Benutzeranleitung / Produktwartung 15V2s AWD des Produzenten Husqvarna
Zur Seite of 40
E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 15V2 Rider 15V2 A WD Rider 15V2s A WD Oper ator ′ s manual Please read the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.
2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Service journal Pre-delivery ser vice ..................................................... 3 After the first 8 hours .........
English – 3 Service journal Pre-delivery ser vice 1 1a. Dry-char ged battery (5067888-01): T op up battery with acid and charge for f our hours. 1b. Wet-charged battery (5101385-01): Charge at 3 ampere f or 4 hours. 2 Fit steering wheel, seat and any optional equipment.
4 – English INTR ODUCTION Dear Customer , Thank you f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency e ven in small or confined areas.
English – 5 INTR ODUCTION Good service Husqvarna products are sold all ov er the wor ld and only through servicing dealers. This is to ensure that you, the customer , get the best suppor t and ser vice. F or e xample, bef ore this machine was delivered it w as inspected and adjusted by your dealer .
6 – English KEY T O SYMBOLS Symbols These symbols are on the machine and in the instructions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 7 KEY T O SYMBOLS Brak e Star ting instructions Switch off the engine and take off the ignition cable bef ore repairs or maintenance Check the engine’ s oil le v el Check tr ansmission o.
8 – English SAFETY INSTR UCTIONS Safety instructions These instructions are for y our saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage for y our new Rider .
English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hearing protection to minimise the r isk of hearing impairment.
10 – English SAFETY INSTR UCTIONS • Do not tr y to stabilize the machine b y putting your foot on the ground. • When cleaning the chassis, the machine ma y nev er be driven near v erges or ditches. • F ollow the manuf acturer’ s recommendations regarding wheel weights or counterbalance weights to increase machine stability .
English – 11 SAFETY INSTR UCTIONS • Be especially careful when handling batter y acid. Acid on the skin can cause serious corrosive injuries. In the e v ent of spillage on the skin wash immediately with w ater . • Acid in the ey es can cause blindness, contact a doctor immediately .
12 – English WHA T IS WHA T? Location of the contr ols 1 Choke control 2 Switch f or the lights 3 Throttle control 4 Ignition lock 5 Counter 6 Cutting height adjustment le ver 7 Lifting le ver f or .
English – 13 PRESENT A TION Presentation Congratulations on y our choice of an excellent quality product that will give y ou great pleasure for man y years . This operator’ s manual describes Rider 15V2, Rider 15V2s A WD and Rider 15V2 A WD . The machines are equipped with a 15 horse power engine from Kaw asaki.
14 – English PRESENT A TION Cutting unit Rider 15V2, Rider 15V2s A WD and 15V2 A WD can be equipped with two diff erent cutting units. • Combi 1030mm/41” • Combi 1120 mm/44” The Combi-unit, equipped with a BioClip-plug, finely chops the cuttings to f er tiliser .
English – 15 PRESENT A TION The seat can also be adjusted lengthwa ys. T o adjust move the le ver under the front edge of the seat to the left, so that the seat can be mov ed forward or bac kwards to the required position. Fuelling The engine runs on unleaded petrol with a minimum octane rating of 87 (not mix ed with oil).
16 – English Driving Bef ore star ting • Read the saf ety instructions and information concer ning the placement of controls and functions bef ore star ting. • P erform daily maintenance before starting as set out in the Maintenance schedule. Star t the engine 1 Make sure that the clutch control is depressed.
English – 17 Driving 8 Let the engine run at moderate speed or half throttle for 3- 5 minutes bef ore subjecting it to heavy load. 9 Set the required engine speed with the throttle control. Star ting the engine with a weak battery If the batter y is too weak to start the engine, it should be recharged.
18 – English Driving 4 Press in the lock b utton on the lifting lev er and lower the cutting unit. Cutting tips • Localise and mark stones and other fixed objects to a v oid collision. • Star t with a high cutting height and reduce down until the required mowing results are obtained.
English – 19 Maintenance Maintenance schedule The f ollowing is a list of the maintenance which should be conducted on the machine . For those points not described in this man ual, visit an authorised ser vice workshop. 1) If the machine is used daily it should be lubricated twice a week.
20 – English Maintenance Cleaning Clean the machine directly after use. It is much easier to w ash off grass cuttings bef ore they dry . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin layer . Rinse at normal water pressure.
