Benutzeranleitung / Produktwartung LX30C ML-104353 des Produzenten Hobart
Zur Seite of 28
N S T R U C T I O N S I LX SERIES DISHWASHER LX SERIES DISHW ASHERS MODELS LX18 ML-104349 LX18C ML-104350 LX18H ML-104351 LX30 ML-104352 LX30C ML-104353 LX30H ML-104354 LX40C ML-104355 LX40H ML-104356 FORM 18615 Rev. I (July 2000) 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.
– 2 – © HOBART CORPORATION, 1993 T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . .
– 3 – Model LX30 Dishwasher Installation, Operation, and Care of LX SERIES DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL The LX Series dishwashers are fully automatic, front-loading dishwashing machines which are equipped with a 3 / 4 horsepower electric motor.
– 4 – INST ALLA TION UNPACKING Immediately after unpacking the dishwasher, check for possible shipping damage. If this machine is found to be damaged, save packaging material and contact the carrier within 15 days of delivery. Prior to installation, verify that the electrical supply agrees with the specifications on the machine data plate.
– 5 – PLUMBING CONNECTIONS WARNING : PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITARY, SAFETY, AND PLUMBING CODES. Drain A drain hose is provided with a 3 / 4 " pipe connection adapter. This should be securely plumbed into the sink drain.
– 6 – ELECTRICAL CONNECTION WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT.
– 7 – Refer to the data plate on the front of the machine and the label inside the control drawer at the power connection for proper selection. Use stranded copper wire only. 1. Remove the cover plate at the upper right in the back of the machine (Fig.
– 8 – DETERGENT AND RINSE AID If manually adding detergent in an LX18, LX18C, or LX18H at the beginning of each cycle, the machine must be programmed to the “True Fill and Dump” mode. This will ensure detergent is not dumped before filling with fresh, hot water.
– 9 – INSTALLATION DIAGRAM (LX18, LX18C & LX18H) — 329300.
– 10 – INSTALLATION DIAGRAM (LX30, LX30C & LX30H) — 329301.
– 11 – INSTALLATION DIAGRAM (LX40C & LX40H) — 329302.
– 12 – OPERA TION CAUTION: Items such as pewter, aluminum, and silver will be attacked by sodium hypochlorite (bleach). Therefore, chemical sanitizing dishwashers should not be used to wash such items.
– 13 – Operating Models LX18, LX18C, LX18H, LX30, LX30C, and LX30H Dishwashers DO THIS DISPLAY SHOWS REMARKS Press ON. Model number. Dishwasher performs self check. This takes 5-10 seconds. FILL lit and sump Dishwasher fills with water. When filled, temperature displayed pump turns on for 10 seconds.
– 14 – DIAGNOSTIC MESSAGES In the event of a problem with a temperature probe, the display will flash "P1," "P2," or "P3" every 10 seconds. The respective heaters will shut down. Other functions will continue to operate normally.
– 15 – MODELS LX30, LX30C and LX30H WASH/RINSE CYCLE TIMES Wash 85 Sec.** Drain* 10 Sec. Max. Dwell 4 Sec. Rinse 10 Sec. Dwell 6 Sec. * Drains off about 1 gallon of water.
– 16 – CONTROLS — Models LX40H & LX40C (Fig. 4) Fig. 4 Operating Models LX40H & LX40C DO THIS DISPLAY SHOWS REMARKS Press ON. Two counts of "00000" to Dishwasher performs self check. This takes "99999", then model 5-10 seconds.
– 17 – Operating Models LX40H & LX40C (Continued) DO THIS DISPLAY SHOWS REMARKS Open door; slide rack of READY. dishes into dishwasher. Close door. Press WASH. WASH lit and sump Machine initiates a wash and rinse cycle. (Before you press WASH, temperature displayed you can change the cycle during wash cycle.
– 18 – DIAGNOSTIC MESSAGES In the event of a problem with a temperature probe, the display will flash PROBE and CALL SERVICE will be lit. The respective heaters will shut down. Other functions will continue to operate normally. Contact your local Hobart Service Office.
– 19 – MANAGER PROGRAMMING (Machine Must Be In READY Mode) To enter the Manager Programming Mode, you must first enter the Operator Programming Mode by pressing and holding "LX40" on the control panel (this is the HIDDEN key), then pressing WASH.
– 20 – PROGRAMMABLE VARIABLES AND RECOMMENDED SETTINGS — MODELS LX40H & LX40C The following functions of the dishwasher are programmable. The chart below shows the variables that may be programmed for each function and the recommended setting for each.
– 21 – Dishes must be scraped and/or rinsed to remove food particles and other debris. Never use steel wool on ware to be loaded into the dishwasher. Place dishes in a rack. Do not stack dishes on top of each other as water must have free access to all sides of every dish.
– 22 – 3. With a damp cloth, wipe the interior of the machine, the water level probes (Fig. 9), and the water level probe under the fine strainer. DO NOT use steel wool. Wipe the exterior of the machine. When cleaning the inside of the door, be sure to wipe the lip at the bottom of the door.
– 23 – MAINTENANCE DELIMING — GENERAL WARNING: DELIMING SOLUTION, RINSE AGENTS, OR ANY OTHER KIND OF ACID MUST NOT COME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONTAINING BLEACH USED IN CHEMICAL SANITIZING MACHINES. MIXING MAY CAUSE HAZARDOUS GAS TO FORM.
– 24 – DELIMING — Models LX30, LX30C & LX30H 1. Remove standpipe assemblies from chemical containers and place them as close to the floor as possible. Place a catch pan under them. 2. Cycle the machine four times to clear the lines of chemicals.
– 25 – DELIMING — Models LX40H and LX40C Models LX40H and LX40C are equipped with an automatic delime cycle reminder. After the preprogrammed number of cycles has expired, the control will indicate the delime request by illuminating DELIME.
– 26 – TROUBLESHOOTING This section outlines various symptoms and possible causes that may be encountered in the event of abnormal machine operation. If symptoms persist after possible causes have been checked, service may be required. SYMPTOM POSSIBLE CAUSES No machine operation 1.
– 27 – SYMPTOM POSSIBLE CAUSES Unexpected results on 1. Etching — usually caused by any combination of high dishes. temperatures, soft water, soft glass, or high alkaline washing solutions. 2. Tarnishing — avoid washing silver, silver plate and pewter in chemical sanitizing machines.
– 28 – SYMPTOM POSSIBLE CAUSES Machine fills too high or 1. Machine not level — see LEVELING in this manual. leaks from door. 2. Fill solenoid valve leaking — turn the dishwasher OFF; if water continues to come in (through the rear fill air gap on LX18 Machine won't drain.
Ein wichtiger Punkt beim Kauf des Geräts Hobart LX30C ML-104353 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hobart LX30C ML-104353 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hobart LX30C ML-104353 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hobart LX30C ML-104353 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hobart LX30C ML-104353 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hobart LX30C ML-104353 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hobart LX30C ML-104353 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hobart LX30C ML-104353. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hobart LX30C ML-104353 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
