CV-A50 / CV-A60 6. F unctions and Operations Apart from the standard continuous operatio n, the CV-A50/60 features three external asynchronous trigger modes (edge pr e-select, pulse width controlled and start/stop) and a special frame-delay readout mode.
CV-A50 / CV-A60 6.2. Input-output of HD/VD Signals In the default setting the camera will accept external HD/VD signals on pin 6 and 7 of the 12 pin Hirose connector. If external HD/VD is applied, th e camera will synchronize to it. If no external sync signals are applied, the camera will oper ate with its internal x-tal controlled sync.
CV-A50 / CV-A60 Fig. 10. Horizontal timing details and pixel numbering for the CCD array. CCIR Fig. 11. Horizontal timing details and pixel numbering for the CCD array.
CV-A50 / CV-A60 Fig. 12. Vertical timing details for interlaced. CCIR Fig. 12A. Vertical timing details for non-interlaced. CCIR - 9 -.
CV-A50 / CV-A60 Fig. 13. Vertical timing details for interlaced. EIA Fig. 13A. Vertical timing details for non-interlaced. EIA - 10 -.
CV-A50 / CV-A60 6.4. External Trigger Modes This camera has 5 external asynchr onous trigger modes, which can be s et by RS-232C commands. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure.
CV-A50 / CV-A60 6.5. Edge Pre-select Mode The leading edge of the trigger pulse initiates the exposure. The exposure time (accumulation time) is governed by the pre-defined shutter sp eed set by RS-232C.
CV-A50 / CV-A60 6.6. Pulse Width Control Mode The leading edge of the trigger pulse initiates the exposure. The exposure time (accumulation time) is governed by duration of the trigger pulse.
CV-A50 / CV-A60 6.7. Frame-delay read out Mode This mode allows simultaneous c apture of multiple camera using a common external trigger pulse subsequent multiplexed (sequential) readou t using a single input frame grab ber, as the user has control over when the image is read ou t from the CCD sensor.
CV-A50 / CV-A60 6.8. Long Time Exposure Mode The exposure time is the interval between 2 ext. VD pulses sent to the VD input of the camera (Pin No. 7 of the 12-pin Hirose connector). The ex posure starts after input of the first ext. VD pulse, and ends after the next input of the ne xt ext.
CV-A50 / CV-A60 6.9. Start/Stop Mode The exposure time is controlled by the interval between the ext. trigger and the ext. VD signal. The exposure starts at the first HD pulse after t he falling edge of the ext. trigger, and stops 14.5 H after the falling edge of the VD pulse.
CV-A50 / CV-A60 Important notes on using this mode: - • As the start of exposure will be sync hronized with the internal H signal, the start of exposure may be shifted by max 1H. • To avoid this shift (jitter), synchro nize the camera with an external HD and m ake sure that the trigger pulse aligns to the HD signal as shown in Fig.
CV-A50 / CV-A60 7. Configuring the Camer a 7.1. RS-232C control. All configuration of the A50/60 camera is done vi a the RS -232C port. The camera can be set up from a PC running terminal emulator softwa re, or using JAI´s camera control software. Below is the description of the ASCII based short command p rotocol.
CV-A50 / CV-A60 7.2. CV-A50/60 RS-232C command list. Command Name Format Parameter Remarks A – General settings and useful commands EB Echo Back EB= [ Param.
CV-A50 / CV-A60 7.3. Camera Control Tool for CV-A50/60 From www.jai.com CV-A50/60 Camera Control Tool for Wind ows 98/NT/2000 can be downloaded. The control tool contents a camera control program and tools for m aking your own program. Below the different windows are sh own.
CV-A50 / CV-A60 7.4. Internal Switch and Jumper Settings. 7.4.1 HD/VD input-output selection In the default setting the camera will accept external HD/VD signals on pins 6 and 7 of the 12 pin Hirose connector. The compos ite video signal from the camera will be synchr onized to an external HD/VD source connected to the camera.
CV-A50 / CV-A60 8. Specifications Specifications CV-A50C CV-A60C CV-A50E CV-A60E Scanning system CCIR, 25 frames/sec. 625 lines, 2:1 Interlaced EIA. 30 frames/sec. 525 lines, 2:1 Interlaced Frame rate (Full frame) 50 Hz 59.94 Hz Line frequency 15.625 kHz 15.
CV-A50 / CV-A60 9. Spectr al Sensiti v ity 400 500 600 700 800 900 Wave Length (nm) 1.0 0.8 0.6 0.4 0.2 0.0 Relative Response 1000 Fig. 30. Spectral sensitivity.
CV-A50 / CV-A60 10.2. WEN out on pin 6 on 6 pin connector Instead of EEN output on pin #6 on the 6 pin Hirose connector, WEN c an be output by jumper settings.
CV-A50 / CV-A60 10.4. Precautions Personnel not trained in dealing with similar elec tronic devices should not service this camera. The camera contains components sensitive to el ectrostatic discharge. The handling of these devices should follow the requirements of electrostatic se nsitive components.
CV-A50 / CV-A60 11. Users Record Camera type: CV-A50/60 CCIR/EIA Revision: CV-A60 Revision A. CV-A50 revision B Serial No. …………….. For camera revision hi story, please contact your local JAI d istributor.
Ein wichtiger Punkt beim Kauf des Geräts JAI CV-A50 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JAI CV-A50 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JAI CV-A50 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JAI CV-A50 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JAI CV-A50 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JAI CV-A50 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JAI CV-A50 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JAI CV-A50. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JAI CV-A50 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
