Benutzeranleitung / Produktwartung IC-R1500 des Produzenten Icom
Zur Seite of 56
INSTRUCTION MANUAL iR1500 COMMUNICA TIONS RECEIVER.
i FOREWORD Thank you for purchasing this Icom receiver . The IC-R1500 COMMUNICA TIONS RECEIVER is designed and built with Icom’s state of the art technology and craftsmanship. With proper care, this receiver should provide you with years of trouble- free operation.
ii R W ARNING! NEVER connect the receiver via the OPC-254L to an AC outlet. This may pose a fire hazard or re- sult in an electric shock. R W ARNING! NEVER operate the receiver while dri- ving a vehicle. Safe driving requires your full attention— any- thing less may result in an accident.
iii T ABLE OF CONTENTS FOREWORD ........................................................................................... i IMPORT ANT ............................................................................................ i EXPLICIT DEFINITIONS .
iv 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ AFC function ................................................................................ 13 ■ VSC function ................................................................................ 13 ■ IF filter selection .
1 CONNECTION 1 ■ Rear panel connection D DC power supply connection Use a 12 V DC power supply with at least 4 A capacity . Make sure the ground terminal of the DC power supply is grounded. • CONNECTING TO A DC POWER SUPPL Y OPC-254L (optional) black white R CAUTION! NEVER remove the fuse- holders from the DC power cable.
2 1 CONNECTION 1 D D OPC-1 156 connection q Connect the controller plug to the OPC-1 156 jack. w Detach the ferrite core from the controller cable, then at- tach it to the OPC-1 156 as shown below . • Make sure to wind the cable on the ferrite core.
3 P ANEL DESCRIPTION 2 q SET•LOCK KEY [SET•LOCK] ➥ Push to enter set mode . (p. 35) ➥ Push and hold for 1 sec. to turn the lock function ON and OFF . (p. 1 1) w TUNING STEP/MODE KEY [TS•MODE] ➥ Push to enter tuning step selection mode . (p.
4 2 PA NEL DESCRIPTION 2 y MONITOR•T ONE•TONE SCAN KEY [MONI•T/T -SCAN] ➥ Push to turn the monitor function ON and OFF . (p. 1 1) ➥ Push and hold for 1 sec.
5 2 PA NEL DESCRIPTION q AFC INDICA TOR Appears when the AFC function is in use. (p. 13) w FM CENTER INDICA TORS ➥ “” or “ ” appears when the received signal is not tuned to its center frequency; or the squelch is closed. ➥ “” appears when the received signal is tuned to its center frequency .
6 2 PA NEL DESCRIPTION 2 y DSP INDICA TOR (p. 43) Appears when the DSP digital filter function is in use. • The DSP function requires an optional UT -106 installation . u FREQUENCY READOUT Shows the operating frequency , channel names, set mode contents, etc.
7 2 PA NEL DESCRIPTION q ANTENNA CONNECTOR [ANT] Connects a 50 Ω antenna with a BNC connector and a 50 Ω coaxial cable. w P ACKET JACK [P ACKET] Connects a TNC (T erminal Node Controller), etc. for data communications. The receiver can support 9600 bps packet communication (AFSK).
8 3 SETTING A FREQUENCY 2 3 ■ T urning power ON/OFF ➥ While receiver ’s power is OFF , push [PWR] to turn power ON. • While receiver power is ON, push and hold [PWR] for 1 sec. to turn power OFF . ■ Mode selection D VFO modes VFO mode is used for the desired frequency setting within the frequency coverage.
9 3 SETTING A FREQUENCY ■ T uning step selection When using the tuning dial to change the frequency , or when a scan function is activated, the frequency changes in incre- ments determined by the set tuning step. This can be changed if desired. The following tuning step are available.
10 3 SETTING A FREQUENCY 3 ■ Receive mode selection Receive modes are determined by the physical properties of the radio signals. The receiver has 6 receive modes: LSB USB, CW , AM, WFM and FM modes. The mode selection is stored independently in each memory channels.
11 BASIC OPERA TION 4 ■ Receiving q Push and hold [PWR] for 1 sec. to turn power ON. w Set the audio level. ➥ Push [MONI•T/T -SCAN] to open the squelch. ➥ Rotate [VOL] to adjust the audio level. ➥ Push [MONI•T/T -SCAN] to close the squelch.
12 4 BASIC OPERA TION 4 ■ Attenuator function The attenuator prevents a desired signal from being distorted when very strong signals are near the desired frequency or when very strong RF fields, such as from a broadcasting sta- tion, are near your location.
13 4 BASIC OPERA TION ■ AFC function [ The AFC (Automatic Frequency Control) function tunes the displayed frequency automatically when an off-center fre- quency is received. It activates in FM mode and only when the selected IF filter is 6 kHz or 15 kHz.
14 4 BASIC OPERA TION 4 ■ IF filter selection [ The receiver has 2 to 4 IF passband filter widths for each mode. Selectable passband widths are 3, 6, 15, 50 and 230 (depending on the selected mode). • Selectable passband width for each mode. SSB mode : 3 (2.
