Benutzeranleitung / Produktwartung LTH1438 des Produzenten Husqvarna
Zur Seite of 49
L TH1438 Owner's Manual / 96043006900 / California / 2008-12.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 PRODUCT SPECIFICA TIONS Gasoline Capacity 1.5 Gallons and T ype: Unleaded Regular Oil T ype (API-SG-SL): SAE 10W30 (above 32°F) SAE 5W -30 (below 32°F) Oil Capacity: W/Filter: 56 oz. W/O Filter: 48 oz. Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: 0 - 5.
5 UNAS SEMBLED P ARTS Steering Wheel Steering Wheel (1) W asher Seat (1) Seat Steering Boot Steering Extension Shaft Steering Wheel Adapter Keys (2) K eys Slope Sheet (1) Oil Drain T ube F or Future U.
6 AS SEMBL Y TO REMOVE TRACTOR FROM CAR TON UNP ACK CARTON • Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.
7 Fig. 4 NOTE: Y ou may now roll your tractor off the skid. Follow the ap pro pri ate instruction below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al.
8 CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly leveled.
9 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only.
10 OPERA TION KNOW Y OUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
11 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any adjustments or repairs. W e rec om mend a wide vision safety mask over spectacles or stan dard safety glasses.
12 OPERA TION Fig. 11 Fig. 10 Fig. 12 Fig. 13 J TO ADJUST MOWER CUTTING HEIGHT (See Fig. 11) The position of the attachment lift lever (A) determines the cutting height. A • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4".
13 OPERA TION TO TRANSPORT (See Figs. 15) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po si tion.
14 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time.
15 MOWING TIPS • Mower should be properly leveled for best mowing per for mance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
16 02956 MAINTENANCE LUBRICA TION CHART c SPINDLE ZERK c FRONT WHEEL BEARING ZERK c GENERAL PURPOSE GREASE d REFER TO MAINTENANCE “ENGINE” SECTION IMPORT ANT : DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HA VE SPECIAL NYLON BEARINGS.
17 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed.
18 Fig. 20 Fig. 19 TO CHANGE ENGINE OIL (See Figs. 19 and 20) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm.
19 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
20 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SE RI OUS IN JU RY , BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position.
21 SERVICE AND ADJUSTMENTS E F C G Q R D K G P B L M A IMPORT ANT : CHECK BEL T FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES. • Raise attachment lift lever to highest position. • If necessary , adjust gauge wheels before op er at ing mower as shown in the Operation section of this manual.
22 SERVICE AND ADJUSTMENTS • If adjustment is necessary , see step in Visual Adjust- ment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT -TO-BACK ADJUSTMENT (See Figs. 31 & 32) IMPORT ANT : Deck must be level side-to-side.
23 Fig. 34 SERVICE AND ADJUSTMENTS TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 33) The mower blade drive belt may be replaced without tools. P ark the tractor on level surface. Engage parking brake. BEL T REMOV AL - • Remove mower from tractor (See “TO REMOVE MOW ER” in this section of manual).
24 TO REMOVE WHEEL FOR REP AIRS (See Fig. 37) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). Fig. 37 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER SERVICE AND ADJUSTMENTS Fig.
25 Fig. 38 SERVICE AND ADJUSTMENTS TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 38) WARNING: Lead-acid batteries gen er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries.
26 Fig. 40 SERVICE AND ADJUSTMENTS TRANSMIS SION REMOVAL/RE PL ACE MENT Should your transmission require removal for service or re place ment, it should be purged after reinstallation and before operating the tractor . See “PURGE TRANS MIS SION” in the Operation section of this manual.
27 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
28 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
29 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section.
31 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 SCHEMA TIC M FUSE ST ARTER SOLENOID BA TTERY CLUTCH/BRAKE (PEDAL UP) REVERSE SWITCH (NOT IN REVERSE) SEA T SWITCH (NOT OCC.
32 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 ELECTRICAL 30 33 34 22 79 21 41 42 26 43 27 40 71 16 87 25 T02S 90 28 55 With 12V Outlet Option 59 103 With Service Minder.
33 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 19 32-28 .
34 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 CHASSIS 68 68 68 68 183 183 236 236 34 235 235 137 177 175 130 151 234 214 234 205 202 25 203 206 14 297 191 204 15 130 13.
35 3 532 40 50-12 Logo 5 532 40 75-92 Dash 14 532 41 10-73 Hood 15 532 41 10-79 Lens LH 18 532 40 66-67 Grille/Lens Asm. 25 532 41 10-78 Lens RH 34 532 19 61-25 Plate Engine 36 817 06 05-12 Screw 5/16.
36 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 DRIVE 70 74 56 185 185 51 190 231 170 165 161 166 2 183 205 205 37 33 drive-tex_T2_fender_11_r1 1 2 99 153 279 153 184 221.
37 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 DRIVE KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.
38 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 ENGINE 21 20 OPTIONAL EQUIPMENT Spark Arrester 29 ENGINETEX?"3? 12 42 85 9 84 45 1 81 82 69 2 79 37 2.
39 KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 1 - - - - - - Engine Briggs Model No.
40 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 STEERING ASSEMBL Y 5 62 35 19 60 59 70 68 69 15 14 61 steering-tex_special_11_r1 16 28 28 13 22 64 71 21 45 33 72 4 15 14 .
41 KEY P ART NO . NO. DESCRIPTION 1 532 42 34-69 Wheel, Steering 2 532 19 59-68 Axle Asm., Front 4 532 40 30-87 Spindle Asm., LH 5 532 40 30-88 Spindle Asm.
30 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO. DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO .
42 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 MOWER DECK 1 144 145 40 19 19 6 6 30 38 189 34 189 188 21 69 21 21 30 38 30 188 43 42 60 63 46 147 55 64 34 56 57 59 40 14.
43 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 MOWER DECK KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 41 14-83 Mower Housing 6 532 19 51-86 Arm Suspension 7 532 41 63-58 Screw #10 x 0.
44 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 SEA T ASSEMBL Y 1 532 19 75-18 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock w/Ins.
45 TRACTOR - - MODEL NUMBER L TH1438 (96043006900), PRODUCT NO . 960 43 00-69 MOWER LIFT 2 532 19 52-23 Shaft Asm., Lift 3 532 19 52-31 Lever Asm., Lift RH 7 532 41 15-55 Grip, Lever 10 532 19 63-14 S.
46 SERVICE NOTES.
SECTION 1: LIMITED WARRANTY Husqvarna Professional Products, Inc (“Husqvarna”) warrants the original purchaser the Husqvarna branded product to which this warranty apply (the “Product”) that t.
† Refer to Section 3 for items not covered by this warranty *All consumer product use must have been limited to the owner s residence. Warranted for noncommercial, nonprofessional, noninstitutional and nonincome producing use.
532 42 58-37 12.19.08 TH Printed in the U.S.A..
Ein wichtiger Punkt beim Kauf des Geräts Husqvarna LTH1438 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Husqvarna LTH1438 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Husqvarna LTH1438 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Husqvarna LTH1438 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Husqvarna LTH1438 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Husqvarna LTH1438 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Husqvarna LTH1438 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Husqvarna LTH1438. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Husqvarna LTH1438 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
