Benutzeranleitung / Produktwartung iPW1EURO des Produzenten Icom
Zur Seite of 24
iPW1 iPW1EURO HF/50 MHz ALL BAND 1 kW LINEAR AMPLIFIER INSTRUCTION MANUAL.
R W ARNING HIGH VOL T AGE! NEVER attach an antenna or internal antenna connector dur- ing transmission. This may result in an electrical shock or burn. R W ARNING! NEVER carry the linear amplifier by yourself. At least two persons must carry the linear amplifier since it weights approx.
IMPORT ANT ...................................................... i PRECAUTION ................................................... i EXPLICIT DEFINITIONS ................................. ii T ABLE OF CONTENTS .................................. ii SUPPLIED ACCESSORIES .
1 1 P ANEL DESCRIPTION ■ Front panel and remote controller 0 100 250 500 1K 1.5 K 0 TEMP ALC ALC adj SWR 0 1 1.5 2 3 10 20 30 40 50 60 V D HOT I D Po 10 20 30 40 50 60 W A METER-1 METER-2 P o TEMP I D V D ALC SWR DOWN 1 .
2 1 P ANEL DESCRIPTION q POWER SWITCH [POWER] (p. 12) Push momentarily to turn power ON. w TRANSMIT INDICA TOR [TRANSMIT] (p. 16) Lights green while transmitting. During transmission, a humming may sound depending on the output power . This is caused by the large current produced by the power sup- ply and does not indicate equipment malfunc- tion.
3 1 P ANEL DESCRIPTION ■ Rear panel q OUTPUT ANTENNA CONNECTORS [ANT1] – [ANT4] (p. 6) Accept a 50 Ω antenna with a PL-259 connector . w ACCESSOR Y SOCKET -1 [ACC-1] ACCESSOR Y SOCKET -2 [ACC-2] Enable connection to Icom exciters (transceivers).
4 1 P ANEL DESCRIPTION D ACC-1 SOCKET D ACC-2 SOCKET (w/[EXCITER] is “ 1 ” ) The following descriptions are applied when the [EXCITER] switch is set to “ 1 ” (default). When [EXCITER] is set to “ 1&2, ” [ACC-2] functions the same as [ACC-1] above for the 2nd exciter .
5 2 INST ALLA TION AND CONNECTIONS ■ Unpacking After unpacking, immediately report any damage to the delivering carrier or dealer . Keep the shipping cartons. For a description and a diagram of accessory equip- ment included with the IC-PW1/EURO, see SUP- PLIED ACCESSORIES on p.
■ Grounding T o prevent electrical shock, television interference (TVI), broadcast interference (BCI) and other prob- lems, ground the linear amplifier through the GROUND terminal on the rear panel. For best results, connect a heavy gauge wire or strap to a long earth-sunk copper rod.
■ System interconnections 1 or 2 Icom 100 W HF transceivers can be connected as exciters to the IC-PW1/EURO. Non-Icom trans- ceivers can be used, however , band selection will not be synchronized for each exciter . See the following diagrams for making connections between the IC-PW1/EURO and an exciter (transceiv- er).
8 2 INST ALLA TION AND CONNECTIONS • Using a 13-pin ACC socket (IC-706 series) IC-PW1/EURO Ground Coaxial cable (supplied) ACC cable (supplied) Remote control cable (supplied) To an antenna ANT ACC-.
9 2 INST ALLA TION AND CONNECTIONS • Using 1 Icom and 1 non-Icom exciters (transceivers) NOTE: The speci fi cations for the SEND relay are 5 V DC 0.
10 2 INST ALLA TION AND CONNECTIONS • Using non-Icom exciters (transceivers) when the IC-PW1/EURO ’ s power is OFF T o use the antenna selector of the IC-PW1/EURO while the power is OFF , follow 1 of 2 methods. (1) Supply the antenna selector power to the ACC-1 socket Supply the 13.
11 2 INST ALLA TION AND CONNECTIONS The control section of the linear ampli fi er can be sep- arated from the main body , doubling as a remote con- troller . It can be placed on the exciter or in another convenient place. q Disconnect the AC power cable.
12 3 OPERA TION ■ Setting the ALC levels Before fi rst applying power , make sure all connec- tions required for your system are complete by refer- ring to chapter 2. Then, reset the linear ampli fi er using the following procedure. NOTE: Resetting CLEARS all programmed set- tings to default values.
13 3 OPERA TION The IC-PW1/EURO uses CI-V frequency data for automatic selection of the operating band. Program the exciter ’ s address to use this capability as follows: For non-Icom exciters, the IC-PW1/EURO cannot be controlled using the CI-V function, so this set- ting is not necessary .
14 3 OPERA TION ■ Programming the CI-V address (continued) D Setting the IC-PW1/EURO ’ s address It is not necessary to change the IC-PW1/EURO ’ s default CI-V address of 54H. However , if desired, the address can be changed using the internal address switch illustrated below .
15 3 OPERA TION t Push [DOWN] to turn the position memory function for the [INPUT] select switch ON. • The band indicators, [1.8] – [50], light continuously . y Rotate the 1st exciter ’ s dial until the LED [INPUT z ] lights continuously . u T urn the 2nd exciter ’ s power ON.
16 3 OPERA TION CAUTION: DO NOT operate the IC-PW1/EURO before adjusting the ALC levels properly with the [ALC adj1] and [ALC adj2] pots. (p. 1 1) It takes 15 sec. for CI-V line initial settings when several CI-V devices (more than 5) are connected to a CI-V line.
17 3 OPERA TION This linear ampli fi er has various protection circuits. D ALC circuit The ALC (Automatic Level Control) circuit automati- cally limits RF output power by controlling the input level of the exciter . This prevents transmission of dis- torted signals when the input signal level exceeds the allowable level.
18 4 MAINTENANCE ■ T roubleshooting The following chart is designed to help you correct problems which are not equipment malfunctions. If you are unable to locate the cause of a problem or solve it through the use of this chart, contact your nearest Icom Dealer or Service Center .
5 SPECIFICA TIONS 19 ■ General • Frequency coverage: 0 1.800 – 0 1.999 MHz 0 3.500 – 1 3.999 MHz 0 7.000 – 1 7.300 MHz 10.100 – 10.150 MHz 14.000 – 14.350 MHz 18.068 – 18.168 MHz 21.000 – 21.450 MHz 24.890 – 24.990 MHz * 1 28.000 – 29.
20 5 SPECIFICA TIONS INST ALLA TION NOTES For amateur base station installations it is recom- mended that the forwards clearance in front of the an- tenna array is calculated relative to the EIRP (Effective Isotropic Radiated Power).
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-5449G-1EX- r Printed in Japan © 1997 – 2007 Icom Inc. Printed on recycled paper with soy ink..
Ein wichtiger Punkt beim Kauf des Geräts Icom iPW1EURO (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Icom iPW1EURO noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Icom iPW1EURO - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Icom iPW1EURO reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Icom iPW1EURO erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Icom iPW1EURO besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Icom iPW1EURO verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Icom iPW1EURO. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Icom iPW1EURO gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