15 4 BASIC OPERA TION Duplex communication uses two different frequencies for trans- mitting and receiving. Generally , duplex is used in communi- cation through a repeater , some utility communications, etc. During duplex operation, the transmit station frequency is shifted from the receive station frequency by the offset fre- quency .
16 5 MEMOR Y OPERA TION 4 5 ■ General description The receiver has 1 100 memory channels including 100 scan edge memory channels (50 pairs) for storage of often-used frequencies. And a total of 21 memory banks, A to H, J to R, T, U, W and Y are available for storing groups of frequencies, etc.
17 5 MEMORY OPERA TION VFO settings, including the set mode contents such as sub- audible tone frequency , offset and scan skip information can be programmed into a memory channel. q Push [V/MHz•SCAN] to select VFO mode . w Set the desired frequency using [DIAL] .
18 5 MEMORY OPERA TION 5 ■ Programming channel names Each memory channel can be programmed with an alphanu- meric channel name for easy recognition and can be indi- cated independently by channel. Names can be a maximum of 6 characters— see the table below for available charac- ters.
19 5 MEMORY OPERA TION D D To indicate the channel name [ The channel name indication can be set independently for eace memory channel. q Select the desired memory channel. ➥ Push [MR•SKIP] to select memory mode , then rotate [DIAL] to select the desired memory channel.
20 5 MEMORY OPERA TION 5 [EXAMPLE]: T ransferring the contents of memory channel 30 to VFO. [EXAMPLE]: T ransferring the contents of memory channel 22 to channel 23. Select the target channel. Push . Rotate for selecting memory channel. Push for 1 sec.
21 5 MEMORY OPERA TION ■ Memory clearing Contents of programmed memories can be cleared (erased), if desired. q Push [V/MHz•SCAN] to select VFO mode . w Push [S.MW•MW] to enter select memory write mode . •“ ! ” and the memory channel number blink.
22 5 MEMORY OPERA TION 5 The IC-R1500 has a total of 21 banks (A to H, J to R, T , U, W, Y). Regular memory channels, 0 to 999, may assigned into the desired bank for easy memory management. q Select the desired memory channel. ➥ Push [MR•SKIP] to select memory mode , then rotate [DIAL] to select the desired memory channel.
23 5 MEMORY OPERA TION ■ Memory bank selection q Push [MR•SKIP] to select memory mode . w Push [MR•SKIP] again to enter memory type selection mode . e Rotate [DIAL] to select the desired bank (A to H, J to R, T , U, W or Y). • Only programmed banks are displayed.
24 5 MEMORY OPERA TION 5 e Push [TS•MODE] once to select “bAnk.” • The bank’s indicator and bank channel are displayed. r Rotate [DIAL] to select the desired bank indicator to trans- fer or erase. • Push [SET•LOCK] to toggle the bank or bank channel selection.
25 SCAN OPERA TION 6 ■ Scan types Scanning searches for signals automatically and makes it easier to locate new stations. There are 5 scan types and 4 resume conditions to suit your operating needs. FULL SCAN (p. 26) Repeatedly scans all frequen- cies over the entire band.
26 6 SCAN OPERA TION 6 ■ Scan start/stop D Preparation Scan resume condition (p. 29); program scan edges (p. 27); program two or more memory channels (p. 17); set skip set- tings (p. 28), if desired. D Operation q Push [V/MHz•SCAN] to select VFO mode for full/pro- grammed scan; or push [MR•SKIP] to select memory mode for memory/bank scan.
27 6 SCAN OPERA TION ■ Scan edges programming Scan edges can be programmed in the same manner as memory channels. Scan edges are programmed into scan edges, 0A/0B to 49A/49B, in memory channels. q Push [V/MHz•SCAN] to select VFO mode . w Set the edge frequency of the desired frequency range: ➥ Set the frequency using [DIAL] .
28 6 SCAN OPERA TION 6 ■ Skip scan D Skip channel/frequency setting Y ou can set the selected memory channel as a skip channel which is skipped during memory skip scan. In addition, it can be set as a skip channel for both memory skip scan and fre- quency skip scan.
29 6 SCAN OPERA TION The scan resume condition can be selected a timed or pause scan. The selected resume condition is also used for priority watch. (p. 30) q Push [SET•LOCK] to enter set mode . w Push [SET•LOCK] or [S.MW•MW] several times until “SCt” or “SCP” appears.
30 7 PRIORITY W A TCH 6 7 ■ Priority watch types Priority watch checks for signals on the frequency every 5 sec. while operating on a VFO frequency or scanning. The receiver has 2 priority watch types to suit your needs. The watch resumes according to the selected scan resume condition.
31 POCKET BEEP AND T ONE SQUELCH 8 ■ Pocket beep operation This function uses subaudible tones for calling and can be used as a “common pager” to inform you that someone has called while you were away from the receiver . D Wa iting for a call from a specific station q Set the operating frequency in FM mode.