English – 21 Maintenance 1 Remov e the frame plate by loosening the screws (2) and lift the frame plate b y the rear edge. 2 Check the tension of the steering wires by squeezing them together by the arro ws as illustrated.
22 – English Maintenance If adjustment is necessar y , adjust the lower wire as f ollows: 1 Loosen the clamping screw f or the cable’ s outer casing and mov e the throttle to the full throttle position. 2 Check that the throttle wire is attached to the correct hole in the lower le ver , see diagram.
English – 23 Maintenance 5 T ap the paper filter against a hard surface to shak e off the dust. 6 If the paper filter is still dir ty it should be replaced with a new one . Alwa ys replace the paper filter ev ery 200 hours. 7 Put the pre-filter and paper filter back into the air filter unit.
24 – English Maintenance Chec k the safety system The machine is equipped with a saf ety system that pre vents star ting or driving under the following conditions . The engine should only be possible to start when the cutting unit is in its raised position and the h ydrostat pedals are in the neutral position.
English – 25 Maintenance Replacing the light b ulbs F or inf ormation about the bulb type, see T echnical Data. 1 Loosen the lock n ut and remov e the Allen bolt. Remov e the steering wheel. 2 Unscrew the tw o screws holding the co v er on the power ser v o housing.
26 – English Maintenance Chec king the tyre pressure The tyre pressure should be 60 kP a (0.6 kp/cm 2 /8.5 PSI) all round. T o improve driving the pressure on the rear tyres can be reduced to 40 kP a (0.4 kp/cm 2 /5.6 PSI). The maximum tyre pressure is 100 kP a (1,0 kp/cm 2 /14 PSI).
English – 27 Maintenance 6 Press down the frame and remo ve the pin. 7 Slide the unit in and inser t the pin. Make sure that the tongue (3) on the cutting unit engages correctly . 8 Fit the drive belt around the drive wheels of the cutting unit. 9 Hook up the height adjustment strut.
28 – English Maintenance 4 Place a set of bathroom scales under the cutting unit’ s frame (front edge) so that it rests on the scales. If necessar y a bloc k can be placed between the frame and scales so that the suppor t wheels do not bear any weight.
English – 29 Maintenance Service position for the cutting unit The cutting head can be placed in the ser vice position to provide easy access f or cleaning, repairs and ser vicing. In the ser vice position the cutting unit is raised and loc ked in the vertical position.
30 – English Maintenance 8 Lift of the drive belt. Then pull out the pin. 9 Pull the frame f orwards and refit the pin. 10 Grasp the front edge of the cutting unit, pull out and raise into the ser vice position. If the cylindrical bolt, which is now holding the cutting unit is remov ed, the cutting unit can be lifted off.
English – 31 Lubrication Chec king the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off . Open the engine cov er. Loosen the dipstick, pull it up and wipe it off . Now insert the dipstick again, without tightening it.
32 – English Lubrication Fill with new oil according to Chec king the engine’s oil le vel. Star t the engine and let it idle for about 3 min utes. No w stop it and check f or signs of leakage. Fill with oil to compensate f or the oil held in the new oil filter .
English – 33 T roub leshooting schedule Prob lem Procedure Engine does not star t There is no fuel in the fuel tank Spark plug defectiv e F aulty spar k plug connections or interchanged cables Dir t.
34 – English Storage Winter storage At the end of the season, or if the machine is going to stand idle f or more than 30 da ys, it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can bloc k the carburettor and interf ere with the engine.
English – 35 T echnical data 1) As rated b y the engine manuf acturer Dimensions Rider 15V2 Rider 15V2 A WD Rider 15V2s A WD Length without cutting unit, mm/ft 2020/6,61 2020/6,61 2020/6,61 Width wi.
36 – English T echnical data EC-dec laration of conf ormity (Applies to Eur ope only) Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel.: +46-36-146500, hereby declares that Husqvarna Rider 15V2, Rid.
.
´®z+S!r¶6H¨ ´®z+S!r¶6H¨.
.
´®z+S!r¶6H¨ 2008-10-21 ´®z+S!r¶6H¨ 1151018-26.
Ein wichtiger Punkt beim Kauf des Geräts Husqvarna 15V2s AWD (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Husqvarna 15V2s AWD noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Husqvarna 15V2s AWD - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Husqvarna 15V2s AWD reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Husqvarna 15V2s AWD erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Husqvarna 15V2s AWD besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Husqvarna 15V2s AWD verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Husqvarna 15V2s AWD. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Husqvarna 15V2s AWD gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
