Benutzeranleitung / Produktwartung 407D des Produzenten Hayter
Zur Seite of 28
POWERTRIM Code 407D OWNER’S HANDBOOK FROM SERIAL NO:407D001001 P ART NO: 1 1 1-0443 (rev .0.) ISSUE: 01-20-06.
2 276798MA DRAFT COPY T ABLE OF CONTENTS OWNER’S INFORMA TION 4 SAFETY PRECAUTIONS 4 INTERNA TIONAL PICTORIALS 7 ASSEMBL Y 8 OPERA TION 1 1 MAINTENANCE 14 TROUBLE SHOOTING CHART 20 REP AIR P ARTS 22 Declared vibration emission values in accordance with Directive 98/37/EC.
3 276798MA DRAFT COPY Hayter Limited warrants to the original user / purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase.
SAFETY RULES 4 276798MA DRAFT COPY OWNER’S INFORMA TION Know your product: If you understand the unit and how the unit operates, you will get the best performance. As you read this manu- al, compare the illustrations to the unit. Learn the location and the function of the controls.
SAFETY RULES 5 276798MA DRAFT COPY 18. Before each use, inspect the throttle control lever and cable. Make sure that the cable is free and that the lever is not damaged. Also check the cable linkage running to the carburetor for kinks, loose fittings, and obstructions.
SAFETY RULES 6 276798MA DRAFT COPY 2. Never run an engine indoors or inside a closed area. 3. Never make adjustments or repairs with the engine running. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental start- ing.
SAFETY RULES 7 276798MA DRAFT COPY INTERNA TIONAL PICTORIALS IMPORT ANT : The following pictorials are located on your unit or on literature supplied with the product.
ASSEMBL Y 8 276798MA DRAFT COPY ASSEMBL Y CONTENTS OF P ARTS BAG 1 − Owner ’s Manual 1 − Parts Bag 1 − Safety Glasses (Not shown actual size) 2 Sets − T rimmer Lines (0.155 inch diameter) 1 − Bag (4 Screws) 1 − 20 oz. Bottle Oil W ARNING: Always wear safety glasses or eye shields while as- sembling the machine.
ASSEMBL Y 9 276798MA DRAFT COPY HOW TO RAISE THE HANDLE 1. Hold the handle with one hand and loosen both handle adjustment knobs until the ratchet teeth are disengaged. Do not remove the handle adjustment knobs . See Figure 2. 2. Raise the handle to the operating position.
ASSEMBL Y 10 276798MA DRAFT COPY ENGINE PREP ARA TION Note: Engine does not contain OIL or PETROL. W ARNING: Follow the engine manufacturer ’s instructions for the type of petrol and oil to use. Always use a safety petrol container . Do not smoke when adding petrol to the en- gine.
OPERA TION 11 276798MA DRAFT COPY KNOW YOUR POWERTRIM READ THE OWNER’S HANDBOOK AND ALL SAFETY RULES BEFORE YOU OPERA TE the machine. T o familiarise yourself with the location of the controls, compare the illustrations with your machine. Save this handbook for future reference.
OPERA TION 12 276798MA DRAFT COPY HOW TO USE THE TRIMMER HEAD DRIVE LEVER 1 . T o engage the trimmer head, hold the con - trol bail against the handle . Move the trimmer head drive lever forward to en- gage the trimmer head. See Figure 6. The faster the engine runs, the faster the trim- mer head will rotate.
OPERA TION 13 276798MA DRAFT COPY HOW TO ST ART THE ENGINE NOTE: DO NOT BE ALARMED, your engine will smoke the first time it is started. It is burning off the protective coating that is on the internal engine parts. W ARNING: Never leave the ma- chine unattended while the en- gine is running.
MAINTENANCE 14 276798MA DRAFT COPY CUST OMER RESPONSIBILITIES SER VICE RECORDS Fill in dates as you complete regular service. Before Each Use Every 5 Hours Every 25 Hours Every 100 Hours As Noted SER .
