Benutzeranleitung / Produktwartung 90692 des Produzenten Harbor Freight Tools
Zur Seite of 14
LA THE DUPLICA T OR A TT A CHMENT (FOR USE WITH LA THE MODEL 90265) MODEL 90692 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http//www .harborfreight.com Cop yr ight 2003 by Harbor F reight T ools.
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep your in voice with this man ual.
SKU 90692 P A GE 3 3. Store idle equipment. When not in use, tools and equipment should be stored in a dr y location to inhibit rust. Alwa ys lock up tools and equipment, and k eep out of reach of children. 4. Do not use this product if under the influence of alcohol or drugs.
SKU 90692 P A GE 4 cannot cov er all possible conditions and situations that ma y occur . The operator must understand that common sense and caution are factors, which cannot be b uilt into this product, but must be supplied b y the operator . SPECIFIC PRODUCT W ARNINGS AND PRECA UTIONS 1.
SKU 90692 P A GE 5 ASSEMBL Y INSTR UCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 14 . T o Attac h The T ool Rest Base: 1. Loosen the T ool Rest Handle of the lathe , and slide the T ool Rest Base of the lathe to as near the Headstock of the lathe as possibl e.
SKU 90692 P AGE 6 3. Install one Low er V er tical Suppor t Bar (46) onto the T ool Rest Base of the lathe , and secure it by tightening the Suppor t Bar Handle of the lathe. (See Figure A.) 4. Loosen the T ailstock Handle of the lathe , and remov e the T ailstock from the Bed of the lathe .
SKU 90692 P AGE 7 U-BRACKET (38) HANDLE (3) P A TTERN SUPPORT B AR (41) P A TTERN BOL T (42) LOWER VERTICAL SUPPORT BAR (46) U-BRACKET ASSEMBL Y LOWER VERTICAL SUPPORT BAR (46) U-BRACKET ASSEMBL Y FIGURE C T o Attac h The Suppor t Bar: 1. Remove the End Cap (12) from each end of the Support Bar (54).
SQUARE NUT (47) SQUARE NUT (47) SUPPORT BAR (54) FLA T W ASHER (40) LOCKW ASHER (34) HANDLE (48) FLA T W ASHER (40) LOCKW ASHER (34) HANDLE (48) FIGURE D T o Assemb le The T ool Holder: 1. Loosen the two Set Scre ws (20) on the T ool Holder (24), and e xtend the Cutting T ool (31) out about 4 inches.
T o Attac h The T ool Holder Assemb l y: 1. Slide the Cutting T ool (31) of the T ool Holder (24) into the Slot located on the Side Plate (50). (See Figures E and F .) 2. Attach the Spring (19) over the Pointer (14) on the Side Plate (50). (See Figure F .
FIGURE G SAFETY SHIELD (8) HANDLE (51) SAFETY SHIELD PLA TE (43) SUPPORT BAR (54) BOL T P AN HEAD SCREW (9) FLA T W ASHER (21) HEX NUT (7) HEX HEAD BOL T (11) FLA T W ASHER (40) HEX NUT (39) OPERA TING INSTRUCTIONS T o Adjust The Cutting T ool: 1.
3. The Cutting T ool (31) also can be adjusted vertically by loosening the Soc ket Head Bolt (25) which secures the T ool Holder (24) in place. Once adjusted, make sure to re-tighten the Socket Head Bolt.
SKU 90692 P A GE 12 occurs, have the problem corrected before further use. Do not use damaged equipment. 2. F or better and safer perf or mance, alw ays k eep the Cutting T ool (31) clean and sharp. 3. Daily , with a clean cloth, br ush, or vacuum remo ve all debris fromthe Lathe Dupli- cator Attachment.
P AR TS LIST SKU 90692 P AGE 13 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ARTS LIST AND ASSEMBL Y DIA GRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y .
NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not available individually as replacement parts. ASSEMBL Y DIA GRAM SKU 90692 P AGE 14 12 38 3 45 2 39 41 42 49 54 53.
Ein wichtiger Punkt beim Kauf des Geräts Harbor Freight Tools 90692 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Harbor Freight Tools 90692 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Harbor Freight Tools 90692 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Harbor Freight Tools 90692 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Harbor Freight Tools 90692 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Harbor Freight Tools 90692 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Harbor Freight Tools 90692 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Harbor Freight Tools 90692. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Harbor Freight Tools 90692 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.