Benutzeranleitung / Produktwartung SP8600 des Produzenten InFocus
Zur Seite of 51
.
Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the autho r.
SP8600 User's Manual — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector.
Preface Projector Installation Notice ¾ Place the projector in a horizontal p osition The tilt angle of the projector should not excee d 15 degrees, nor should the proje ctor be installed in any way other than the desktop and ceiling mou nt, ot herwise lamp life could decrease dramatically.
SP8600 User's Manual Replacing the Lamp Replacing the lamp can b e hazardous if done in correctly. See Replacing the Proje ction Lamp on page 29 for clear and safe instructi ons for this procedure. Before replacing the lamp: ¾ Unplug the power cord.
Preface – v – Table of Contents GETTING STARTED .......................................................................................................................................................... 1 P ACKING C HECKLIST ......................
SP8600 User's Manual — vi — SPECIFICATIONS ............................................................................................................................................................. 39 S PECIFICATIONS ......................
SP8600 User's Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: DLP P ROJECTOR R EMOTE CONTR OL ( BATTERY NOT I.
SP8600 User's Manual Views of Projector Parts Front-right View 1 34 5 6 7 2 I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Height-adj uster butto n Push to release height adjust er 2. Height adjuster Adjust level of projector 12 3. Lens Projection Lens 4.
SP8600 User's Manual Top view—On-screen Display (OSD) buttons and LEDs Source Menu Enter Re-sync 11 10 12 1 2 4 5 6 3 7 8 9 I TEM L ABEL D ESCRIPTIO N S EE PAGE : Green Power On / Standby 1. Power LE D Off Power Off (AC Off) Red Lamp is ready to be powered-on.
SP8600 User's Manual Rear view 12 3 4 5 6 7 8 9 1 0 11 12 13 14 15 16 I TEM L ABEL D ESCRIPTIO N S EE PAGE : 11 1. AC IN Connect the power cord 2. Connect a USB cable from a computer (USB) 3. COMPONENT Connect a compone nt video enable d device 4.
SP8600 User's Manual Bottom view 51.5 65.0 71.0 90.5 109.0 76.0 2 1 3 4 2 Ceiling Mount M4x8 (Max L=12mm) I TEM L ABEL D ESCRIPTION S EE PAGE : 12 1. Tilt adjustor Rotate adju ster lever to adjust angle po sition. 2. Ceiling support ho les Contact your dealer for information on mounting the projector on a ceiling 3.
SP8600 User's Manual Remote Control Par ts Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the re mote control and the proj ector.
SP8600 User's Manual – 7 – I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Up cursor Navigate and c hange settings in the OSD 2. Enter Change settings in the OSD 15 3. Power Turn the projector O n or Off 11 4. Right curs or Navigate and c hange settings in the OSD 15 5.
SP8600 User's Manual – 8 – Remote Control Operating Range The projector receives infrared signals from the remote control. It is not necessa ry to point the remote directly at the projector.
SP8600 User's Manual – 9 – S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A) . Pull out the cover (B) . 2. Insert the battery (not included) with the positive side facing up.
SP8600 User's Manual Connecting Input Devices A PC or note book computer and video devices can be connected to the projector at the same time. Video devices include DVD , VCD, and VHS players, as we ll as movie camc orders and digi tal still camera s.
SP8600 User's Manual Starting and Shutting down t he Projec tor 1. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED will be on. 2. Turn on the connected devices. 3. Ensure the POWER LED displays a solid green and not a flashing green.
SP8600 User's Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector t able or stand should be level and sturdy . • Position the projector so that it is perpendicular t o the screen. • Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle.
SP8600 User's Manual Adjusting the Zoom ring, Focus and Keystone – 13 – 1. Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size B . 2. Use the Image-focus control (on the projector only) to sharpen the pro- jected image .
SP8600 User's Manual Adjusting the Volume 1. Source Menu Enter Re-sync Press the Volume +/- buttons on the remote control. The volume control appears on the display. 2. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/- . 3.
SP8600 User's Manual – 15 – O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote control curs or buttons or the buttons on the top of the projector to navigate and make changes to the OSD.
SP8600 User's Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic . 2. Press the cursor ▲▼ button until Language is highlighted.
SP8600 User's Manual OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. – 17 –.
SP8600 User's Manual PICTURE>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic menu.
