Benutzeranleitung / Produktwartung SL-350TRSI-AUE des Produzenten Hearth and Home Technologies
Zur Seite of 38
1 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 MODEL: SL-350TRSI-AUE AUSTRALIAN GAS ASSOCIA TION APPROVED Approval Number 5666 THIS MANUAL MUST BE USED FOR INST ALLA TION AND RET AINED BY HOMEOWNER FOR OPERA TION AND MAINTENANCE. HEA T & GLO, a brand of Hearth & Home T echnologies Inc.
2 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 IMPORT ANT : Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty .
3 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 T ABLE OF CONTENTS 1.0 Installation Instructions ......................................................................................... 5 1. 1 Introduction ..........................
4 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 1. Diagram of SL-350TRSI-AUE 22 -3/4 i n. (57 7 mm) 1 1-3 /8 in. (28 9 mm) 16 - 3 /8 i n. (414 mm) 8-3/ 4 in . (223mm) 15 - 7 /8 i n. (402 mm ) Ø 6-5/ 8 in . (16 7 mm) 24 in. (610mm) 5-5/8 in.
5 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 2. Fireplace Dimensions, Locations, and Space Requirements 1.0 INST ALLA TION INSTRUCTIONS Clearance Requirements The top and back of fireplace are defined by stand-offs.
6 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 4. Framing Dimensions Framing should be constructed of 2 X 4 lumber or heavier .
7 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 NOTES: 1. All distances are measured vertically or horizontally along the wall to a point in line with the nearest part of the terminal. 2. Prohibited area below electricity meter or fuse box extends to ground level.
8 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 TABLE 1 1.2 FLUE SYSTEM APPROV ALS These models have flue starting collars on both the top and the back of the unit. Depending upon the installa- tion, decide which ONE set of starting collars will be used to attach the flue system.
9 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 NOTE: PIPES OVERLAP 32mm A T EACH JOINT . D V P 9 0 S T 319m m 286m m 184mm 32mm T YP 13mm T YP 217mm DVP 36 DVP48 1219m m 610m m 914m m 102mm 152mm DVP4 DVP6 305m m DVP 12 51mm MIN . DVP12A 310m m MAX.
10 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 8. SL D-Series Balanced Flue Component S pecifications (102mm inner pipe / 168mm outer pipe) NOTE: PIPES OVERLAP 35mm A T EACH JOINT .
11 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 VERTICAL FLUEING V FT . (M) 36' MAXIMUM (10.97M) Figure 10. USE SL D-SERIES COMPONENTS ONL Y . Figure 1 1. USE DVP-SERIES COMPONENTS ONL Y . STRAIGHT OUT HORIZONT AL FLUEING H Max.
12 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 12. V H FT . (M ) FT . (M ) 1' MIN.(0.30M) 2' MAX.(0.61M) 2' MIN.(0.61M) 4' MAX.(1.22M) 3' MIN.(0.91M) 8' MAX.(2.44M) 4' MIN.(1.22 M) 10' MAX.
13 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 14. V H FT . ( M) FT . (M ) 1' MIN.(0.30M) 2' MAX.(0.61M) 2' MIN.(0.61M) 4' MAX. (1.22M) 3' MIN.(0.91M) 6' MAX. (1.83M) 4' MIN.(1.22M) 8' MAX.
14 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 15. USE DVP-SERIES COMPONENTS ONL Y . FLUEING WITH TWO (2) 90° ELBOWS V H H + H 1 1´ MIN. (0.30M) 1´ MAX. (0.30M) 2´ MAX. (0.61M) 2´ MIN. (0.61M) 2´ MAX. (0.61M) 4´ MAX. (1.
15 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 FLUEING WITH THREE (3) 90° ELBOWS V H H + H 1 FT . (M ) FT . (M ) FT . (M ) 2' MIN.(0.61M) 2' MAX.(0.61M) 4' MA X.(1.22M) 3' MIN.(0.91M) 3' MAX.(0.91M) 6' MAX (1.
16 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 17. FLUEING WITH THREE (3) 90° ELBOWS 1´ MIN. (0.30M) 1´ MAX. (0.30M) 3´ MAX. (0.91M) 2´ MIN. (0.61M) 2´ MAX. (0.61M) 5´ MAX. (1.52M) 3´ MIN. (0.91M) 4´ MAX. (1.22M) 8´ MAX.
17 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 18. WARNING: F AILURE TO REMOVE INSULA TION IN THE SET OF COL- LARS YOU ARE USING COULD CAUSE A FIRE. WARNING: THE REAR FLUE COL- LAR SEAL CAP MUST REMAIN A T - T ACHED TO THE REAR FLUE COL- LARS IF THE FLUE SYSTEM IS A T - T ACHED TO THE T OP ST ARTING COLLARS.
