Benutzeranleitung / Produktwartung SQ599 des Produzenten Intel
Zur Seite of 55
SQ599 1 Table of Contents Section 1 Introduction........................................................ 3 1-1 How To Use This Manual............................... 3 1-2 Overview..................................................... 3 1-3 Product Specification.
SQ599 2 Section 5 VGA Installation.................................................. 34 5-1 SiS 6205 VGA Feature.................................. 34 5-2 DOS Utility.................................................. 34 5-2-1 Install Program: INSTDRV.EXE.
SQ599 3 Section 1 Introduction 1-1 How To Use This Manual This manual provides information necessary for Original Equipment Manufacturers (OEMs) to build a PC-AT compatible system using the Pentium PCI motherboard. For the end-users, this manual is a good reference to understand and properly use the motherboard.
SQ599 4 1-3 Product Specification CPU • intel Pentium 75-200MHz processors, Cyrix 6x86 • intel Pentium P55C processor System Chipset • High performance SiS5511/5512/5513 chipset VGA Chipset • .
SQ599 5 1-4 Board Layout.
SQ599 6 Section 2 Configuration Guide 2-1 Memory Configuration The SQ599 motherboard supports standard Fast Page DRAM or EDO DRAM improve the DRAM read performance. The motherboard provides four 72-pin SIMM sockets.It can be 1MBx32/36(4MB), 2MBx32/36(8MB), 4MBx32/36(16MB) and 8MBx32/36(32MB).
SQ599 7 2-2-2 OTHER JUMPER SETTING JP1 Open Color (DEFAULT) Close Mono JP19 1-2 Normal (DEFAULT) 2-3 Clear CMOS JP24 Open EPOM BIOS Close FLASH BIOS JP20 External RTC Connector J1 Key Board Connector .
SQ599 8 Section 3 System Setup This section provides the information for the system setup procedure and also briefs the setup procedures for system BIOS .
SQ599 9 7. The system should have correct configuration information by now and should have no problem booting up the operating system from floppy or hard disk. If not, check the peripheral types, memory size and connections and go through the SETUP utility again.
SQ599 10 SECTION 4 BIOS SETUP 4-1 Entering Setup Power on the computer and press <Del> immediately will allow you to enter Setup. The other way to enter Setup is to power on the computer, when t.
SQ599 11 F5 key Restore the previous CMOS value from CMOS, only for Option Page Setup Menu F6 key Load the default CMOS value from BIOS default table, only for Option Page Setup Menu F7 key Load the S.
SQ599 12 Standard CMOS setup This setup page includes all the items in a standard compatible BIOS. See Page 13 to Page 17 for details. BIOS Features setup This setup page includes all the items of Award special enhanced features. See Page 17 to Page 21 for details.
SQ599 13 4-4 Standard CMOS Setup The items in Standard CMOS Setup Menu divide into 10 categories. Each category includes no, one or more than one setup item. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item.
SQ599 14 ROM PCI/ISA BIOS (2A5IA000) STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm:dd:yy) : Fri, Apr 7 1995 Time(hh:mm:ss) : 00:00:00 HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDE SECTOR MODE Prima.
SQ599 15 Primary Master/Primary Slave/Secondary Master/Secondary Slave The categories identify the types of 2 channels that have been installed in the computer. There are 45 predefined types and 4 user definable types are for Enhanced IDE BIOS. Type 1 to Type 45 are predefined.
SQ599 16 Video The category selects the type of adapter used for the primary system monitor that must match your video display card and monitor. Although secondary monitors supported, you do not have to select the type in Setup. You have two ways to boot up the system: 1.
SQ599 17 512K for systems with 512K memory installed on the motherboard, or 640K for systems with 640K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST . This is the amount of memory located above 1MB in the CPU's memory address map.
SQ599 18 and the following error message will appear, in the mean time, you can run an anti-virus program to locate the problem. ! WARNING ! Disk boot sector is to be modified Type "Y" to accept write or "N" to abort write Award Software, Inc.
SQ599 19 A,C System will first search for floppy disk drive then hard disk drive. Note: This function is only available for IDE type For SCSI type is always boot from A. Boot Up Floppy Seek During POST , BIOS will determine if the floppy disk drive installed is 40 or 80 tracks.
SQ599 20 Disabled Ignore memory parity check even the DRAM has no parity bit. The system will not display “RAM parity error”..
SQ599 21 Typematic Rate Setting This determines the typematic rate . Enabled Enable typematic rate and typematic delay programming Disabled Disable typematic rate and typematic delay programming. The system BIOS will use default value of these 2 items and the default is controlled by keyboard.
SQ599 22 Note: To disable security, select PASSWORD SETTING at Main Menu and then you will be asked to enter password. Do not type anything and just press <Enter>, it will disable security. Once the securities disable, the system will boot and you can enter Setup freely.
SQ599 23 4-6 VGA Memory Setup The VGA memory setup will appear on your screen like this ROM PCI/ISA BIOS (2A51DB3A) CHIPSET FEATURES SETUP AWARD SOFTWARE, INC.
