Benutzeranleitung / Produktwartung DTR-4.5 des Produzenten Integra
Zur Seite of 84
DTR-4.5 Instr uction Manual AV Receiv er DTR-4.5_En.book Page 1 Tuesday, August 10, 2004 9:39 AM.
2 Important Safety Instructions 1. Read these instructions. 2. K eep these instructions. 3. Heed all w arnings. 4. F ollow all instructions. 5. Do not use this apparatus near w ater . 6. Clean only with dry cloth. 7. Do not block an y ventilation openings.
3 Precautions F or U .S. Models Note to CA TV system installer: This reminder is provided to call the CA TV system installer’ s attention to Section 820-40 of the NEC which provides guidelines for p.
4 Precautions —Continued F or British models Replacement and mounting of an A C plug on the po wer supply cord of this unit should be performed only by qualified service personnel.
5 Features Amplifier • 85 watts per channel into 8 ohms, 2 channels dri ven from 20 Hz to 20 kHz, less than 0.08% total harmonic distortion (FTC rating) • 5-channel amplifier • Optimum Gain V .
6 Ta b le of Contents Basic Introduction Important Safety Instructions .......................................................................................... 2 Precautions ...........................................................................
7 Ta b le of Contents —Continued Adv anced Controlling Other Components Entering a Remote Control Codes................................. 69 Learning Commands from Another Remote Controller ............................................................
8 Fr ont & Rear P anels For detailed information, see the pages in parentheses. A Standby/On b utton (35) This button is used to set the A V receiv er to On or Standby . B Standby indicator (35) This indicator lights up when the A V receiver is in Standby mode, and it flashes while a signal is being receiv ed from the remote controller .
9 Front & Rear P anels —Continued S Return button This button is used to return to the pre viously dis- played onscreen setup menu. T Master V olume control (44) This control is used to adjust t.
10 Front & Rear P anels —Continued For detailed information, see the pages in parentheses. A COMPONENT VIDEO IN 1, 2, 3 (27, 29, 31) These component video inputs can be used to con- nect A V components with component video outputs, such as D VD players.
11 Front & Rear P anels —Continued J OPTICAL DIGIT AL (26, 27, 29, 31, 32, 33) The optical digital audio inputs can be used to con- nect CD and D VD players, and other components with an optical digital audio output. The optical output can be used to connect a CD recorder or other digital recorder with an optical digital input.
12 Remote Contr oller In addition to controlling the A V receiver, the remote controller has sev eral operating modes for controlling your other A V components, including Integra compo- nents connected via . Modes are selected by using the remote controller’ s Remote Mode b uttons.
13 Remote Controller —Continued A Standby b utton (35) This button is used to set the A V receiv er to Standby . B On button (35) This button is used to turn on the A V receiv er. C Input Selector buttons (44) These buttons are used to select the input source.
14 Remote Controller —Continued D VD mode is used to control an Integra D VD player connected to the A V receiver via . To set the remote contr oller to D VD mode, press the [D VD] Remote Mode button. A Standby b utton This button is used to set the D VD player to Standby .
15 Remote Controller —Continued P Video Off button This button is used to turn of f the internal video cir- cuitry , eliminating any possibility of interference. Q Clear button This button is used to cancel functions and to clear entered numbers. R Menu b utton This button is used to display a D VD’ s menu.
16 Remote Controller —Continued MD/CDR mode is used to control an Integra MiniDisc recorder or CD recorder connected to the A V receiver via . To select MD/CDR mode, press the [MD/CDR] Remote Mode button. By default, this b utton is set to control a MiniDisc recorder .
17 Remote Controller —Continued N Stop [ ] button This button is used to stop playback. O Random button This button is used with the random playback func- tion. P Memory button This button is used with the memory playback func- tion, which allows you to create a custom playlist of tracks.
18 Remote Controller —Continued Notes: • The batteries should last for about six months, although this will vary with usage. • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries.
19 About Home Theater Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of movement in your o wn home—just lik e being in a movie theater or concert hall. W ith D VDs you can enjoy DTS and Dolby Digital.
20 Connecting the A V receiver • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections.
21 Connecting the A V receiver —Continued Speaker Configuration F or the best surround-sound e xperience, you should con- nect sev en speakers and a po wered subwoofer . The following table indicates the channels you should use depending on the number of speakers that you ha ve.
22 Connecting the A V receiver —Continued Speaker Connection Precautions Read the following before connecting your speak ers: • Only connect speakers with an impedance of 6 ohms or higher .