18 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 ! W ARNING: ENSURE THA T THE HEA TER GASKET SUPPLIED WITH THE HEA TER SEALS BETWEEN THE FIRST FLUE COMPO- NENT AND THE OUTER HEA TER WRAP . Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 38 mm.
19 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 2. Continue Adding Flue Components T o continue adding flue components in accordance with the pre-planned flue system configuration: • Ensure that each succeeding flue component is se- curely fitted and locked into the preceding compo- nent in the flue system.
20 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 For V ertical Runs The flue system must be supported every eight (8) feet (2.4 M) above the heater flue outlet by wall brackets.
21 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 ! Figure 27. Ceiling Firestop (Ceiling Side) If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.
22 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 For V ertical T erminations - T o locate the flue and install the flue sections: • Locate and mark the flue centerpoint on the under- side of the roof, and drive a nail through the centerpoint.
23 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 1.4 IGNITION SYSTEM WIRING • This gas heater is equipped with an electronic igni- tion system which operates on a 6 volt system. • This appliance requires 240 V AC to be wired to the factory installed junction box.
24 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 32. NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE RE- PLACED, IT MUST BE REPLACED WITH TYPE 105 • C RA TED WIRE.
25 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 34. 1.6 FINISHING The minimum clearance to combustibles are 0 from the sides, floor , back and top (these clearances are defined by the standoffs). The minimum distance to the perpendicular side wall extending past the appliance front is 2-inches (51mm).
26 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 35. Figure 36. MAKE SURE THE FLAMES ARE STEADY—NOT LIFTING OR FLOA TING . Inst alling the T rim Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face.
27 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 1 2 3 4 5 6 1.8 LOG PLACEMENT INSTRUCTIONS Log Set Assembly: LOGS-350CE-D Carefully remove the logs from the packaging. CAUTION: Logs are fragile! LOG #1 (SRV327-701): Place log #1 at the rear of the unit, with the left edge behind the tab on the pilot bracket.
28 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 LOG #3 (SRV705-703): Rest log #3 against the right front grate corner and place its slot over the right burner tab. LOG #4 (SRV530-716): Place the left end of log #4 in the groove on log #2 and the right end on log #1 as shown.
29 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 LOG #6 (SRV540-704): Place log #6 against the second and third grate bars. If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingement.
30 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 ! ! OPERA TING CAUTIONS • This appliance may exhibit a slight carbon deposition. • Do not place articles on or against this appliance. • Do not use or store flammable materials near this appliance.
31 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 2.1 SAFETY & LIGHTING INFORMA TION Follow SAFETY INFORMA TION and LIGHTING IN- STRUCTIONS to light the appliance. By design, the flame pattern will not be identical from unit to unit.
32 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 ! 2.2 F AN OPERA TION The accessory fan is wired in series with a speed con- trol switch and a temperature sensor switch. Set the speed control to an "ON" position and light the heater .
33 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 PILOT B RACK ET RET AINI N G SC REWS 3.1 REMOV AL OF COVERS FOR SERVICING A . Control Compartment Door • Rotate the lower door down to access the gas controls. B . Dress Guard and Glass Door • Lift the front dress guard up and out away from the appliance side surrounds.
34 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 3.5 TROUBLESHOOTING SL-350TRSI-AUE With proper installation and maintenance, your new Gas Heater should provide years of trouble-free service. If you do experienc e a problem, refer to the T rouble Shooting Guide below .
35 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 (NG , LP) Exploded Parts Diagram Service Parts SL-350TRSI-AUE Beginning Manufacturing Date: 6/06 Ending Manufacturing Date: ______ 22 Log set assembly 2 13 4 10 16 15 14 12 7 8 11 21 32 31 23 25 27 24 26 28 18 4.
36 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 SL-350TRSI-AUE Service Parts List IMPORT ANT : When ordering, supply serial and model numbers to ensure correct service parts.
37 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 LIMITED 10 YEAR WARRANTY HEAT & GLO, a brand of Hearth & Home Technologies Inc.
38 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 For Service or Replacement Part s Contact: Melbourne Jetmaster 444 Swan S treet Richmond 3121 (03) 9429-5573 Perth Fireplace Corner 2.
Ein wichtiger Punkt beim Kauf des Geräts Hearth and Home Technologies SL-350TRSI-AUE (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hearth and Home Technologies SL-350TRSI-AUE noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hearth and Home Technologies SL-350TRSI-AUE - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hearth and Home Technologies SL-350TRSI-AUE reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hearth and Home Technologies SL-350TRSI-AUE erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hearth and Home Technologies SL-350TRSI-AUE besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hearth and Home Technologies SL-350TRSI-AUE verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hearth and Home Technologies SL-350TRSI-AUE. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hearth and Home Technologies SL-350TRSI-AUE gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