SQ599 24 4-7 Power Management Setup The Power management setup will appear on your screen like this: ROM PCI/ISA BIOS (2A4IBG33) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. Power Management : Max Saving IRQ4 (COM 1) : Enable PM Control by APM : Yes IRQ5 (LPT 2) : Enable Video Off Option : Susp, Stby -> Off IRQ6 (Floppy Disk) : Enable .
SQ599 25 Item Options Descriptions B. PM Control by APM 1. No System BIOS will ignore APM when power managing the system 2. Yes System BIOS will wait for APM’s prompt before it enter any PM mode e.
SQ599 26 2. Enable The External Suspend Switch is enabled F. HDD Off After 1. Disable HDD’s motor will not off (#) Remark 2 2. 1 Min 2 Min 3 Min 4 Min 5 Min 6 Min 7 Min 8 Min 9 Min 10 Min 11 Min 12 Min 13 Min 14 Min 15 Min Defines the continuous HDD idle time before the HDD entering power saving mode (motor off) 3.
SQ599 27 30 Min 40 Min 1 Hr 2 Hr 3 Hr Note: Normally,STANDBY mode puts the system into low speed or 8 MHz, screen may be off depend on (E) H. Standby Mode (*) Remark 1 1.
SQ599 28 (*) Remark 1 mode 2. 10 Sec 20 Sec 30 Sec 40 Sec 1 Min 3 Min 5 Min 10 Min 15 Min 20 Min 30 Min 40 Min 1 Hr 2 Hr 3 Hr Defines the continuous idle time before the system entering SUSPEND mode.
SQ599 29 IRQ15 (Reserved) * Remark 1: All items mark with (*) in this menu, will be loaded with predefined values as long as the item ‘Power Management ’ is not configured to ‘User Defined’ Th.
SQ599 30 The following pages tell you the options of each item & describe the meanings of each options. Item Options Descriptions A. Slot 1 Using INT# Slot 2 Using INT# Slot 3 Using INT# AUTO A B .
SQ599 31 SLOT2 PCI- SLOT3 ISA determine the location of the PCI IDE device (See below item) PCI-SLOT1 PCI-SLOT2 PCI-SLOT3 − assign IRQ 14 for primary IDE INT# IRQ 15 for secondary IDE INT# for the s.
SQ599 32 HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master : To disable password, just press <Enter> when you prompt to enter password. A message will confirm the password being disabled. Once the passwords disable, the system will boot and you can enter Setup freely.
SQ599 33 <II> Standard CMOS Setup CYLS HEADS PRECOMP LANDZONE SECTOR MODE Drive C : User (516MB) 1120 16 65535 1119 59 NORMAL Drive D : None(203MB) 684 16 65535 685 38 ---------- When HDD type is in ‘user’ type, the “MODE ” option will be opened for user to select their own HDD mode.
SQ599 34 CMOS CHECKSUM ERROR Checksum of CMOS is incorrect. This can indicate that CMOS has become corrupt. This error may cause a weak battery. Check the battery and replace if necessary. DISPLAY SWITCH IS SET INCORRECTLY Display switch on the motherboard can be set to either monochrome or color.
SQ599 35 Section 5 VGA Installation 5-1 SiS 6205 VGA Feature • Supports 64-bit PCI local bus standard Revision 2.1 • Supports full motion picture up to 1024x768x256 mode • Supports graphics/vide.
SQ599 36 (1) For some software packages (e.g. ADI packages, PCAD), their dr iver files can be put to any directory you prefer. (2) For some software packages (e.g. WordPerfect, GEM/Ventura, VersaCAD/386, Lotus 1-2-3), the driver files must be put to where main program resides.
SQ599 37 For example : Set 720x400 color text mode with 84Hz frame rate. >SVGAUTL /F0:84 <Enter> /F1: Set frame rate to be n1 Hz. For example : Set 640x480 graphic mode with 60Hz frame rate >SVGAUTL /F1:60 <Enter> /F2: Set frame rate to be n2 Hz.
SQ599 38 The SiS6205 VGA Video Mode is shown as below. This table is the refercnce for you to use the SVAGUTL.EXE utility. Standard Mode MODE DISPLAY SIZE COLORS SHADES FRAME RATE. H- SYNC. VIDEO FREQ. 0 320x200 16 70 31.5 K 25.1 M 0* 320x350 16 70 31.
SQ599 39 Enhanced Mode MODE DISPLAY SIZE COLORS SHADES FRAME RATE. H- SYNC. VIDEO FREQ. 22 1056x352 16 70 30.5 K 40.0 M 23 1056x350 16 70 30.5 K 40.0 M 24 1056x364 16 70 30.5 K 40.0 M 25 640x480 16 60 31.5 K 25.1 M 26 720x480 16 60 31.5 K 25.1 M 29 800x600 16 56 35.
