Benutzeranleitung / Produktwartung FT1000S des Produzenten Hobart
Zur Seite of 44
701 S. RIDGE A VENUE TROY , OHIO 45374-0001 937 332-3000 www .hobartcorp.com F47505 (October 2014) FT1000-SERIES DISHW ASHERS MODEL ML-130250 COVERS ALL OF THE FOLLOWING MODELS FT1000 FT1000-ER FT1000.
– 2 – © HOBART 2008.
– 3 – T ABLE OF CONTENTS NOTES FOR THE INST ALLERS ................................................... 4 How to Reduce the Clearance Height of the Control Box During Move-In ................ 4 UNP ACKING ...........................................
– 4 – Installation and Care Of FT1000 SERIES DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL NOTES FOR THE INST ALLERS Read the entire manual befor e installing the machine . 1. Do not use a forklift to move or unskid machine sections. 2. Do not throw out any loose parts.
– 5 – 1. Remove the two shipping hinges from the side of the control box by removing the two 5/16-18 bolts from each bracket. 2. While two people are securely supporting the main control box, remove the four 5/16-18 nuts, lock washers, and washers from the inside of the shipping braces behind the control box.
– 6 – UNP ACKING Immediately after unpacking the dishwasher , check for possible shipping damage. If the machine is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery .
– 7 – 7. Remove any packaging, tape, wire and bracing from each section. Remove all rear and lower panels. 8. V erify that shipping tape has been removed from all oats in each tank and that theoatsarefreetooperateproperly .
– 8 – • Continue to level the center section front to back by removing the top panels and placing level across the top of the chambers on both ends of center section (Fig. 3). Fig. 3 ASSEMBL Y Rotating Control Box 90 Degrees The main control box is shipped with the upper and lower shipping hinges connected to the side of the control box.
– 9 – TRIM EXCESS TAPE FROM INSIDE OF CHAMBER FLANGE FOLD FRONT EDGE OF FOAM TAPE 1/2 ” FRONT OF MACHINE Fig. 4 Fig. 5 Fig. 6 Apply foam tape to unload chamber section where the rear perimeter of the control box will be mounted.
– 10 – Attaching Control Box to Unload Section 1. For ease of control box installation, remove the detachable leg section on the front leg of the unload section where the control box will be mounted by removing the upper and lower ¼-20 hardware.
– 1 1 – 8. Remove the two shipping braces from the end of the dual rinse section by removing the three 5/16 bolts and associated hardware from each brace.
– 12 – SECURE VERTICAL FRAME CORNER POSTS AT TWO LOCATIONS Fig. 8 Installing the Curtain Bafes and Unload Air Bafe - T op of Chamber Flanges On prewash/wash section joint, instal.
– 13 – Fig. 9 On dual rinse/unload section joint, install the unload air bafe and two curtain hangers. The curtainhangers mounton tot.
– 14 – CHAMBER FLANGE AND BOL T ASSEMBL Y A T EACH SECTION JOINT Description Qty . Bolt Size Assembly Order Instructions Short Bolt-Use except where long bolts or medium bolts are required 22 ¼-20 x 5/8” [Bolt, W asher] [W asher , Lockwasher , Nut] Use permagum on insides of washers on both sides of chamberanges.
– 15 – PERMAGUM SADDLE JOINT PERMAGUM Fig. 13 Control Box Connections Refer to the electrical diagram stored inside the main control box door . After use, make sure that the diagram is placed inside the control box.
– 16 – Installing the Flowback Pipe (W ash to Prewash T anks) Installtheowbackpipebetweenthewashtankandtheprewashtank(Fig.14). Make sure the owback pipe is adequately lubricated with O-ring lube (not supplied).
– 17 – Relocating Master Drain to Load End (Only Machines Equipped with Auto Clean, Auto Delime, & the ASR Section) NOTE: If the dish machine is equipped with the Auto Clean and Auto Delime features, but does not contain the ASR section, then the Master Drain assembly must remain located at the unload end of the machine.
– 18 – For a R-L machine (steps 9-1 1): 9. Remove pipe (00-948761-00018) connecting the master drain and the nearest drain tee. 00-948761-00018 can be discarded. See Fig. 16. 00-948761-00018 Fig. 16 10. Remove rubber hose connected to drain tee located at load end of the unit.
– 19 – 21. Loosen clamps securing rubber hoses to drain solenoid valve and rotate solenoid valve 180 degrees. Retighten clamps. 22. Attach rubber hoses to plastic drain tee and barbed tting on master drain assembly and tighten clamps.
– 20 – 29. Remove two bolts, nuts, and washers attached to the load support bracket shipped with the machine (00-950109). See Fig. 19. TWO STUDS 00-950109 Bottom View (R-L Machine) Fig. 19 30. Attach load support bracket to load master drain platform using two studs located on the bottom of the load drain platform.
