Benutzeranleitung / Produktwartung Flextight 646 des Produzenten Hasselblad
Zur Seite of 30
User's Guide Flextight 646 English.
© 2004 Hasselblad A/S. All rights reserved. Flextight 646 User's Guide, Part No 70030050, revision A. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hasselblad A/S.
Table of Contents User's Guide - Flextight 646 Table of Contents 3 English Hardware Reference - Flextight 646 5 Warnings and Restrictions 6 System Requirements 7 Front Panel 9 Back Panel & Co.
User's Guide - Flextight 646 4 English.
Hardware Reference - Flextight 646 This manual provides important information about using your Flextight 646 scanner. Topics include: • Important warnings and restrictions • System requirements .
Warnings and Restrictions • Read all of the included documentation before attempting to install and use the scanner. • Do not touch the originals and/or the original holder while scanning. • Do not start scanning or previewing until an original holder with an original has been mounted.
System Requirements Below are the basic hardware requirements for the PC or Macintosh system to which the scanner is to be connected. For information about the processor, operating system, RAM and harddisk requirements please refer to the “Software Reference” manual, that comes with the FlexColor software.
User's Guide - Flextight 646 Hardware Reference - Flextight 646 8 English.
Front Panel A Feed Table: place original holders here for scanning. B Light Area: for viewing originals. The grid helps you to align your transparent originals. C Transparency Holder Guide : all transparency holders fit between two rails to keep them straight.
Back Panel & Connectors A Power Cable Socket: plug the power cable into this socket. B FireWire Interface Sockets: plug a FireWire cable (max. 6 m) here and connect it to your computer. You can use the second plug to connect another device (hard disk, printer etc.
Cut-Away View A CCD Housing: this movable platform contains the light sensor and holds the optics. B Positioning Lead Screws: for positioning of the CCD housing and optics housing for the appropriate resolution and original size. C Optics Housing: focuses the image of the original on the CCD.
Setting up the Scanner Environmental Requirements Set up the scanner in a location that fulfils the following requirements: • Keep the scanner away from sources of heat, such as direct sunlight or a radiator. Warm temperatures will degrade the quality of your scans - for best results, work in a cool environment.
Installation Procedure, FireWire Interface 1. Place the scanner on a table near your computer with the front facing away from you. Make sure that the location you choose meets all environmental - and electrical requirements as described on page 11. 2.
Attaching/Detaching the Feed Table To attach the feed table correctly onto the scanner lead the brackets (B) as far as they go into the slits (C) in the scanner base, then lower the table and pull it slightly backwards to ensure that the notches (D) catch the bottom of the slits.
Mounting/Dismounting of the Cabinet To dismount the cabinet (A) remove the two screws (B) at the scanner back using a 2.5 mm allen key, then pull the cabinet upwards.
User's Guide - Flextight 646 Hardware Reference - Flextight 646 16 Operating the Scanner English FLEXTIGHT ORIGINAL HOLDER PATENTPENDING à à E à à A D B C à à K L J F H G à M Figure 6: Ope.
Operating the Scanner (See Figure 6 opposite). 1. It is assumed that the scanner and FlexColor software have been properly installed. 2. Make sure that the feed table (A) has been attached properly onto the scanner (see “Attaching/Detaching the Feed Table” on page 14).
User's Guide - Flextight 646 Hardware Reference - Flextight 646 18 Operating the Scanner English FLEXTIGHT ORIGINAL HOLDER PATENTPENDING à à E à à A D B C à à K L J F H G à M Figure 6: Ope.
8. Lift the top layer of the original holder and place your original as follows: • For transparencies, place your original (G) with the emulsion side down. The original must completely fill the hole with no edges showing and with a minimum overlap of 2mm along each edge.
Resolutions True Resolutions The table below shows the max. resolutions (in ppi) available with each of the original holders when scanning in True Resolutions mode. Calibrating the Scanner The scanner requires two types of calibration: • Focus calibration adjusts the positioning of the scanner 's optics for each zoom level.
Focus Calibration The Flextight 646 scanner uses an adjustable zoom and focus mechanism to optimize its scanning resolution for each of the original formats it can handle. If you suspect your scans are not as sharp as they should be, then you may need to calibrate your scanner.
White Calibration for Reflectives The Flextight scanner uses a white reference to make sure that all elements in the scanner's CCD react consistently to light brightnesses. The scanner has been calibrated from the factory, and the calibration data is stored in the scanner ’s flash PROM.
5. Click on Calibrate . The scanner will take several scans of the white target. The process will take about eight minutes. User's Guide - Flextight 646 Hardware Reference - Flextight 646 23 Cali.
User's Guide - Flextight 646 Hardware Reference - Flextight 646 24 Replacing the Light Tubes English PRESS PULL OUT PULL OUT PRESS à D E C B A Figure 9: Replacing the Light Tubes.
Replacing the Light Tubes General The Flextight 646 contains two light tubes: one for illuminating reflective originals from above, the other for shining light through transparencies from below.
User's Guide - Flextight 646 Hardware Reference - Flextight 646 26 Replacing the Light Tubes English PRESS PULL OUT PULL OUT PRESS à D E C B A Figure 9: Replacing the Light Tubes.
9. Connect the plug (C) . 10. IMPORTANT: The "T" on the lamp board cover (E) indicates the socket for the transparencies tube. 11. Mount the cabinet (B) and the feed table (A) following the reverse of the procedure used when removing them. NOTE! When mounting the cabinet (B) make sure that it goes free of all cables and extrusions.
Technical Specifications Power Connector: Power Consumption Max. 60 W during operation Power Requirements 100-240V AC, 1.3A, 50-60Hz Interface to Computer FireWire (IEEE 1394) Front Panel One multifunction switch (on/off switch) with integrated status light Drum Force 1kg (2.
FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE - Declaration of Conformity User's Guide - Flextight 646 Hardware Reference - Flextight 646 30 CE - Declaration of Conformity English HASSELBLAD A/S HEJREVEJ 30 DK - 2400 COPENHAGEN NV TELEPHONE +45 7026 0800 TELEFAX +45 7026 0900 REG./VAT NO.
Ein wichtiger Punkt beim Kauf des Geräts Hasselblad Flextight 646 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hasselblad Flextight 646 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hasselblad Flextight 646 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hasselblad Flextight 646 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hasselblad Flextight 646 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hasselblad Flextight 646 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hasselblad Flextight 646 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hasselblad Flextight 646. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hasselblad Flextight 646 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