23 Connecting the A V receiver —Continued This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and ho w to connect commercially av ailable outdoor FM and AM antennas. The A V receiver won’ t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner .
24 Connecting the A V receiver —Continued Connecting an Outdoor FM Antenna If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft.
25 Connecting the A V receiver —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiv er, you can select both the audio and video simultaneously simply by selecting the appropriate input source on the A V receiver.
26 Connecting the A V receiver —Continued Monitor Out ■ Using Composite Video Use a composite video cable to connect the A V receiver’ s V MONITOR OUT jack to a composite video input on your TV , as shown. ■ Using S-Video Use an S-V ideo cable to connect the A V receiv er’ s S MONITOR OUT jack to an S-V ideo input on your TV , as shown.
27 Connecting the A V receiver —Continued Video Connections Y ou only need to use one of the following connection methods. ■ Using Composite Video Use a composite video cable to connect the A V receiver’ s V D VD IN jack to the composite video output on your D VD player , as shown.
28 Connecting the A V receiver —Continued ■ Using a Multichannel Connection If your D VD player supports multichannel audio formats such as D VD-Audio, and it has a 5.
29 Connecting the A V receiver —Continued Video Connections If you connect to a component video input, you must assign it (see page 38). Use a component video cable to connect the A V receiv er’ s COMPONENT VIDEO IN2 or 3 jacks to a component video output on your D-VHS VCR, as shown.
30 Connecting the A V receiver —Continued This section explains ho w to connect a VCR for recording from a TV or another VCR. Video Connections • Use an S-V ideo cable to connect the A V receiv er’ s S VIDEO 1 OUT jack to an S-V ideo input on the recording VCR.
31 Connecting the A V receiver —Continued Video Connections Y ou only need to use one of the following connection methods. ■ Using Composite Video Use a composite video cable to connect the A V receiver’ s V VIDEO 3 IN jack to a composite video output on your video source, as shown.
32 Connecting the A V receiver —Continued ■ Using Analog Connections If your video source doesn’t ha ve a digital audio output, or you want to record from it, you’ll need to mak e the following analog audio connection.
33 Connecting the A V receiver —Continued Y ou can connect a DA T , CD, or MD recorder instead of a cassette recorder . ■ Analog Connections Use an analog audio cable to connect the A V receiver.
34 Connecting the A V receiver —Continued ■ T urntable with a Built-in Phono Preamp Use an analog audio cable to connect an unused audio input on the A V receiver to the audio outputs on your turntable, as shown.
35 Connecting the A V receiver —Continued The A V receiver has AC outlets on its rear panel that can be used to connect the power cords of A V other compo- nents that you intend to use with the A V receiver. These components can then be left turned on so that they turn on and off as and when the A V receiv er is turned on and set to Standby .
36 Fir st Time Setup The A V receiver is configured using onscreen setup menus, which are displayed on the TV that’ s connected to either of the MONITOR OUT jacks. Because the y appear on your TV , they’ re large and clear , making setup a breeze.
37 First Time Setup —Continued Digital Input If you connect a component to a digital input jack, you must assign that jack to an input selector . F or example, if you connect your CD player to the OPTICAL IN2 jack, you should assign that jack to the CD input selector .
38 First Time Setup —Continued Component Video Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector . F or example, if you connect your D VD player to COMPONENT IN 3, you should assign it to the D VD input selector .
39 First Time Setup —Continued Speaker Configuration Here you can specify which speakers are connected and their individual sizes. For speakers with a cone diameter ov er 6-1/2 inches (16 cm), specify lar ge, and for those with a diameter below this, specify small.
40 First Time Setup —Continued Crosso ver Notes: • If the crossov er frequency is set to a lo w value, and the program material doesn’t contain an y sounds below that frequency , the subwoofer will not output much sound.
41 First Time Setup —Continued Speaker Distance Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arriv es at the listener’ s ears as the sound designer intended. Notes: • The Center and Subwoofer distances can be set up to 5 ft.
42 First Time Setup —Continued Speaker Level Calibration Here you can adjust the lev el of each speaker with the b uilt-in test tone so that the v olume of each speaker is the same at the listening position.
43 First Time Setup —Continued If you connect an -compatible Integra MiniDisc recorder or CD recorder to the T APE IN/OUT jacks, for to work properly , you must change this setting.
44 Basic Operation This section explains ho w to select the input source (i.e., the A V component that you want to listen to or watch). Selecting the Input Source Standby Zone 2 1 3 On Standby TV Disp.
