Benutzeranleitung / Produktwartung Tracer EXIR des Produzenten Invacare
Zur Seite of 44
DEALER: THIS MANUAL MUST BE GIVEN TO THE USER OF THE WHEELCHAIR. USER: BEFORE USING THIS WHEELCHAIR, READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE. Owner's Operator And Maintenance Manual Tracer EXI R For more information regarding Invacare products, parts, and services, please visit: www.
Tracer® EXI 2 Part No. 1110547 WARNING WARN IN G WARNING DO NOT OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND.
Part No. 1110547 3 Tracer® EXI CONTENTS CONTENTS TABLE OF CONTENTS SPECIAL NOTES ................................................................................ 5 LABEL LOCATIONS ......................................................................
Tracer® EXI 4 Part No. 1110547 CONTENTS CONTENTS SECTION 8 - ANTI-TIPPERS/WH EEL LOCKS .................................... 3 5 INSTALLING/ADJUSTING THE ANTI-TIPPERS ........................................................................... 3 5 WHEEL LOCK ADJUSTMENT .
Part No. 1110547 5 Tracer® EXI SPECIAL NOTES WARNING/CAUTION notices as used in this manual apply to hazards or unsafe practices which could result in personal injury or property damage. NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Tracer® EXI 6 Part No. 1110547 IMPOR T ANT NOTICE The wheel locks on this wheelchair have been pre-set at the factory to comply with the V eterans Adm inistration functional S t andard 8320.01 of the Federal Register , paragraph 3.2.4.5.3. If these wheel locks do not meet your needs, follow instructions below.
Part No. 1110547 7 Tracer® EXI TRACER EXI Overall Width Permanent Arm: 23-1/4, 25-1/4, 27-1/4-inches Removable Arm: 24-1/2, 26-1/2, 28-1/2-inches Overall Depth: 31-7/8-inches (without Front Riggings).
Tracer® EXI 8 Part No. 1110547 SECTION 1 GENERAL GUIDELINES GENERAL GUIDELINES STABILITY - ALL MODELS WARNING The size/position of the front casters, size/position of the rear wheels, use of anti-tipper model, as well as the user condition directly relate to the stability of the wheelchair.
Part No. 1110547 9 Tracer® EXI OPERATING INFORMATION WARNING Unless otherwise noted, all service and adjustments should be performed while the wheelchair is unoccupied. After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result.
Tracer® EXI 10 Part No. 1110547 TIRE PRESSURE WARNING DO NOT use your wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT overinflate the tires. Failure to follow these instructions may cause the tire to explode and cause bodily harm. The recommended tire pressure is listed on the side wall of the tire.
Part No. 1110547 11 Tracer® EXI SAFETY/HANDLING OF WHEELCHAIRS Safety and Handling of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and tech- niques involved in the safe operation and maintenance of the wheelchair.
Tracer® EXI 12 Part No. 1110547 WARNING DO NOT attempt to lift the wheelchair by any removable (detachable) parts. Lifting by means of any removable (detachable) parts of a wheelchair may result in injury to the user and/or assistant or damage to the wheelchair.
Part No. 1110547 13 Tracer® EXI Reaching, Leaning and Bending - Forward. WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees. Position the front casters so that they are extended as far forward as possible and engage wheel locks.
Tracer® EXI 14 Part No. 1110547 TIPPING - CURBS: METHOD 1 - WHEELCHAIR WITH STEP TUBES: Place foot on the step tube and begin to tilt the wheelchair toward you. Apply a continu- ous downward motion until the balance point is achieved and the front casters clear the curb.
Part No. 1110547 15 Tracer® EXI STAIRWAYS WARNING ALWAYS wear your seat/chest positioning strap. Inasmuch as the SEAT/ CHEST POSITIONING STRAP is an option on this wheelchair (You may order with or w.
Tracer® EXI 16 Part No. 1110547 UNFOLDING AND FOLDING THE WHEELCHAIR WARNING Keep hands and fingers clear of moving parts to avoid injury. DO NOT sit or transfer into the wheelchair unless it is fully open and the seat frame rails are fully seated into the side frame H-blocks.
Part No. 1110547 17 Tracer® EXI Folding. 1. Swing footrest/legrest and calfpads (if equipped) in locked position to the front of the wheelchair. 2. Pivot footplates upward to vertical position. 3. With both hands, grasp the middle of the seat upholstery at the front and back edge and lift up.
