Benutzeranleitung / Produktwartung MFI des Produzenten Ice-O-Matic
Zur Seite of 42
Ice-O-Matic 11100 East 45th Ave Denver, Colorado 80239 Part Number 9081358-01 17-3168-01 Date 10/08 SERVICE AND INSTALLATION MANUAL MFI Series.
.
MFI Series Introduction Page i How To Use This Manual Ice-O-Matic provides this manual as an aid to the end user and service technician in installation and maintenance of the MFI Series ice machines. Do not attempt to perform installation, start-up or maintenance unless you have read and fully understand this manual.
MFI Series Table Of Contents Page ii Table of Contents Introduction ................................................................................................................... ............... Page i Table Of Contents...........................
MFI Series Freight Claim Procedure Page iii Important! Inspect Promptly This merchandise has been carefully inspected and packed in accordance with the carrier’s packing specifications. Responsibility for safe delivery has been assumed by the carrier.
MFI Series Warranty Page iv Ice-O-Matic Parts and Labor Domestic & International L imited Warrant y Mile High Equipment LLC (the “Company”) warr ants Ice-O-Matic brand ice machines, ice di spe.
MFI Series For the Installer Page 1 Installation Guidelines: For proper operation of the Ice-O-Matic ice machine, the following installation guidelines must be followed. Failure to do so may result in loss of production capacity, premature part failures, and may void all warranties.
MFI Series For The Installer Page 2.
MFI Series For the Installer Page 3 Bin Application The MFI Series is designed to fit the following Ice-O-Matic Bins. ● B42, using Bin Top KBT 24 ● B25, B40 B55 using Bin Top KBT19. ● B100 using Bin Top KBT 23 (one unit) or KBT 22 (two units). ● B120, B150, B170-Not designed for MFI Series.
MFI Series For the Installer Page 4 Location: Ice-O-Matic ice machines are designed to be installed indoors in a contro lled environment. Install the ice machine in a location where it has enough space around it t o be accessible for service. A minimum of 6 inches must be allowed at the back for air circulation on air cooled models.
MFI Series For the Installer Page 5 A llow 6 “Clearance for Air Circulation A proper installation locates the ice machine indoors, but in a place where the heat and noise it produces are not objectionable. Air cooled machines discharge hot air out the back and must have a minimum of 6 inches of clearance behind the ice machine.
MFI Series For the Plumber Page 6 Water Inlet: ● Air Cooled Models: The recommended water supply is clean, cold water. Use 3/8 inch O.D. copper tubing, connect to the 3/8 inch male flare at the back of the cabinet. Install a hand valve near the machine to control the water supply.
MFI Series For the Electrician Page 7 Electrical Connections: Check the ice machine nameplate (located on the back panel) for the voltage requirements, and minimum circuit ampacity. The ice machine requires a solid chassis to earth ground. Connect the ice machine to its own electrical circuit so it is individually fused.
MFI Series For the Installer Page 8 Final Check List: _______ 1. Is the ice machine installed indoors in a location where the air and water temperatures are controlled and where they do not exceed the design limitations? _____2. Is there an electrical service disconnect within sight of the installed machine? _____3.
MFI Series Start Up Page 9 Pre-Start Inspection: 1. Remove the front and side service panels. 2. Check that any shipping blocks have been removed. 3. Inspect the interior of the ice machine for loose screws or wires. 4. Check that no refrigerant lines are rubbing each other.
MFI Series Component Description Page 10 ● Control Box: Contains the electrical controls that operate the machine. ● High Pressure Cut Out Switch: An auto-reset switch sensing the high side refrigeration pressure. It will shut the machine off if the discharge pressure e xceeds 450 psig.
MFI Series Component Description Page 11 ● Contactor: A definite purpose contactor connecting the compressor and the fan motor to the po wer supply. ● Circuit Board: Controls the operation of the ice machine using input from the sensors and pressure controls.
MFI Series Component Description Page 12 ● Evaporator: A refrigerated vertical tube filled with water and containing a water seal and auger. ● Auger: A solid stainless steel double spiral auger, it pushes the ice crystals up to the top of the evaporator.
MFI Series Electrical Sequence Page 13 Electrical Sequence: There are 7 indicator lights on the control board: ● WTR-OK: (Water OK) Green . Normal=Glowing. Glow when there is water in the reservoir. ● PWR-OK: (Power OK) Green . Normal=Glowing. Glows when the power board has power and is functional.
MFI Series Operation: Water Page 14 Water enters the machine through the 3/8 inch male flare at the rear of the cabinet, goes to the water reservoir which it enters through the float valve. The water then goes out the botto m of the reservoir tank to the bottom of the evaporator.
MFI Series Operation: Performance Page 15 Beginning at the compressor, the refrigerant is compressed into a high temperature gas. The discharge line directs this gas to the condenser. At the condenser (air or water cooled) the gas is cooled by either air or water and then it condenses into a liquid.
MFI Series Sanitizing and Cleaning Page 16 It is the USER’S RESPONSIBILITY to keep the ice machine and ice storage bin in a sanitary condition. Without human intervention, sanitation will not be maintained. Ice machines also require occa sional cleaning of their water systems with a specifically designed chemical.