SP8600 User's Manual PICTURE>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu.
SP8600 User's Manual HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu. I TEM D ESCRIPTIO N Press the ◄► buttons to set the Primary Color. Notes: There are six s ets ( R / G/ B/ C/ M/ Y) of colors to be custom ized. Primary Color Hue Press the ◄► buttons to adjust the Hue.
SP8600 User's Manual DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings.
SP8600 User's Manual PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected.
SP8600 User's Manual SETUP>> Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu. Press ◄► to change values for settings.
SP8600 User's Manual Menu Settings Press the ENTER button to enter the Menu Settings sub menu. I TEM D ESCRIPTIO N Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center / Bottom-Left/ Bottom-Right. Menu Position Press the ◄► buttons to set the Menu Display timer before the OSD times out.
SP8600 User's Manual SETUP>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Advanced menu.
SP8600 User's Manual Audio Press the ENTER button to enter the Audio sub menu. I TEM D ESCRIPTIO N Volume Press the ◄► buttons to adju st the audi o Volum e. Bass Press the ◄► buttons to ad just the audi o Bass. Treble Press the ◄► buttons t o adjust t he audio Tr eble.
SP8600 User's Manual HDMI Press the ENTER button to enter the HDMI sub menu. I TEM D ESCRIPTIO N Press the ◄► buttons to select from three HDMI display formats: Auto/ PC signal/ Video signal. HDMI Form at HDMI Amplifier Gain Press the ◄► buttons to adjust HDMI Amplifier Gain.
SP8600 User's Manual STATUS Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the STATUS Menu . I TEM D ESCRIPTIO N Source Displays the activated input source. Resolution Displays the current resolution of input source.
SP8600 User's Manual – 29 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, which you can order from your local dealer.
SP8600 User's Manual 3. Remove the lamp compart- ment cover. 4. Remove the three screws from the lamp module. 5. Lift the module handle up. 6. Pull firmly on the module handle to remove the lamp module.
SP8600 User's Manual 7. Reverse steps 1 to 6 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be con- nected properly before tightening the screws.
SP8600 User's Manual – 32 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn.
SP8600 User's Manual Using the Kensingt on ® Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensi ngton security cable.
SP8600 User's Manual – 34 – T ROUBLESHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance.
SP8600 User's Manual – 35 – LED Error Messages E RROR C ODE M ESSAGES P OWER LED B LINK L AMP LED B LINK T EMP LED B LINK Lamp Ready ON ON OFF Start (AC Power standby) ON OFF OFF Cooling ON f.
SP8600 User's Manual – 36 – Problem: The image is flat with no contrast Adjust the Contrast setting on the Image menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.
SP8600 User's Manual – 37 – Audio Problems Problem: There is no sound 1. Adjus t the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers.
SP8600 User's Manual – 38 – HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announ ced that cables would be tested as Standard or High- Speed cables.
SP8600 User's Manual – 39 – S PECIFICATIONS Specifications SP8600 Model Display type TI DLP DMD 0.65” Native Resolution 1920 x 1080 Weight 3.4 kg (7. 5 lbs) Projection distance 1 meters ~ 10 meters Projection screen size 30" ~ 30 0" Projection lens Manual Focus/ Manual Zoom Zoom ratio 1.
SP8600 User's Manual Projection Distance vs. Projection Si ze Projection Distance and Size Table – 40 – 16:9 SCREEN PROJECTION DISTANCE DIAGONAL WIDTH HEIGHT INCH MM MM MM MIN LENGTH (WITH MA.
SP8600 User's Manual – 41 – Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) NTSC — 15.
SP8600 User's Manual – 42 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) 720p 37.5 50.0 — O — O 720p 45.0 60.0 — O — O 1080i 33.8 60.0 — O — O 1080i 28.1 50.0 — O — O 1080p 67.
SP8600 User's Manual Projector Dimensions 326 mm 254 mm 104 mm 98 mm – 43 –.
SP8600 User's Manual – 44 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules.
Ein wichtiger Punkt beim Kauf des Geräts InFocus SP8600 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie InFocus SP8600 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für InFocus SP8600 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von InFocus SP8600 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über InFocus SP8600 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon InFocus SP8600 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von InFocus SP8600 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit InFocus SP8600. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei InFocus SP8600 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