Tracer® EXI 18 Part No. 1110547 SECTION 2 SAFETY INSPECTION SAFETY INSPECTION CHECKLIST NOTE: Every six (6) months or as necessary, take your wheelchair to a qualified technician for a thorough inspection and servicing. Regular cleaning will reveal loose or worn parts and enhance the smooth opera- tion of your wheelchair.
Part No. 1110547 19 Tracer® EXI TROUBLESHOOTING MAINTENANCE MAINTENANCE SAFETY PRECAUTIONS MAINTENANCE SAFETY PRECAUTIONS MAINTENANCE SAFETY PRECAUTIONS MAINTENANCE SAFETY PRECAUTIONS MAINTENANCE SAF.
Tracer® EXI 20 Part No. 1110547 SECTION 2 SAFETY INSPECTION SAFETY INSPECTION SAFETY INSPECTION 6. Periodically check caster and rear wheel bearings to make sure they are clean and free from moisture. Use a Teflon® lubricant if necessary. WARNING When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water.
Part No. 1110547 21 Tracer® EXI FRONT RIGGINGS FRONT RIGGINGS SECTION 3 Section 3 - Front Riggings includes the following: Installing/Removing the Front Riggings Footplate Height Adjustment Adjusting.
Tracer® EXI 22 Part No. 1110547 SECTION 3 FRONT RIGGINGS FRONT RIGGINGS FOOTPLATE HEIGHT ADJUSTMENT SPRING BUTTON HEIGHT ADJUSTMENT (FIGURE 2) NOTE: This procedure applies to the swingaway front riggings and swingaway elevating legrest. 1 . Remove the front rigging assembly.
Part No. 1110547 23 Tracer® EXI SECTION 3 FRONT RIGGINGS FRONT RIGGINGS FIGURE 3 - FOOTPLATE HEIGHT ADJUSTMENT - BOLT-IN-PLACE HEIGHT ADJUSTMENT 6 . From the outside of the swingaway front rigging, insert the riv nut through both the front rigging support and the footplate assembly.
Tracer® EXI 24 Part No. 1110547 SECTION 3 FRONT RIGGINGS FRONT RIGGINGS HEEL LOOP REPLACEMENT (FIGURE 6) 1 . Pull the cam lock lever UP to UNLOCKED position.
Part No. 1110547 25 Tracer® EXI SECTION 3 FRONT RIGGINGS FRONT RIGGINGS FIGURE 6 - HEEL LOOP REPLACEMENT Spacer Locknut Cam Lock Lever Heel Loop Slide Tube Mounting Screw Footplate Assembly Footplate OUTSIDE OF SWINGAWAY FRONT RIGGING INSIDE OF SWINGAWAY FRONT RIGGING NOTE: Swingaway footrests shown.
Tracer® EXI 26 Part No. 1110547 Armrest Release Button Armrest Release Handle Armrest REAR Arm Socket FRONT Arm Socket FIGURE 1 - REMOVING/INSTALLING STANDARD ARMREST SECTION 4 ARMS ARMS Section 4 - .
Part No. 1110547 27 Tracer® EXI Phillips Screws Section 5 - Seat and Back includes the following: Replacing Back Upholstery Replacing Seat Upholstery Adjusting Seat Width WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur.
Tracer® EXI 28 Part No. 1110547 SEAT AND BACK SECTION 5 SEAT AND BACK ADJUSTING THE SEAT WIDTH EXI WITH SWINGAWAY FRONT RIGGINGS (FIGURE 3) NOTE: When adjusting the seat width of the wheelchair, the back and seat upholstery MUST be changed. If applicable, the headrest pillow and headrest upholstery MUS T be changed as well.
Part No. 1110547 29 Tracer® EXI FIGURE 3 - ADJUSTING THE SEAT WIDTH - EXI WITH SWINGAWAY FRONT RIGGINGS Crossbrace Saddle Washer Wheelchair Frame Crossbrace Saddle (STEPS 3,8) Crossbrace (STEPS 4,5) .
Tracer® EXI 30 Part No. 1110547 EXI WITH FIXED FRAME (FIGURE 4) Removing Lower Mounting Hardware (DETAIL "A"). 1. Remove the existing back and seat upholstery from the wheelchair. Refer to RE- PLACING THE BACK UPHOLSTERY and REPLACING THE SEAT UPHOLSTERY in this section of the manual.
