Benutzeranleitung / Produktwartung 968999107 / W3213A des Produzenten Husqvarna
Zur Seite of 35
MANUAL NO. 539105471 REV . 01(03/14/02) Adjustment s manual for: Gear Drive, ETS Gear Drive, W alk Hydro, ETS W alk Hydro, Mini Rider , Large Rider Gen 2.
2 MODELS / I.D. : 968999101 / W3212A 968999107 / W3213A 968999102 / W3612A 968999108 / W3613A 968999103 / W3614A 968999104 / W4814A 9689991 10 / W4815A Adjustment Instructions for: Gear Drive Intermed.
3 ADJUSTMENTS FOR ADJUSTMENTS FOR ADJUSTMENTS FOR ADJUSTMENTS FOR ADJUSTMENTS FOR HUSQVARNA 32", 36" AND 48" COMMERCIAL MOWERS HUSQVARNA 32", 36" AND 48" COMMERCIAL MOWER.
4 AXLE ADJUSTMENT BOLTS POSITION A POSITION B POSITION C POSITION D AXLE PIVOT BOLTS PLACE JACK HERE Figure 1 REAR AXLE HEIGHT ADJUSTMENT REAR AXLE HEIGHT ADJUSTMENT REAR AXLE HEIGHT ADJUSTMENT REAR A.
5 BLADE DRIVE BELT ADJUSTMENTS BLADE DRIVE BELT ADJUSTMENTS BLADE DRIVE BELT ADJUSTMENTS BLADE DRIVE BELT ADJUSTMENTS BLADE DRIVE BELT ADJUSTMENTS WARNING WARNING WARNING WARNING WARNING BEFORE PERFOR.
6 SETUP AND ADJUSTMENTS FOR SETUP AND ADJUSTMENTS FOR SETUP AND ADJUSTMENTS FOR SETUP AND ADJUSTMENTS FOR SETUP AND ADJUSTMENTS FOR HUSQVARNA 32", 36" AND 48" COMMERCIAL MOWERS HUSQVARN.
7 SETUP AND ADJUSTMENTS FOR SETUP AND ADJUSTMENTS FOR SETUP AND ADJUSTMENTS FOR SETUP AND ADJUSTMENTS FOR SETUP AND ADJUSTMENTS FOR HUSQVARNA 32", 36" AND 48" COMMERCIAL MOWERS HUSQVARN.
8 Models: 9689991 17 / W3613ETS 968999120 / W4815ETS ETS Gear Drive Intermediate W alk Behind.
9 MAINTENANCE 1. Keep all nuts, bolts, and screws tight to keep mower in safe operating condition. 2. Never store the mower with gas in the tank inside a building where fumes can reach an open flame or spark. Allow engine to cool before storing in an enclosure.
10 Setup & Adjustment s GAS LINE INST ALLA TION 1. The gas line is factory installed on the engine. Attach loose end to fuel tank hose barb and secure with hose clamp. POSITIONING FRONT CASTER SP ACERS 1. Using the cutting height chart, find the correct number of spacers to be placed under the caster swivel.
11 AXLE ADJUSTMENT BOL TS POSITION A POSITION B POSITION C POSITION D PLACE JACK HERE Figure 1 REAR AXLE HEIGHT ADJUSTMENT LOOSEN BOL TS EACH SIDE CASTER SWIVEL 1/2" SP ACERS MACHINERY BUSHING CA.
12 CUTTING HEIGHT ADJUSTMENT CHART AXLE POSITION NUMBER OF SP ACERS BELOW CASTER ARM NUMBER OF 1/4" BLADE SP ACERS UNDER CUTTER HOUSING CUTTING HEIGHT (IN INCHES) 1 1/2 1 3/4 2 2 1/4 2 1/2 1 3/4 .
13 BRAKE / TRACTION ADJUSMENT 1. Disconnect the brake linkage from the brake band arm. 2.With the mower in gear , place the drive levers in the drive position. Firmly pull back on the handles until the tires slide to seat the drive belts into the pulleys.
14 AUXILIAR Y BLADE DRIVE BEL T (48" MODELS ONL Y) T o adjust tension of the auxiliary belt rotate nut on linkage that is attached to deck strap located on the right side of cutter deck.
15 Figure 6 AUXILAR Y BEL T ADJUSTMENT ROD IDLER PIVOT POINT TURNBUCKLE ENGAGEMENT IDLER ASSEMBL Y 1/4" BEFORE OPERA TING Be thoroughly familiar with all controls and how to use them before operating the mower . Know beforehand how to stop the engine, drive wheels, and mower blades in preparation for possible emergency .
16 Adjustment Instructions for: MODELS / I.D. : 968999105 / WH3614A 9689991 1 1 / WH3615A 968999106 / WH4817A CUTTING HEIGHT 1. Before changing cutting heights make sure the blades are off, key switch is off, and remove spark plug wire or wires. 2. Cutting height ranges from 1 1/2” to 5” in 1/4” increments.