– 21 – DRAIN BACK PAN SLOPES TOWARD PREWASH TANK WASH SECTION LOWER TRACK Fig. 20 Fig. 21 Install the pan between the dual rinse and unload section ensuring that the pan slopes towards the dual rinse tank (Fig.
– 22 – REAR PANEL TOP PANEL FRONT PANEL Fig. 24 2. Install one of the blower assemblies on top of the heater housing by lowering the blower assembly on an angle so that the front tabs hook underneath the notches on the top plate of the heater housing (Fig.
– 23 – 5. Repeat steps 2 thru 4 to install the second blower assembly . 6. Route both blower cables between the blower assemblies and the vertical enclosure panel to the rear of the control box. NOTE: Ensure that the cables are not routed on the side of the blowers where the air intake chamber openings are located.
– 24 – ELECTRICAL CONNECTION(S) Electrical and grounding connections must comply with applicable portions of the National Electrical Code (NFP A No. 70, latest edition) and/or other local electrical codes. Disconnect the electrical power to the machine and follow lockout/tagout procedures.
– 25 – Separate Electrical Connections Separate electrical connections in the main control box may be required for an optional electric blower dryer heater (when equipped) and for optional electric tank heaters (when equipped) unless equipped with optional circuit breakers.
– 26 – V ent Fan Control Machine electrical circuits can be used to switch a vent fan, supplied by others. On all models, the vent fan is ON when the main power switch is on. The two terminal connections for the vent fan control are both labeled VFC and are provided as a switchingcircuittocontroltheventfan.
– 27 – Final Rinse For FT1000 Base models, the required minimum hot water temperature for the nal rinse is 1 10° F when an electric or steam booster heater is supplied (same connectionpointfor ll).
– 28 – STEAM USAGE / REQUIREMENTS – POUNDS PER HOUR Model T ank Heat Booster 1 10 F Incoming W ater , 75 F Rise Dryer TOT AL T ank Heat & Booster TOT AL T ank Heat, Booster , & Dryer FT1.
– 29 – Auto Clean Hose Connections (When Equipped) Route Auto Clean hoses, located beneath unload section, to appropriate tank barbed connectionttings.
– 30 – Auto Clean Hose Part Numbers T o Each Chamber Machine Conguration ASR Prewash Upper Prewash/wash Lower W ash Upper Power Rinse Dual Rinse Standard w/ ASR 949942-1 949942-2 949942-3 94994.
– 31 – Fig. 32 • T ie a rope to the rst conveyor rod. Feed the rope through the machine following thedesiredpathof theconveyorwiththeight linkspointingup. Theconveyor rollers must be fed between the upper roller guides and the tracks (Fig.
– 32 – • Remove the conveyor roller from one end of the last conveyor rod on the rst section. Then pull the conveyor rod out and save the roller and washers for re- assembly .
– 33 – Conveyor Offset Side Bar Conveyor offset side bars are supplied for use with the standard conveyors and are to be used, if necessary , when making the nal connection to join the two conveyor ends.
– 34 – Fig. 38 NOTE: The proper length of conveyor , when adjusted, will have the ight links close to engaging the load ngers at the load platform.
– 35 – If the conveyor is tracking straight but travels closer to the front (door side) or toward the rear of the machine, then do the following: • If tracking closer to the front, tighten the adjusting bolt on the front take-up unit. • If tracking closer to the rear , tighten the adjusting bolt on the rear take-up unit.
– 36 – Prewash, W ash, and Power Rinse Arms The upper and lower prewash, wash, and power rinse arms must be installed in their correct locations. T o install each of the upper or lower arms, slide manifolds on the supports toward the rear of the machine and ensure the tabs on the sides of the arms drop into the notches in the supports (Fig.
– 37 – Automatic Soil Removal (ASR) Arms (When Equipped) ASR arms must be in their proper locations (Fig. 42). Fig. 42.
– 38 – Bafe Settings The below diagram and chart outlines the standard bafe settings for eachof the machinecongurations.
– 39 – BAFFLE SETTINGS Machine T ype Bafe Setting Machine T ype Bafe Setting Standard Machine 1 Closed Shorty Machine 1 Closed 2 Open 2 Open 3 N/A 3 N/A 4 N/A 4 N/A 5 Closed 5 Closed 6 Close.
– 40 – Lower T rim Panels (Front) and Rear Panels When installing the lower trim panels on the front of the machine, butt each panel end to end. With the bottom of the panel held out on a 45° angle (Fig. 43), hang the upper lip of the panel over the hooks located just below the doors (Fig.
– 41 – This may cause the dish limit arm to trip and stop the conveyor movement. If the conveyor stops for any reason during the 20 minute calibration period, the procedure should be rerun from the beginning to ensure proper calibration. After 20 minutes, unblock the photo detector .
– 42 –.
– 43 –.
– 44 –.
Ein wichtiger Punkt beim Kauf des Geräts Hobart FT1000S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hobart FT1000S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hobart FT1000S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hobart FT1000S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hobart FT1000S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hobart FT1000S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hobart FT1000S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hobart FT1000S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hobart FT1000S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