Part No. 1110547 31 Tracer® EXI REAR WHEELS SECTION 6 Section 6 - Rear Wheels includes the following: Removing/Installing the Rear Wheels Replacing Rear Wheel Handrim Replacing/Repairing Rear Wheel T.
Tracer® EXI 32 Part No. 1110547 REPLACING REAR WHEEL HANDRIM (FIGURE 2) 1. Remove the rear wheel from the wheelchair. Refer to REMOVING/ INSTALLING THE REAR WHEELS in this section of the manual. 2. Remove the mounting screws and washers (not shown) that secure the handrim to the rear wheel.
Part No. 1110547 33 Tracer® EXI FRONT CASTERS SECTION 7 FRONT CASTERS Section 7 - Front Casters includes the following: Installing/Replacing Fork Assemblies Adjusting Forks Replacing Front Casters Re.
Tracer® EXI 34 Part No. 1110547 REPLACING FRONT CASTERS (FIGURE 2) WARNING If converting from six-inch casters to eight-inch casters or vice versa, the fork assemblies MUST be replaced. Refer to INSTALLING/REPLACING FORK ASSEMBLIES in this section of the manual.
Part No. 1110547 35 Tracer® EXI ANTI-TIPPERS/WHEEL LOCKS SECTION 8 ANTI-TIPPERS/WHEEL LOCKS Section 8 - Anti-tippers/Wheel Locks includes the following: Installing/Adjusting the Anti-Tippers Using/Ad.
Tracer® EXI 36 Part No. 1110547 SECTION 8 ANTI-TIPPERS/WHEEL LOCKS ANTI-TIPPERS/WHEEL LOCKS FIGURE 2 - INSTALLING THE ANTI-TIPPERS Anti-Tipper Release Buttons Rear Frame Tubing Anti-Tipper Wheels 1-1/2 to 2-inch Clearance FIGURE 3 - ADJUSTING THE ANTI-TIPPERS Release Buttons 1.
Part No. 1110547 37 Tracer® EXI SECTION 8 ANTI-TIPPERS/WHEEL LOCKS ANTI-TIPPERS/WHEEL LOCKS USING/ADJUSTING THE DISK WH EEL LOCKS USING THE PATIENT OPERATED DISK WHEEL LOCKS (FIGURE 3) WARNING DO NOT attempt to stop a moving wheelchair with the wheel locks.
Tracer® EXI 38 Part No. 1110547 ANTI-TIPPERS/WHEEL LOCKS SECTION 8 ANTI-TIPPERS/WHEEL LOCKS NOTE: Any wheel lock adjustment should embed the wheel lock shoe at least 1/8-inch (3/16-inch if pneumatic tire) into the tire when engaged.
Part No. 1110547 39 Tracer® EXI Section 9 - Seat-to-Floor Height includes the following: Changing Seat-To-Floor Height CHANGING SEAT-TO-FLOOR HEIGHT (FIGURE 1) WARNING The size/position of the front casters, size/position of the rear wheels, use of anti-tipper model, as well as the user condition directly relate to the stability of the wheelchair.
Tracer® EXI 40 Part No. 1110547 6 OR 8-INCH FORK MOUNTING POSITIONS TOP MIDDLE BOTTOM REAR WHEEL MOUNTING POSITIONS - ADULT/HEMI FRAME STYLE TOP BOTTOM FIGURE 1 - CHANGING SEAT-TO-FLOOR HEIGHT *6-INC.
Part No. 1110547 41 Tracer® EXI Section 10 - Options includes the following: Installing the Seat Positioning Strap WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attach- ing hardware is tightened securely - otherwise injury or damage may occur.
Tracer® EXI 42 Part No. 1110547 NOTES NOTES NOTES NOTES NOTES NOTES NOTES.
Part No. 1110547 43 Tracer® EXI LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products.
Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare and Tracer are registered Elyria, Ohio USA Mississauga Ontario trademarks of Invacare Corporation. 44036-2125 L4Z 4G4 Canada Yes, you can. is a trademark of Invacare 800-333-6900 800-668-5324 Corporation.
Ein wichtiger Punkt beim Kauf des Geräts Invacare Tracer EXIR (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Invacare Tracer EXIR noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Invacare Tracer EXIR - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Invacare Tracer EXIR reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Invacare Tracer EXIR erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Invacare Tracer EXIR besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Invacare Tracer EXIR verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Invacare Tracer EXIR. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Invacare Tracer EXIR gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