SQ599 40 41 320x200 64K 70 31.5 K 25.1 M 42 320x200 16.8M 70 31.5 K 25.1 M 43 640x480 32K 60 31.5 K 25.1 M 43* 640x480 32K 72 37.9 K 31.5 M 43+ 640x480 32K 75 37.5 K 31.5 M 44 640x480 64K 60 31.5 K 25.1 M 44* 640x480 64K 72 37.9 K 31.5 M 44+ 640x480 64K 75 37.
SQ599 41 5-3 Software Drivers To make use of the advance features of SiS 6205, extended graphic and text modes are supported by software application drivers developed by SiS. The following applications are currently supported: • 3D Studio Ver. 3.0 • AutoCAD/386 Release 11, 12 • Auto Shade/386 Ver.
SQ599 42 Windows Setup 1. In "SiS VGA Driver" program group, choose "Setup" icon to enter setup screen. choose which options you would like to use. 2. After completing your selections, choose "OK". 3. Choose "Restart Winodws" to re-boot Windows using new settings.
SQ599 43 Driver Files The OS/2 3.0 driver files resides on the "SiS 6205 Driver Diskette Sub-directory OS2WARP (i.e. OS2WARP)". The enclosed SiS 6205 OS/2 3.0 driver contains the following files: SISINST.CMD SiS driver install program SVGA.EXE SiS PMI Generator S768256.
SQ599 44 1024x768 256-colors 1280x1024 256-colors (only suits for 2MB.) 640x480 64K-colors 800x600 64K-colors 1024x768 64K-colors (only suits for 2MB.) 12. If you want to change resolution, run system icon of System Setup Group in PM, highlight the resolution you want to use and quit, shut down the system and restart again.
SQ599 45 7. Go through the whole instructions, and the system would start with the desired display setting. AutoCAD R12 Setup 1. The following procedures assume that (1) You have complete "unpack & copy" procedure. (2) Your SiS ADI 4.2 drivers are located in C:ADI42.
SQ599 46 6. While prompting "Select rendering display driver:", choose "P386 AutoDesk Device Interface rendering driver.". 3D Studio Version 3.0 Setup 1. The following procedures assume that (1) You have complete "unpack & copy" procedure.
SQ599 47 (3) In "Render-Display" item, (a) Press <Enter> The selection menu will appear. (b) In selection menu, move cursor to "RCPADI" or "RDPADI". Press <Enter> to select. (4) Complete the other selections and exit configuration.
SQ599 48 132x28 132x44 3. Use "INSTDRV.EXE" to unpack and copy drivers to where they should resides, WordPerfect Setup 1. Run WordPerfect. 2. From the Main menu, choose File menu. 3. From the File menu, choose Setup menu. 4. From the Setup menu, choose Display menu.
SQ599 49 (2) create new VP.BAT file. Ventura Setup --- Create New VP.BAT To create new VP.BAT, please follow the following procedures: 1. In "Install and Setup GEM 3.0 / Ventura 2.0 Drivers" menu, select "B. Setup Ventura Batch File VP.
SQ599 50 2. From the "Setup PCAD Config File" screen, keyin the drive letter of the hard disk where PCAD software resides. 3. From the "Setup PCAD Config File" screen, keyin the directory where the PCAD drivers reside.
SQ599 51 For example: C:VCAD386>VSIS <Enter> 3. Run ENVIRO program. For example: C:VCAD386>ENVIRO <Enter> 4. From "ENVIRONMENT MENU" screen, press 'S' key to select screen configuration. 5. In prompt mode, select "SiS 6205" display driver.
SQ599 52 6. In the same "Configure Schematic Tools" screen, choose "Configured Display Driver" item and keyin one of the SiS OrCAD drivers' name which you would like to use. 7. If you want to configure anything else, do as you like.
SQ599 53 5-3-9 Lotus 2.x Driver Files 1. The enclosed SiS 6205 Lotus 1-2-3 drivers (packed files) are (1) LOTUS.1 (2) LOTUS.2 (3) LOTUS.3 (4) LOTUS.4 2. Being unpacked, the SiS 6205 Lotus 1-2-3 drivers contain the following files: (1) TXT13225.DRV: 132x25 Text (2) TXT13228.
SQ599 54 (3) Press RETURN key again. (4) From "Exit" menu, choose "Yes" option to terminate the INSTALL program. 6. Restart your Lotus 1-2-3 program. 5-3-10 Windows NT 3.5 Driver Files 1. The enclosed SiS 6205 Windows NT 3.5 drivers are: SISTAG SISV.
SQ599 55 1. Install and start your Windows 95 system. 2. Choose the “START ” from the screen and select “SETTINGS”, then choose “ CONTROL PANEL”. 3. In “CONTROL PANEL” screen, choose the “ DISPLAY” icon, you can see the “DISPLAY PROPERTIES” screen.
Ein wichtiger Punkt beim Kauf des Geräts Intel SQ599 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Intel SQ599 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Intel SQ599 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Intel SQ599 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Intel SQ599 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Intel SQ599 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Intel SQ599 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Intel SQ599. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Intel SQ599 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