32 8 POCKET BEEP AND T ONE SQUELCH 8 i Push any key to exit tone squelch selection mode . o When a signal with a matching tone is received, the re- ceiver emits beep tones and blinks “ S .” • Beep tones sound for 30 sec. and “ S ” blinks. T o stop the beeps and blinking manually , push any key .
33 8 POCKET BEEP AND T ONE SQUELCH ■ T one/DTCS squelch operation The tone or DTCS squelch opens only when receiving a sig- nal with the same pre-programmed subaudible tone or DTCS code. Y ou can silently wait for a signal using the same tone. q Set the operating frequency in FM mode.
34 8 POCKET BEEP AND T ONE SQUELCH 8 ■ T one scan By monitoring a signal using with pocket beep, tone or DTCS squelch, you can determine the tone frequency or DTCS code necessary to open the squelch. q Set the desired operating frequency or memory channel to be checked for a tone frequency or code.
† Appears when accessing set mode from VFO mode only. ‡ Appears when accessing set mode from memory mode only. When the UT-106 is installed • Key-touch beep • Display dimmer • Auto power OFF.
• Weather alert * 1 • TSQL frequency • DTCS code • DTCS polarity • Offset frequency • Duplex direction • Display contrast • Scan resume timer • VSC function * 5 • AFC function * 2 .
37 9 SET MODE D D Key-touch beep The key-touch beep can be turned OFF for silent operation. (default: ON) Even when this item is set to OFF , the power-on beep and pocket beep function still sound.
38 9 SET MODE 9 D D Display color The display color can be set to amber (default), yellow or green. D D Display contrast The LCD contrast can be adjusted through 9 levels.
39 9 SET MODE D D T one frequency Sets subaudible tone frequency for tone squelch operation. T otal of 51 tone frequencies (67.0–254.1 Hz) are available. (default: 88.5 Hz) •A vailable tone frequency list D D DTCS code Sets DTCS code for DTCS squelch operation.
40 9 SET MODE 9 D D VSC setting T urns VSC (V oice Squelch Control) ON and OFF . (default: OFF) D D Scan resume timer Selects scan resume timer from SCT -15 (default), SCT -10, SCT -5 and SCP-2. Scan resumes after the specified period when the received signal disappears.
41 9 SET MODE D D Memory name setting Sets memory name appearance ON (appear) and OFF (does not appear; default). This item appears when set mode is accessed from memory mode only . D D Memory bank link function Sets the memory bank link function ON and OFF (default).
42 9 SET MODE 9 D D AFC setting T urns AFC (Automatic Frequency Control) function ON and OFF . (default: OFF) D D Filter setting Select the IF filter passband width from 3, 6, 15, 50 and 230 (depending on the selected mode.) D D W eather alert function T urns weather alert function ON and OFF .
43 9 SET MODE D D ANF setting Tu rns ANF (Automatic Notch Filter) function ON and OFF . The ANF function automatically attenuates up to 3 beat tones, tuning signals, etc. even if they frequency varies. The ANF function can be used in SSB, AM, FM and WFM modes.
44 10 OTHER FUNCTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D D W eather channel selection q Push [MR•SKIP] twice and rotate [DIAL] to select weather channel group, then push [MR•SKIP] again. w Rotate [DIAL] to select the desired weather channel.
D D ANF function [ The ANF (Automatic Notch Filter) function automatically at- tenuates beat tones, tuning signals, etc., even if they are moving. This function can be activated in SSB, AM, FM modes. q Select any of SSB, AM or FM mode. w Push [SET•LOCK] to enter set mode .
46 10 OTHER FUNCTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Cloning allows you to quickly and easily transfer the pro- grammed contents from a personal computer to a receiver using the IC-PCR1500 control software.
47 10 OTHER FUNCTIONS ■ Partial reset If you want to initialize the operating conditions (VFO fre- quency , VFO settings, set mode contents) without clearing the memory contents, a partial reset function is available. ➥ While pushing [V/MHz•SCAN] and [SET•LOCK] , push and hold [PWR] for 1 sec.
48 10 OTHER FUNCTIONS 10 The internal switch must be set properly to use an external speaker , headphones or earphone. Before removing the top cover , turn the receiver power OFF , then disconnect the DC power cable. q Tu rn the power OFF , then disconnect the DC power cable.
49 TROUBLESHOOTING 11 PROBLEM POSSIBLE CAUSE SOLUTION REF . If your receiver seems to be malfunctioning, please check the following points before sending it to a service center . Does not turn on. No sound comes from the speaker . Sensitivity is low and only strong signals are audible.
50 12 DOC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DECLARA TION OF CONFORMITY We Icom Inc. Japan 1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan Declare on our sole responsibility that this equipmen.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6477H-1EX- q Printed in Japan © 2006 Icom Inc. <Intended Country of Use> ■ GER ■ ■ FRA ■ ESP ■ SWE ■ AUT ■ NED ■ POR ■ DE.
Ein wichtiger Punkt beim Kauf des Geräts Icom IC-R1500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Icom IC-R1500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Icom IC-R1500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Icom IC-R1500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Icom IC-R1500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Icom IC-R1500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Icom IC-R1500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Icom IC-R1500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Icom IC-R1500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
