Benutzeranleitung / Produktwartung CP-S220W des Produzenten Hitachi
Zur Seite of 26
ENGLISH Liquid Crystal Projector CP-S220W USER'S MANU AL 1-1 Thank you for purchasing this HITACHI liquid crystal projector. Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding.
1-2 FEA TURES This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. • Outstanding brightness The UHB lamp and high-efficiency optical system assure a high level of brightness.
1-3 B B E E F F O O R R E E U U S S E E ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH P art Names Power Switch AC Inlet (to the Power Cord) Ventilation Openings (Intake) ZOOM knob FOCUS ring Rem.
1-4 B B E E F F O O R R E E U U S S E E ( ( c c o o n n t t i i n n u u e e d d ) ) P art Names (continued) VIDEO ST ANDBY/ON POSITION FREEZE MAGNIFY V OLUME AUT O OFF TIMER BLANK MENU SELECT RGB MUTE.
1-5 INST ALLA TION Installation of the Pr ojector and Screen Install the projector in a suitable environment according to instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this manual. Refer to the drawing and table below for determining of the screen size and projection distance.
1-6 I I N N S S T T A A L L L L A A T T I I O O N N ( ( c c o o n n t t i i n n u u e e d d ) ) RGB Signal Input: Connect the RGB IN terminal of the projector to the display signal output of the computer by the enclosed RGB cable. Secure the screws on the connector and tighten.
1-7 I I N N S S T T A A L L L L A A T T I I O O N N ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH Example of system setup AC Input Video tape recorder with S jack Video tape recorder Computer (desktop type) Computer (notebook type) Plug & Pla y This projector is VESA DDC 1/2B compatible.
1-8 OPERA TIONS P ower On/Off Power On 1. Confirm that power cord is connected properly. 2. Push " I " of the power switch. Standby mode is set up and power source indicator burns in the orange. 3. Push a control panel or "STANDBY/ON" of the remote controller.
1-9 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH Basic Operation Basic manipulation to show in the table 1-2 can be done easily by the control panel of projector and the attached remote controller. (The item of ⊕ can manipulate with the control panel.
1-10 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Table 1.2 Basic Operation (continued) Item Description VOLUME Volume adjustment : Reduce VOLUME ↔ Increase VOLUME MUTE ⊕ Set/Clear Mute mode: Press the MUTE! button.
1-11 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH Setup Menu The following adjustments and settings are possible when SETUP is selected at the top of the menu. Part of the Setup menu differs between RGB input and VIDEO/S-VIDEO input.
1-12 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Input Menu The following functions are available when INPUT is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons.
1-13 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH Image Menu The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start operation.
1-14 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Options Menu The following adjustments and settings are available when OPTIONS is selected on the menu. Select an item with the and buttons, and start operation. Table 1.
1-15 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH No Signal Menu The same adjustments and settings are available as with the Image and Options menus when.
* For disposal of used lamp, treat according to the instruction of community authorities. * Since the lamp is made of glass, do not apply shock to it and do not scratch it.
1-17 M M A A I I N N T T E E N N A A N N C C E E ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH Replacing the Lamp 1. Switch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool. 2. Prepare a new lamp.
1-18 M M A A I I N N T T E E N N A A N N C C E E ( ( c c o o n n t t i i n n u u e e d d ) ) Air Filter Maintenance The air filter should be cleaned as described below at intervals of approximately 100 hours. 1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
1-19 ENGLISH TR OUBLESHOO TING OSD Message A message like the bottom table sometimes displays it with this opportunity at the time of power source on. Cope in accordance with the bottom table if message appears on the screen. Table 1-8. Mssage display list.
1-20 T T R R O O U U B B L L E E S S H H O O O O T T I I N N G G ( ( c c o o n n t t i i n n u u e e d d ) ) Indicators Message The POWER indicator, LAMP indicator and TEMP indicator light or blink in the following cases.
1-21 ENGLISH T T R R O O U U B B L L E E S S H H O O O O T T I I N N G G ( ( c c o o n n t t i i n n u u e e d d ) ) Symptom Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.
1-22 SPECIFCA TIONS Item Specification Product name Liquid crystal projector Model CP-S220W Liquid crystal panel Panel size 1.8 cm (0.7 type) Drive system TFT active matrix Pixels 485,616 pixels (604 horizontal x 804 vertical) Lens Zoom lens F=2.0 ~ 2.
1-23 ENGLISH S S P P E E C C I I F F C C A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Dimension Diagram 289 76 45.6 74.5 210 W ARRANTY AND AFTER-SER VICE * When a problem occurs, please check first using the Troubleshooting Chart provided in this instruction manual.
1-24 REGULA TOR Y NO TICES W ARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
9-1 TECHNICAL TECHNICAL Example of computer signal Resolution H × V fH (kHz) fV (Hz) Rating Signal mode Display mode Note 1 640 × 350 37.9 85.1 VESA VGA-1 Zoom in 640 × 400 37.9 85.1 VESA VGA-2 Zoom in 720 × 400 37.9 85.0 VESA TEXT Zoom in 640 × 480 31.
9-2 T T E E C C H H N N I I C C A A L L ( ( c c o o n n t t i i n n u u e e d d ) ) Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to pages 17 and 18 and adjust the V.
Ein wichtiger Punkt beim Kauf des Geräts Hitachi CP-S220W (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hitachi CP-S220W noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hitachi CP-S220W - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hitachi CP-S220W reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hitachi CP-S220W erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hitachi CP-S220W besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hitachi CP-S220W verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hitachi CP-S220W. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hitachi CP-S220W gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.