Benutzeranleitung / Produktwartung Rider 318 des Produzenten Husqvarna
Zur Seite of 32
E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 318 Rider 320 A WD Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine.
2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Ser vice journal Pre-deliv er y ser vice ..................................................... 3 After the first 8 hours ......
English – 3 Ser vice journal Pre-deliver y service 1 Charge the batter y f or 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment. 3 Check and adjust tyre pressure . (60 kP a, 0.6 bar , 9 psi). 4 Adjust cutting unit: Adjust lift springs (effectiv e weight of cutting unit should be 12-15kg / 26.
4 – English INTR ODUCTION Dear Customer , Thank y ou f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented ar ticulated steering. Riders are designed f or maximum efficiency e ven in small or confined areas .
English – 5 KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
6 – English KEY T O SYMBOLS Star ting instructions Switch off the engine and take off the ignition cab le bef ore repairs or maintenance Check the engine’ s oil le vel Check tr ansmission oil lev el Lift up the cutting unit Apply the parking brake .
English – 7 WHA T IS WHA T? Location of the contr ols 12 3 4 6 8 7 9 12 14 13 15 10 11 5 1 Speed limiter f or driving forward 2 Speed limiter f or rev ersing 3 Lifting le ver f or the cutting unit 4.
8 – English SAFETY INSTR UCTIONS Saf ety instructions These instr uctions are f or your saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage f or your ne w Rider.
English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hearing protection to minimise the r isk of hearing impairment.
10 – English SAFETY INSTR UCTIONS • Do not tr y to stabilize the machine b y putting your f oot on the ground. • When cleaning the chassis, the machine ma y nev er be driven near v erges or ditches. • When mowing, k eep aw a y from bushes and other objects .
English – 11 SAFETY INSTR UCTIONS • T ake care with battery maintenance. Explosive gases f or m in the batter y . Nev er perform maintenance on the batter y while smoking or in the vicinity of open flames or sparks. This can cause the battery to explode and cause serious injur ies.
12 – English PRESENT A TION Presentation Cong ratulations on y our choice of an e xcellent quality product that will give y ou great pleasure for man y years . This operator’ s manual describes Rider 318 and Rider 320 A WD . Rider 320 A WD is equipped with all wheel dr ive .
English – 13 PRESENT A TION Seat The seat has a jointed attachment on the front edge and can be tipped f orward. The seat can also be adjusted lengthwa ys. Loosen the handles under the seat and adjust it f orwards or backw ards to the desired position.
14 – English Driving Bef ore star ting • Read the saf ety instructions and information concer ning the placement of controls and functions bef ore star ting. • P erform daily maintenance before starting as set out in the Maintenance schedule. • Localise and mark stones and other fixed objects to a void collision.
English – 15 Driving Starting the engine with a weak battery If the batter y is too weak to star t the engine, it should be recharged. When jump leads are used f or emergency star ting, follo w the .
16 – English Maintenance Maintenance sc hedule The f ollowing is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised ser vice workshop. 1) First change after 8 hours.
English – 17 Maintenance Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings bef ore they dr y . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin la yer . Rinse at normal water pressure.
18 – English Maintenance 3 If necessar y , the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar . Do not ov er tighten the cables; they should only be drawn in tow ards the steering collar . 4 Unscrew the belt shields and the side protectors .
English – 19 Maintenance 3 Pull back the throttle to the full throttle position and chec k that the choke is no longer actuated. Replacement of fuel filter Replace the fuel filter e very 100 running hours (once per season) or more frequently if it is clogged.
20 – English Maintenance Ignition system The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. F or recommended spark plug, see T echnical data. Replacing the spark plug 1 Remov e the ignition cable shoe and clean around the spark plug.
English – 21 Maintenance Fitting the cutting head 1 Place the Rider on a flat surf ace and apply the parking brak e. 2 Check that the le ver f or setting the cutting height is in the lowest position and that the lifting le ver f or the cutting unit is in mowing position.
22 – English Maintenance Remo ving the cutting unit 1 Carr y out points 1-6 to put the cutting unit in the ser vice position, see Ser vice position f or the cutting unit.
English – 23 Maintenance 5 Tighten the nuts after adjustment. 6 On completion of the adjustment the unit’ s parallelism should be re-check ed. 7 Screw on the belt shield. 8 Fit the right-hand fender and the front hood. Replacing the cutting unit belts On these cutting units with collision-proof blades , the blades are driven b y one V -belt.
24 – English Maintenance Service position for the cutting unit The cutting head can be placed in the service position to provide easy access f or cleaning, repairs and ser vicing. In the ser vice position the cutting unit is raised and loc ked in the vertical position.
English – 25 Maintenance Chec king the blades T o achiev e the best mowing results it is important that the blades are undamaged and w ell-shar pened. Check that the b lades’ attachment screws are tight. The blades should be balanced after sharpening.
26 – English Lubrication Chec king the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off. Do not check the oil with the engine running. Open the engine cov er . Loosen the dipstick, pull it up and wipe it off .
English – 27 Lubrication Chec king the transmission oil level 1 Remov e the transmission co ver . Undo the two screws (one on each side) and lift off the transmission cov er . 2 Check that there is oil in the tr ansmission’ s oil tank. Rider 318 Fill if necessary with engine oil SAE 10W/40 (class SF–CC).
28 – English T roub leshooting schedule Prob lem Cause Engine does not start There is no fuel in the fuel tank F aulty spar k plug. Def ective ignition cab le.
English – 29 Storage Winter stora ge At the end of the season, or if the machine is going to stand idle f or more than 30 days , it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can b lock the carburettor and interf ere with the engine.
30 – English TECHNICAL D A T A Note 1: The power r ating of the engine indicated is the av erage net output (at specified rpm) of a typical production engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may diff er from this value.
English – 31 TECHNICAL D A T A EC Dec laration of Conf ormity (Applies to Eur ope only) Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel.: +46-36-146500, hereby declares that Husqv ar na Rider 318 a.
´®z+X§T¶6X¨ 2014-06-16 ´®z+X§T¶6X¨ 1156985-26 Original instructions.
Ein wichtiger Punkt beim Kauf des Geräts Husqvarna Rider 318 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Husqvarna Rider 318 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Husqvarna Rider 318 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Husqvarna Rider 318 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Husqvarna Rider 318 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Husqvarna Rider 318 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Husqvarna Rider 318 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Husqvarna Rider 318. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Husqvarna Rider 318 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
