Benutzeranleitung / Produktwartung 600 des Produzenten Huffy
Zur Seite of 26
1 02/05 P/N 211636 10 © COPYRIGHT 2005 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 P/N 211636 10 02/05 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates.
02/05 P/N 211636 10 3 W ARNING F AILURE T O FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or an y par t of the system including bac kboard, support braces or net.
4 P/N 211636 10 02/05 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
02/05 P/N 211636 10 5 For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside.
6 P/N 211636 10 02/05 Get to know the basic parts of your basketball system..... FRONT P ANEL BACKBOARD FRONT RIM BASE POLE.
02/05 P/N 211636 10 7 P ARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 200503 Cover, Black OR 1 200504 Cover, Red 2 1 806620 Base Assembly 3 1 804833 Exacta Height Assembly 4.
8 P/N 211636 10 02/05 HARDW ARE IDENTIFIER (BOL TS & SCREWS) * You may have extra parts with this model. Item #7 (2) Item #40 (1) Item #39 (2) Item #23 (1) Item #29 (6) Item #16 (2) Item #12 (1) I.
02/05 P/N 211636 10 9 HARDW ARE IDENTIFIER (STEEL SP ACERS) HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS CAPS & CLIPS) Item #28 (2) Item #21 (2) Item #13 (2) I.
10 P/N 211636 10 02/05 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE And/Or: This is what your system will look like when you’ve finis.
02/05 P/N 211636 10 11 1A. Check the following pre-assembled base areas for tightness: Eye bolt s P/N 203452, W asher P/N 203218 , Nut P/N 203100, Carriage Bolts P/N 203223 .
12 P/N 211636 10 02/05 Check the following pre-assembled handle areas for tightness: Screw P/N 204803, Nut P/N 203100, Carriage Bolt s P/N 203103 . Carriage Bolt P/N 203103 Nut P/N 203100 Nut P/N 2031.
02/05 P/N 211636 10 13 6 5 4 3. WOOD SCRAP (NOT SUPPLIED) 5 4 While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole.
14 P/N 211636 10 02/05 4. 4 5 6 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE TROUGH Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown. IMPORT ANT!: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP.
02/05 P/N 211636 10 15 9 7 6 9 7 13 8 47 5. Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut should be tightened until flush (even) with locknuts outer edge. 12 10 6 7. Secure cover to rod (9) using washers (47) nuts (8) and nut covers (13) as shown.
16 P/N 211636 10 02/05 8 . Install pole mount bracket (15) and reinforcement bracket (49) with carriage bolt s (16) as shown. T ighten flange nuts (14) completely . 4 49 14 14 15 16 16 9. Attach sp acers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), and nuts (18) as shown.
02/05 P/N 211636 10 17 Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. 10 . 15 14 24 22 22 25 23 FIG . A 25 24 Loop end of pin lanyard (25) over carriage bolt (23) as it p asses through the pole mount bracket (15) during this assembly .
18 P/N 211636 10 02/05 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION B: A TT ACH THE BACKBOARD Phillip s- Head Screwdriver This is what your system will look.
02/05 P/N 211636 10 19 Assemble backboard brackets (27) using sp acers (28), bolts (19), and nut s (18) as shown. 1. 28 28 19 19 18 18 27.
20 P/N 211636 10 02/05 2. 3. Install cover (1) over spring return mechanism as shown. 29 26 26 27 31 Refer T o Instructions Included With Rim Hardware For Rim Assembly . 48 11 47 32 34 1 39 Attach lower elevator tubes (32) and counter balance springs (33) to backboard support brackets (27) using sp acers (26), bolt (29), and nut (31) as shown.
02/05 P/N 211636 10 21 4. Attach upper elevator tubes (35) to backboard support bracket s (27) using spacers (26 & 1 1), bolt (29), and nut (31) as shown.
22 P/N 211636 10 02/05 5. Install net clip s. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
02/05 P/N 211636 10 23 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 6.
24 P/N 211636 10 02/05 31 31 40 38 32 4 37 37 29 30 32 30 29 32 29 35 30 31 31 35 30 37 36 36 7. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (38). Use caution; elevator assembly is heavy . 8. Install upper elevator tubes (35) to triangle plates (37) as shown.
02/05 P/N 211636 10 25 9. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 10. Roll completed assembly to desired position.
26 P/N 211636 10 02/05 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height.
Ein wichtiger Punkt beim Kauf des Geräts Huffy 600 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Huffy 600 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Huffy 600 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Huffy 600 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Huffy 600 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Huffy 600 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Huffy 600 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Huffy 600. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Huffy 600 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