45 Basic Operation —Continued Y ou can adjust the brightness of the display . Y ou can temporarily mute the output of the A V receiv er. W ith the sleep timer , you can set the A V receiver to auto- matically turn off after a specified period.
46 Basic Operation —Continued Y ou can display various information about the current input source as follows. The following information can typically be displayed for input sources. *If the input signal is analog, no format information is displayed.
47 Basic Operation —Continued W ith the built-in tuner you can enjo y AM and FM radio stations. Y ou can store your fav orite stations as presets for quick selection. Listening to the Radio T uning into Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears.
48 Basic Operation —Continued Presetting Radio Stations Y ou can store up to 40 of your fav orite radio stations as presets. Selecting Preset Stations Deleting Presets Displaying Radio Inf ormation 1 T une into the station that you want to store as a preset.
49 Basic Operation —Continued See “ About the Listening Modes” on page 51 for detailed information about the listening modes. Selecting on the A V receiver ■ [Stereo] button This button selects the Stereo listening mode.
50 Basic Operation —Continued The following table lists all the listening modes and sho ws which modes can be selected for each input signal format. Input signal format Analog, PCM*1 1. In the Direct listening modes, PCM signals at 32 kHz, 44.1 kHz, and 48 kHz are processed at 64 kHz, 88.
51 Basic Operation —Continued About the Listening Modes W ith its built-in surround-sound decoders and DSP pro- grams, the A V receiver can transform your home listen- ing room into a movie theater or concert hall. Direct The selected input source is output by the front left and right speakers only , with minimal processing for a pure sound.
52 Ad v anced Operation W ith the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts ev en when listening at low v olume lev els—ideal for watching movies late at night when you don’t w ant to disturb anyone.
53 Adv anced Operation —Continued Y ou can adjust the level of indi vidual speakers during playback. These adjustments are temporary and will be cancelled when the A V receiver is set to Standby . Notes: •Y ou cannot use this function while the A V receiver is muted.
54 Adv anced Operation —Continued This section explains ho w to record the current input source, how to record one input source while enjo ying another , and how to dub audio onto your video record- ings.
55 Adv anced Operation —Continued AV Recording Y ou can record A V input sources to an A V recording component (VCR, etc) connected to the VIDEO 1 OUT or VIDEO 2 OUT .
56 Ad v anced Setup Here are surround-related settings for PCM, Dolby Dig- ital, multichannel, and other input signal formats. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button.
57 Adv anced Setup —Continued 3-3. DTS These settings apply to DTS input signals. ■ a. LFE Level W ith this setting you can set the lev el of the LFE (Low Frequency Ef fects) channel for DTS sources to – ∞ , –10 dB, or 0 dB (default).
58 Adv anced Setup —Continued 4-1. Mono ■ a. Output Channel This setting determines which speakers are used to out- put mono audio when the Mono listening mode is used. L/R: Mono audio is output from the front left and right speakers (default). Center: Mono audio is output from the center speaker .
59 Adv anced Setup —Continued ■ e. Virtual Surr Level W ith this setting, you can adjust the lev el of virtual sur- round sound from –3 dB to +3 dB (default is 0 dB). If the clarity is poor , or the effect sounds unnatural, you may be able to improv e it by lowering this setting.
60 Adv anced Setup —Continued This section explains the items on the Preference menu. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. 6-1. IntelliV olume W ith this preference, you can set the input lev el for each input source.
61 Adv anced Setup —Continued 6-3. OSD Setup ■ a. Immediate Display This preference determines whether or not actions, such as selecting an input source, are displayed onscreen. Normal: Actions displayed. Select this if you ha ve a standard 4:3 TV .
62 Adv anced Setup —Continued If sev eral Integra components are used in the same room, the remote controller’ s control codes may o verlap with those of another component. T o dif ferentiate the remote controller’ s control codes, you can change its ID to another number .
63 Zone 2 W ith the Zone 2 function, you can enjoy one input source in the main room and a different source in another room. There are two connection methods: using a recei ver/inte- grated amp in Zone 2 or using only a pair of speakers in Zone 2. Using a Receiver/Integrated Amp in Zone 2 W ith this connection method, you can use 5.
64 Zone 2 —Continued To use Zone 2, you must make this setting. It enables the speakers connected to the ZONE 2 SPEAKERS termi- nals so that they produce sound when Zone 2 is used. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button.
65 Zone 2 —Continued The ZONE 2 OUT L/R jacks can also be used as pre outs. Setting the Zone 2 Out 1 Press the [Receiver] button f ol- lowed b y the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “1.