MAINTENANCE 15 276798MA DRAFT COPY LUBRICA TION How T o Lubricate The Jackshaft Assembly A grease fitting is provided to lubricate the jackshaft assembly . Use a grease gun with a u- tomotive type grease to lubricate the jackshaft assembly as shown in Figure 10.
MAINTENANCE 16 276798MA DRAFT COPY SP ARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted or burned or if the porcelain is cracked. 1 . Make sure the spark plug is clean. Clean the spark plug by carefully scraping the electrodes (do not sand blast or use a wire brush).
MAINTENANCE 17 276798MA DRAFT COPY SER VICE AND ADJUSTMENT W ARNING: Before you inspect, clean or service the machine, stop the engine. Make sure that all moving parts have stopped. Disconnect the wire from the spark plug. HOW TO REPLACE THE TRIMMER LINE For the best performance, use a heavy gauge 3.
MAINTENANCE 18 276798MA DRAFT COPY HOW T O REPLACE THE DRIVE BEL T T o replace the drive belt, the trimmer head and shield must be removed as follows. W ARNING: Before you remove the drive belt, disconnect the wire from the spark plug. 1. Remove the two fasteners that hold the rear o f the shield to the trimmer housing (See Figure 14) .
MAINTENANCE 19 276798MA DRAFT COPY STORAGE W ARNING: Do not remove petrol while inside a building, near a fire, or while you smoke. Petrol fumes can cause an explosion or a fire. When the machine is put in storage for thirty days or more, follow the steps below to make sure the machine is in good condition the following season.
TROUBLE SHOOTING CHART 20 276798MA DRAFT COPY TROUBLE CAUSE CORRECTION Engine does not start Spark plug wire disconnected. Connect spark plug wire. Engine not primed. Prime engine. Defective or incorrectly gapped spark plug. Inspect or replace spark plug.
TROUBLE SHOOTING CHART 21 276798MA DRAFT COPY Engine overheats. Engine cooling system clogged. Clean debris screen and engine cooling fins. Carburetor out of adjustment. Adjust carburetor . T ake the unit to an authorised Service Dealer . Oil level is low .
Code 407D REP AIR P ARTS 22 276798MA DRAFT COPY 1 2 3 4 5 28 6 2 7 6 8 4 9 10 9 10 4 11 16 17 11 14 12 15 14 20 22 29 23 27 16 19 30 17 6 20 25 24 26 19 18 18 13 31 21 32 33 34.
Code 407D REP AIR P ARTS 23 276798MA DRAFT COPY Key No. Part No. Description 1 MU740198E549 Lever , Stop 2 MU323035 Bolt 3 MU740193 Cable, Control Latching 4 MU071372 T ie, Cable 5 MU740196E701 Handle.
Code 407D REP AIR P ARTS 24 276798MA DRAFT COPY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 17 18 19 20 22 23 24 25 26 27 29 30 31 31 33.
Code 407D REP AIR P ARTS 25 276798MA DRAFT COPY Key No. Part No. Description 1 MU015x84 Nut 2 MU025x1 1 Screw 3 MU740150E549 Frame, T rimmer 4 MU26x256 Screw 5 MU740231 Z Bracket, Idler Assembly 6 MU0.
NOTES 26 276798MA DRAFT COPY.
NOTES 27 276798MA DRAFT COPY.
28 276798MA DRAFT COPY How T o Order Replacement Parts Use only manufacturer ’s authorised or approved replacement parts. The letter placed on the end of the part number denotes the type of finish for the part, C for chrome, Z for zinc, a P A for purchased assembly .
Ein wichtiger Punkt beim Kauf des Geräts Hayter 407D (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hayter 407D noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hayter 407D - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hayter 407D reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hayter 407D erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hayter 407D besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hayter 407D verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hayter 407D. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hayter 407D gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
