Benutzeranleitung / Produktwartung QS Quiet des Produzenten Hoover
Zur Seite of 20
.
Fill in and retain! The HOOVER vacuum cleaner you have just purchased is a com- bination cleaner. It has a motorized power nozzle for carpet and floor cleaning and has cleaning tools for above the floor cleaning.
l Read all instructions. l Warning: Electric shock could occur if used outdoors or on wet surfaces. l Close supervision is necessary when any appliance is used by or near children. Do not allow vacuum cleaner to be used as a toy or to run unattended at any time.
UNPACKING Unpack the cleaner from the carton and identify the parts shown. Remove and dispose of the cardboard packing. A. Canister cleaner B. Power nozzle C. Throw away bag D. Extension wands, cleaning tools and hose D The cleaner assembled will look like the drawing below.
1. 2. 3. Wall Floor Brush 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Power Nozzle automatically adjusts to different carpet pile heights. Casters provide easy towing; pull cleaner using hose to guide the cleaner over carpet, area rugs and door sills. Hose Cord Connection to Cleaner is made by plugging hose cord into cleaner base at receptacle.
How to assemble 1. Connect hose To connect hose, insert hose into opening of cleaner lining up the ar- row on the hose with the dot on the cleaner. Turn the hose clock- wise until it lines up with the bar on the cleaner and latch locks into place. When the hose is attached proper- ly, the hose cord plug will reach to the receptacle on the cleaner.
Attach the curved wand to the straight wand. Position cord into cord clips on extension wands, placing excess cord between noz- zle and bottom cord clip. To attach the hose to the exten- sion wands, rotate the plastic latch ring on the handle to accept the button projection on the curv- ed wand.
How to use Handle adjustments The handle has two positions when used with the power noz- zle: Upright and Operating. To lower handle to the Operating position, place your foot on the power nozzle and push the han- dle down.
Nozzle connector Removing larger items from carpet and floor surfaces before vacuuming will help maintain the cleaning effectiveness of your cleaner. However, if loss of suction power should occur, pr.
To connect and remove tools To connect the tools, insert end of tool into the extension wand and snap into position. To disconnect, press down on the center of the spring latch and remove tool. Tools may also be attached to the handle by rotating the plastic latch ring to accept the button projec- tion on the tool.
To clean stairs Clean stairs by placing the cleaner on its side as pictured in the il- lustration. Clean stairs from bot- tom to top. How to store Cord wrap When cleaner is not in use, wrap the cord around the cord storage hook, located on the cover of the cleaner, and the carrying handle.
Maintenance The following sections are concerned with proper maintence of the clean- er. Familiarize yourself with these home maintenance tasks and keep this owner’s manual in a convenient place where you can refer to it when need- ed. Proper use and care of your cleaner will insure continued cleaning ef- fectiveness.
Push used bag awayfrom holder and lift out. Grasp edges of collar section and push opening of collar section of new bag onto holder. Make sure collar is pushed completely up to the ridge on the holder. Adjust bag around the motor housing and open the folds of the bag to allow the bag to properly fill.
SECONDARY FILTER To clean secondary filter Disconnect cleaner from elec- trical outlet. The secondary filter protects the motor from dirt particles. If the fil- ter becomes dirty, either clean or replace it. To remove secondary filter, open cover of cleaner and lift the filter from the top of the motor housing.
Return nozzle to original position and lift up back of nozzle cover. Then remove cover, rotating it for- ward and lifting it off. To remove the agitator, position your hand underneath the nozzle base at the agitator opening and push up the belt side of the agita- tor.
Slide belt side of agitator into place, pushing the agitator slightly to left, pulling it forward and then down. Roll agitator to make sure belt is positioned properly. The cover attaches at the front of the nozzle. Place the notched edge at the front of the cover into the groove in the nozzle base.
AGITATOR BRUSHES When to replace brushes To check condition of brushes, place edge of a card on the bot- tom of nozzle base, across agita- tor opening. Rotate agitator by hand. If brushes do not touch edge of card, all four brushes and brush roll should be replaced to maintain cleaning effectiveness.
3. Note position of bar-brush as- . semblies to insure correct replace- 1 / ment. / Remove bar-brush assemblies by pulling them from agitator slots. Use pliers if necessary. The word “BAR” is stamped near the slots on the agitator. Match the bar side of the bar brush assembly with the label on the agitator shell.
1 lJ ser check list I This appliance was inspected thoroughly and was in good operating condi- tion when it was shipped from the factory. If a minor problem develops, it usually can be remedied quite easily when the cause is identified. Accord- ingly, this check list is provided for your convenience.
VCMA VACUUM CLEANER MANUFACTURERS ASSOCIATION (HOOVER - AN ASSOCIATION MEMBER) Service To The Consumer Since 19 13 This information has been compiled by the Vacuum Cleaner Manufacturers Associ- ation from Governmental and Private Sources concerned with product safety.
Ein wichtiger Punkt beim Kauf des Geräts Hoover QS Quiet (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hoover QS Quiet noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hoover QS Quiet - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hoover QS Quiet reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hoover QS Quiet erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hoover QS Quiet besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hoover QS Quiet verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hoover QS Quiet. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hoover QS Quiet gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
