Benutzeranleitung / Produktwartung HD4U des Produzenten Honeywell
Zur Seite of 32
Document 800-00031 – Rev A – 04/08 Day/Night Ultra Wide Dynamic Fixed Dome Camera User Guide NTSC / P AL HD4U HD4UX.
2 Revisions Issue Date Revisions A 04/08 New document..
Document 800-00031 Rev A 3 04/08 Wa r n i n g s Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty.
4 FCC Compliance Statement Information to the User : This equipment has been tested and found to comply with the limits for a Class B digital de vice. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful in terference in a residential installation.
Document 800-00031 Rev A 5 04/08 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Introduction The unobtrusive, low-profile design of the HD 4U/X CCTV Camera is ideal for indoor and outdoor installations in comm ercial and residential venues. Before Y ou Begin Please read this guide carefully before you install the HD4U/X CCTV Camera.
Document 800-00031 Rev A 7 04/08 Equipment Required You will require the following tools to complete the installation: • Phillips screwdriver • Tools supplied in the hardware kit (three Allen keys.
8 Installation The HD4U/X is weather-sealed for indoor or outd oo r locations. The HD4U/X is a fully-integrated enclosure with camera and lens. The wiring can be completely concealed to reduce the ri sk of tampering.
Document 800-00031 Rev A 9 04/08 Connecting Cables Through the Housing Base For installations that require pulling cables th rough the grommet located in the bottom of the base: 1. Use a sharp knife to cut an ! opening in the base gasket (see Figure 1 ).
10 Connecting Cables Through the Side Conduit 1. Peel back the bottom flat gasket below the si de conduit just enough to expos e the security screw. 2. Use the supplied Allen key to loosen and remove the security screw (see Figure 2 ). 3. Use a flat screwdriver to unscrew the conduit p lug.
Document 800-00031 Rev A 11 04/08 Electrical Box Installations Figure 3 i ll u st r at e s h o w to m ou n t t h e HD 4 U/ X di r ec t l y t o a 4S el e c tr i ca l b ox o r d i re c tl y t o w a ll o r ceiling.
12 Figure 4 illustrates how to mount the HD4U/X directly to a double gang or single gang electrical box. Figure 4 Double Gang/Single Gang Electrica l Box Installation (Single Gang Shown) Electrical bo.
Document 800-00031 Rev A 13 04/08 Connecting the Wiring Follow Figure 5 to connect the video and power wires. Figure 5 Wiring Connec tion Adjusting the Camera To adjust the HD4U/X Camera: 1. Apply 12 VDC or 24 VAC power to the camera and monitor the video signal.
14 Figure 6 Gimbal Adjustment Adjusting the Lens F ocus Lenses are pre-focused at the factory but may require a final adjustment after installation because the optical effect of the dome ma y cause a slight defocusing of the lens. TECH TIP! To check the focus, hold the dome over t he lens while making any adjustments.
Document 800-00031 Rev A 15 04/08 Camera Setup Camera F unctions OSD Menu Structure - Press d own on th e joysti ck and ho ld two sec onds to access the MAIN MENU.
16 Configuring the WDR Presets Select the appropriate camera mode for t he lighting conditions. <CUSTOM> Opens the CUSTOM screen where you can adjust the limits of the wide dy namic range by moving the cursor. Note Watch the changes on the video monitor for the best results.
Document 800-00031 Rev A 17 04/08 Optimizing the Camera Setup Note This menu is for advanced users only. The table below explains the options on the CAMERA S ETUP menu. Each selection on this menu takes you to a separate screen (see description below).
18 >SYNC Synchronize the vertical interval sync puls e of your camera with other equipment to reduce the effect of picture roll on the monitor. Select either: <INTERNAL> (default) for cameras.
Document 800-00031 Rev A 19 04/08 Setting the Camera Image Properties The table below explains the options on the VI EWING menu. <ATW Xtnd> Automatic Tracking White Balance (Extende d Range). Continuously monitors the color temperature while an internal micro controller sets the white balance.
20 >FLIP Select either: <ON> to reverse the image horizon tally on the video monitor , or <OFF> (default) > ID DISPLAY. Select ON to open the CAMERA ID SETUP screen where you can add a CAMERA ID (title) o f up to 8 chara cters. Move the cursor (>) to CAMERA ID , then press down on t he joystick.
Document 800-00031 Rev A 21 04/08 Setting the Day/Night Control The table below explains the options on the DAY/NIGHT SETUP menu. Note This setting is dependent on the AGC setting ( See >AGC on page 18). Note Certain video recorders require color carrier/burst to operate.
22 Restoring Settings On the main MENU , sele ct RESTORE DEFAULTS , then YES followed by ENTER (middle button). This reloads the factory default camera settings.
Document 800-00031 Rev A 23 04/08 Installing the Enclosure Cover To install the enclosure cover , use the Allen key (supplied) to secure the HD4U/X dome enclosure to the base wit h four #8-32 security scre ws. Figure 7 Enclosure Cover Installa tion Routine Maintenance Use regular liquid cleaners to remove dirt and grime from the HD4U/X dome.
24 Solving Common T echnical Issues No Video ❐ ❐ ❐ Check that the power supply voltage is within the operating specificat ions for your camera model. See Specifications for details. Check the video signal connections are correct. Check for a loose connection .
Document 800-00031 Rev A 25 04/08 W arranty and Service Subject to the te rms and conditions listed on the Product warranty, during the warr anty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid.
26 Specifications Video Signal Specifications NTSC PAL Video Standard: 525 lines, 2:1 in terface 625 lines, 2:1 interface Scanning System: Progressive Image Sensor: 1/3 in.
Document 800-00031 Rev A 27 04/08 Temperature: Operating: -13°F to +122°F (-25°C to +50°C) Storage: -4°F to +140°F (-20°C to +60°C) Mechanical Specifications Dimensions (D) x (H): 5.
28 Cable Guidelines Maximum Power Supply Cable Length (feet/met ers) Cameras With AC/DC P ower Supp lies Wire gauge Total load Power supply 24 AWG 22 AWG 18 AWG 16 AWG 3.
Document 800-00031 Rev A 29 04/08 HD4U Mounting T e mplate.
30.
Document 800-00031 Rev A 31 04/08.
© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without wri tten permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects.
Ein wichtiger Punkt beim Kauf des Geräts Honeywell HD4U (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Honeywell HD4U noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Honeywell HD4U - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Honeywell HD4U reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Honeywell HD4U erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Honeywell HD4U besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Honeywell HD4U verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Honeywell HD4U. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Honeywell HD4U gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
