Benutzeranleitung / Produktwartung PUB 0804 des Produzenten Hasbro
Zur Seite of 18
1 Illuminator Glider Door Installation Manual Ultimate Products Inc. • 2319 Laurelbrook Street• Raleigh, NC 27604 • (800) 542 - 7221 • Fax (919) 834 - 4526 PUB 0804.
2 Tools required for Installation Items needed but not included: Screws for mounting track assembly. Impact Wrench Electric or cordless drill Set of drill bits 1/4” to 9/16” Set of box - end wrenc.
3 Parts Identification GLP2003 - Glider Pulley with Bolt and Nut CV100: Cam Valve QD100: Quick Exhaust Valve AP1078: Male Tube Stem AP1075: 3/8" x 1/4" Reducing elbow quick connect AP1080: 3.
4 Parts Identification Continued E - 1 E - 2 A - 1 A - 2 B - 2 B - 1 C - 2 C - 1 D - 2 D - 1 C - 1: Left Hand Slotted Glider Stop C - 2: Right Hand Slotted Glider Stop B - 1: Left Hand Glider Stop B -.
5 Insure that Walls on each side of door opening are clear of all obstructions (Door will protrude 5 1/2” Into building) Install bottom of door track 1” above door opening Door Opening 1” A 1 2 .
6 Panel #1 Panel #2 Panel #3 Panel #4 Panel Identification: Install all panels w/ center Brace on inside of building.
7 Slide Panel #1 & 2 (see page 4) Into track #1 As shown in figure C and step number 6 below. Make sure center brace is on the inside of building 5 C Slide Panel #4 (Clear Section) Into track #2 A.
8 9 Slide panels #2 and #3 to the right hand side of track - The track that does not have the operator Place all panels as shown on page 4 so the door is in the closed position 10 Preparing to install.
9 11 Install Blocks on Door Sections Panel #2 Panel #4 B - 1 C - 1 D - 1 Install Items ‘B - 1,C - 1, and ‘D - 1’ on Panel #2 and Panel #4 as shown Install Items ‘B - 2’, ‘C - 2’ and ‘D.
10 12 Install Items ‘A - 1’and‘A - 2’ Panel #2 Panel #4 A - 1 With Door Sections in Closed position: Install item ‘A - 1’ on Panel #2. The guide bar is inserted into slot of A - 1 as shown.
11 13 Install Items ‘E - 1’and ‘E - 2’ Keeping Door in Closed Position: Insert item ‘E - 1’ onto guide bar of panel #2 and attach to wall with screws.
12 16 Install Bracket ‘A’ Slide Bracket ‘A’ onto operator rod and position bracket ‘A’ 3” from edge of door as shown on step #17. Now attach aluminum block to operator rod as shown 17 A B A 3” 3” *Important: Push Operator Rod fully into cylinder.
13 Air Powered Operator Track 33” minimum 33” minimum 8 1/4” Door Opening Door Opening 20 Run cable around top of pulley on right side of track and through top slot of aluminum block on bracket ‘B’ (do not tighten block until later) 19 Run cable through top slot of bracket ‘A’: A Tighten bolts of aluminum block down onto cable.
14 22 Install brush on bottom of door sections Install brush on bottom of each panel so that brush angles in- ward as shown. (Brushes will angle toward each other) Bottom of brush should touch floor for a proper seal.
15 23 Install floor guides J K Space Items ‘J’ & ‘K’ 2 1/4” apart Make sure center of floor guides are in center of door opening Place item ‘J’ even w/ door opening 24 Install Air Fi.
16 Left side of operator (inside looking at door) Right side of operator (inside looking at door) A A B C D H G F E J I B D Connect Air line from “A” (left side of operator) to “F” Connect Air.
17.
18 Door opening requirements for Glider Door For 10’ opening — Minimum of 33” of side room on each side Operator will open the door 9’9” wide leaving 1 1/2” of door in opening Make Floor level! Track and operator weight approx. 155 pounds.
Ein wichtiger Punkt beim Kauf des Geräts Hasbro PUB 0804 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hasbro PUB 0804 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hasbro PUB 0804 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hasbro PUB 0804 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hasbro PUB 0804 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hasbro PUB 0804 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hasbro PUB 0804 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hasbro PUB 0804. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hasbro PUB 0804 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.