MFI Series Bearing Maintenance Page 17 Bearing Maintenance: The bearing in the breaker should also be checked at least two (2) times per year. Switch the machine OFF and check the bearing. 1. Remove the chute cover. 2. Unscrew the ice sweep 3. Removing the water shed and unscrewing the breaker cover.
MFI Series Sensor Maintenance Page 18 Slide Bin Controls to Remove Bin Control Sensor: The bin control uses devices that se nse light, therefore they must be kept clean enough so that they can “see”. At least twice a year, remove the bin control sensors from the base of the chute, and wipe the inside clean, as illustrated.
MFI Series Maintenance: Air Cooled Page 19 Clean the air cooled condenser: Air flow on this model is from front to back, so the inside of the ice mach ine will have to be available to clean the air cooled condenser. Use a vacuum cleaner or coil cleaner if needed.
MFI Series Auger Maintenance Page 20 Auger: In some areas, the water supply to the ice machine will contain a high concentration of minerals, and that will result in an evaporator and auger becoming co ated with these minerals, requiring a more frequent removal than twice per year.
MFI Series Service Diagnosis Page 21 Symptom Possible Cause Probable Correction No ice is made nothing operates. •Unit off due to no power •Restore Power •Unit off due to master switch in OFF •Switch master Switch to ON position •Unit off due to low water level •Check water supply, filter s t r a i n e r , f l o a t v a l v e .
MFI Series Service Diagnosis Page 22 Symptom Possible Cause Probable Correction Unit makes ice, but very slowly •High dischar ge pressure beca use •Clean filter and condenser. of a dirty condenser. •Low capacity because the auger and •Clean the water system.
MFI Series Control System Diagnostics Page 23 The Control System consists of: ● Control Board ● Water Sensors ● Ice Sensors ● High Pressure Cut Out ● Low Pressure Cut Out If the unit is OFF , check the control board: 1. Is the Power OK light on? If not check power to the unit.
MFI Series R&R- Water Reservoir, Bin Control Page 24 Water Reservoir: 1. Disconnect electrical power supply. 2. Shut off water supply to the ice maker. 3. Remove the front panel. 4. Disconnect water inlet tube from reservoir inlet fitting. 5. To remove float valve, push in “locking tabs” as shown and pull float up.
MFI Series R&R-Bearing and Breaker Page 25 Note : Removal of the auger, water seal, evaporator and gear motor must begin at the top of the assembly. To Remove the Breaker Bearing Assembly: 1. Disconnect electrical power. 2. Remove panels. 3. Push back bail clamp and remove ice chute cover.
MFI Series R&R-Auger Page 26 To Remove the Auger: 1. Disconnect electrical power. 2. Turn off the water to the machine. 3. Unclip the evaporator drain hose, pull it down and drain the evaporator into the bin or container. 4. Remove the top panel. 5.
MFI Series R&R-Water Seal Page 27 To Remove the Water Seal: (Assuming all steps to remove the auger have been performed) 1. The gear motor/evaporator assembly will have to be exposed. 2. Remove the four (4) hex head cap screws holding the evaporator to the gear motor assembly.
MFI Series R&R- Evaporator Page 28 To Replace the Evaporator: (Assuming all steps for removal of the thrust be aring, breaker, auger and water seal have been performed). 1. Recover the refrigerant from the ice machine. 2. Unsweat the refrigerant connections: a.
MFI Series R&R-Gear Motor To Check the Gear Motor: 1. Remove wires from terminals 1 and 2 2. Use an ohmeter to check for continuity. If there is none, replace only the motor. If there is continuity but the motor will not start, check the motor’s start switch.
MFI Series R&R-Fan Blade and Motor Page 30 To Remove the Condenser Fan Motor Assembly: 1. Disconnect electrical power to the ice machine 2. Remove top panel and the service panels. 3. Unplug the fan motor wire leadsfrom the fan motors. 4. Remove the two (2)head bolt from the top end of the fan motor assembly.
MFI Series Refrigeration System Service Page 31 Refrigeration Service: General: This ice machine uses R404A refrigerant and polyolester oil. Do NOT use mineral oil in this refrigeration system. ● When the refrigeration system is serviced, a special liquid line drier is re quired.
MFI Series MFI0500 Wiring Diagram Page 32 Wiring Diagram MFI0500 Air, MFI0500 Water.
MFI Series MFI0800 Wiring Diagram Page 33 Wiring Diagram MFI0800 Air, MFI0806 Air, MFI0806 Water W/BK.
MFI Series MFI0805/1255 Wiring Diagram Page 34 Wiring Diagram MFI0805, MFI1255 Air.
MFI Series MFI1256 Wiring Diagram Page 35 Wiring Diagram MFI1256 Air.
MFI Series Service History Page 36 What to Do Before Calling for Service: ● Check the water supply to the ice machine. The ice machine is design ed to shut off if there is no water to it. Check the water filters if there are any. ● Check the power supply to the ice machine.
Ein wichtiger Punkt beim Kauf des Geräts Ice-O-Matic MFI (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ice-O-Matic MFI noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ice-O-Matic MFI - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ice-O-Matic MFI reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ice-O-Matic MFI erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ice-O-Matic MFI besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ice-O-Matic MFI verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ice-O-Matic MFI. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ice-O-Matic MFI gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