17 d. Reinstall the bottom two bolts on both sides.(A tapered punch may be needed to help align the holes.) e. Retighten all four bolts both sides and remove jack. 5. Using the chart(on page 7), find the correct number of spacers to be placed under the caster swivel.
18 CUTTING HEIGHT ADJUSTMENT CHART Note: To quickly achieve small changes in cutting heights, move the spacers from under the cutter housing to above the cutter pulley.
19 Figure 4 (Right side cut away view of console.) Figure 3 REVERSE SPRING DETENT ADJUSTMENT 1. T o check if your reverse spring detent adjustment is set right. Make sure your ground speed lever is pulled back to the neutral position. Release the thumb latches (both sides) and pull up on the control levers at the same time.
20 Figure 5 AUXILARY BELT ADJUSTMENT ROD IDLER PIVOT POINT TURNBUCKLE ENGAGEMENT IDLER ASSEMBLY 1/4" BLADE DRIVE BEL T ADJUSTMENT 1. Before performing adjustments on blade belt, turn the mower off and disconnect spark plug wire or wires. 2. Remove front deck belt shield.
21 ENGINE BEL T GUIDES 1. Before performing adjustments on belt guides, turn the mower off and disconnect spark plug wire or wires. 2. Belt guides under the engine should be adjusted as shown in figure 6. Figure 6 PUMP BEL T 1. Before performing adjustments on pump belt, turn the mower off and disconnect spark plug wire or wires.
22 Models: 968999127 / WHF4215ETS 968999129 / WHF4818ETS 968999130 / WHF5218ETS ETS Hydro Intermediate W alk Behind.
23 CUTTING HEIGHT : 1. S top the mower and disengage the blades. 2. Raise the deck height lever to the transport position. 3. Remove the height adjustment pin and place it in the desired cutting height hole. Move deck height lever down onto the pin and mow .
24 ADJUSTMENTS FRONT DECK BEL T ROUTING: PUMP BEL T 1. Before performing adjustments on pump belt, turn the mower off and disconnect spark plug wire or wires. 2. Check tension on the belt. If it feels loose adjustment will need to be made. 3. Loosen the nut on the bottom of the idler pulley .
25 Mid Mount Zero T urn Riders 42” & 48” 968999157 / ZTHKH4818A 968999158 / ZTHKH4820A 968999167 / ZTHKW4218A 968999168 / ZTHKW4818A 968999169 / ZTHKW4821A MODEL / I.D. : Setup Instructions for: ADJUSTMENTS P ARK BRAKE: 1. S top engine and remove key .
26 FIGURE 2 CUTTING HEIGHT : 1. S top the mower and disengage the blades. 2. Raise the deck height lever to the transport position. 3. Remove the height adjustment pin and place it in the desired cutting height hole. Move deck height lever down onto the pin and mow .
27 FRONT DECK BEL T ROUTING: (See Fig. 4) THROTTLE LEVER TENSION: 1. S top engine and remove key . 2. If throttle lever becomes loose, tension may be adjusted by tightening the pivot bolt. The pivot bolt holds the throttle arm to the throttle mounting bracket which is located under the console.
28 Figure 5a (Left side cut away view) Figure 5b (Left side cut away view).
29 ADJUSTMENTS MOTION CONTROL LINKAGE ADJUSTMENT : 1. This adjustment must be made with the drive wheels rotating. Raise rear of the unit and block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.
30 Adjustment instructions for: 968999159 / ZTH5221KAA 968999160 / ZTH5223KAA 968999161 / ZTH5223KOA 968999162 / ZTH5223KOLA 968999163 / ZTH5225KOA 968999165 / ZTH6125KOA 968999166 / ZTH6125KAA 968999.
31 Adjustment s Cutting Height S top the mower and disengage the blades. Raise the deck height lever to the transport position. Remove the height adjustment pin and place it in the desired cutting height hole. Lower the lift lever down onto pin. NOTE: Anti-scalp rollers must be in the proper position for maximum deck floatation.
32 Reverse S pring Detent Adjustment S top engine and remove key . Pull the motion control lever back to the reverse position and release the lever . When the lever stops it should be in line with the neutral slot, so you can move the lever into neutral slot with out hitting the side of the console frame.
33 Motion Control Linkage Adjustment This adjustment must be made with the rear wheels rotating. Raise the rear of the ma- chine and block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires. T ilt seat forward and remove the seat rod so the seat may rotate forward onto the frame.
34.
We hope you find the links below useful. For further ga rdening information visit www.GardenResources.c o.uk Blower Vacs Brush cutters Brushcutters Chainsaws Chain saws Cultivators Cylinder lawn mower.
Ein wichtiger Punkt beim Kauf des Geräts Husqvarna 968999107 / W3213A (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Husqvarna 968999107 / W3213A noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Husqvarna 968999107 / W3213A - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Husqvarna 968999107 / W3213A reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Husqvarna 968999107 / W3213A erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Husqvarna 968999107 / W3213A besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Husqvarna 968999107 / W3213A verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Husqvarna 968999107 / W3213A. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Husqvarna 968999107 / W3213A gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