66 Zone 2 —Continued Here you can turn on Zone 2, select an input source, and adjust the volume. Note: To control Zone 2 with the remote controller , you must press the [ZONE 2] button first. Notes: • If the Sleep function has been set, the Zone 2 compo- nent will turn off along with the A V receiv er when the specified sleep time expires.
67 Zone 2 —Continued Using the 12V T rigger When the A V receiver’ s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V TRIGGER IN jack on a connected component, the A V receiver can be configured so that the component is turned on automatically when Zone 2 is used.
68 Zone 2 —Continued Using a Multiroom Kit with a Cabinet In the following diagram, an IR recei ver picks up the infrared signals from the remote controller and feeds them to the A V receiver in the cabinet via the connecting block. • On the Remote Setup menu, set the IR IN Position set- ting to “Main” (see page 61).
69 Contr olling Other Components Y ou can use the A V Receiver’ s remote controller (RC- 587M) to control your other components, including those made by other manufacturers. This chapter explains ho w to: • Enter the remote control code for a component that you want to control (e.
70 Controlling Other Components —Continued Resetting Remote Mode Buttons If you’ ve entered another code for one of these b utton and now w ant to return to the default, perform the fol- lowing procedure. By default, some REMO TE MODE b uttons are prepro- grammed with remote control codes for controlling Inte- gra components connected via .
71 Controlling Other Components —Continued Remote Control Codes When two or more codes are gi ven, try each one in turn, and choose the one that works best. Depending on the manufacturer and component, the remote controller may not work as expected.
72 Controlling Other Components —Continued SA T (satellite receiver) Manufacturer Control code Tr istar 4016 Unisat 4013 Universum 4021, 4024 Vo r tec 4017 Wela 4025 Zehnder 4020 Zenith 4032 CBL (ca.
73 Controlling Other Components —Continued VCR Manufacturer Control code RCA 2001, 2002, 2003, 2008, 2010, 2013, 2021, 2023, 2025, 2026, 2027 Realistic 2007, 2008, 2010, 2011, 2012, 2017 Rex 2048 Ro.
74 Controlling Other Components —Continued TV Manufacturer Control code Loewe 1014, 1040, 1055 Luxman 1004, 1006 LXI 1001, 1006, 1010, 1014, 1016, 1017, 1034 M Electronic 1035, 1053, 1062, 1063 Magn.
75 Controlling Other Components —Continued To control another component, point the remote control- ler at it and use the buttons as e xplained below (you must select the appropriate remote control mode first).
76 Controlling Other Components —Continued Controlling a VCR The following b uttons control the A V Receiv er . [V OL]: Adjusts the v olume of the A V receiv er. [Muting]: Mutes the A V Receiv er . Controlling a Satellite Receiver The following b uttons control the A V Receiv er .
77 Controlling Other Components —Continued The A V receiver’ s remote controller can learn the com- mands of other remote controllers simply by pointing them at each other .
78 Controlling Other Components —Continued W ith the Macro function, you can program the remote controller’ s Macro b uttons to perform a sequence of actions with just one button press. F or example, nor - mally you need to perform the following actions to play a CD: 1.
79 Tr oub leshooting If you hav e any trouble using the A V receiver, look for a solution in this section. If you can’t resolv e the issue yourself, contact the dealer from whom you purchased this unit. Can’t turn on the A V receiver? • Make sure that the po wer cord is properly plugged into the wall outlet.
80 Tr oubleshooting —Continued The subwoof er produces no sound? • When you play source material that contains no infor- mation in the LFE channel, the subwoofer produces no sound.
81 Tr oubleshooting —Continued Reception is noisy , FM stereo reception is noisy , or the FM STEREO indicator doesn’t appear? • Relocate your antenna. •M ove the A V receiv er away from your TV or com- puter . • Listen to the station in mono (page 47).
82 Tr oubleshooting —Continued The sound changes when I connect m y head- phones? • When a pair of headphones is connected, the listening mode is set to Stereo, unless it’ s already set to Stereo or Direct. When you disconnect the headphones, the previous listening mode will be resumed.
83 Specifications Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs ■ Other Jacks Specifications and features are subject to change without notice.
84 SN 29343826 (C) Copyright 2004 ONKY O CORPORA TION Japan. All rights reserved. I0408-1 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.
Ein wichtiger Punkt beim Kauf des Geräts Integra DTR-4.5 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Integra DTR-4.5 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Integra DTR-4.5 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Integra DTR-4.5 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Integra DTR-4.5 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Integra DTR-4.5 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Integra DTR-4.5 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Integra DTR-4.5. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Integra DTR-4.5 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
