Benutzeranleitung / Produktwartung MAN-782-CH4 des Produzenten American Megatrends
Zur Seite of 26
Megaplex II 4U Chassis Guide MAN-782-CH4 1/28/00.
ii Megaplex II 4U Chassis Guide © Copyright 2000 American Megatrends, Inc All rights reserved All rights reserved. American Megatrends, Inc. 6145F Northbelt Parkway Norcross, GA 30071 This publication contains proprietary information which is protected by copyright.
Preface iii Table of Contents Safety Summary ...................................................................... vi 1 Gen eral Information ..................................... 1 General Description of Chassis ......................................
iv Megaplex II 4U Chassis Guide Preface Limited Warranty The buyer agrees if this product proves to be defective, that American Megatrends is obligated only to repair or replace this product at American Megatrends’ discretion according to the terms and conditions of the warranty registration card that accompanies this product.
Preface v Preface, Continued Disclaimer This manual describes the operation of the American Megatrends Megaplex II 4U chassis. Although efforts have been made to assure the accuracy of the information.
vi Megaplex II 4U Chassis Guide Safety Summary The following text describes the WARNINGS, CAUTIONS, and NOTES used throughout this document. Each description is followed by an example. You should become familiar with these procedures and always observe standard safety practices.
Chapter 1 General Information 1 1 General Information This manual provides general installation and maintenance information, including drive installation and power supply replacement for the Megaplex II 4U chassis. General Description of Chassis The Megaplex II rack-mount chassis supports up to three 3.
2 Megaplex II 4U Chassis Guide Front of Chassis Back of Chassis.
Chapter 1 General Information 3 Specifications This chassis is designed to be used in 19” rack configurations. This chassis has been designed to hold the Megaplex II motherboard configured with up to 2 GB of memory. The specifications of the chassis are: Dimensions Height: 7”, Width: 19”, Depth: 28” Weight : Approximately 50 pounds.
4 Megaplex II 4U Chassis Guide Specifications, Continued SCSI Drives The 4U chassis supports three hot plug 3.5” 16-bit single-ended SCA LVD SCSI drives. • These drives are accessible from the front. • Each drive bay can take a 1” SCSI LVD drive.
Chapter 1 General Information 5 Specifications, Continued LEDs and Switches There are fan failure LEDs for both fans. There is an IDE Activity LED , a power-on LED, a reset switch, and a power-on switch. There are four CPU Activity LEDs . There are three SCSI LEDs .
6 Megaplex II 4U Chassis Guide Cooling Fans There are three fans in the front of the of the Megaplex II chassis. They are located on the right side of the front grill. There are two fans in the middle of the of the Megaplex II chassis. They slide down into the slot in the middle of the chassis.
Chapter 1 General Information 7 Connectors on Back of Chassis The back of the chassis has connectors for the keyboard, mouse, serial ports (1 and 2), parallel port, and VGA port.
8 Megaplex II 4U Chassis Guide Drive Bays on Front of Chassis There are three drive bays on the front of the chassis. The drive bays are located beneath the floppy disk drive on the left side of the chassis.
Chapter 2 Installation 9 2 Installation Unpacking and Inspection Unpack the Megaplex II chassis and visually inspect it for damage that might have occurred during shipment. Retain the shipping carton in case reshipment is necessary. Remove the top cover of the chassis and inspect for component damage.
10 Megaplex II 4U Chassis Guide Drive Installation Before installing drives make sure that the chassis is powered down. Step 1 Unscrew the thumbscrews on the front cover to access the drive bays. Step 2 Unscrew the thumbscrew at the top of the mounting bracket where the new drive is to be installed.
Chapter 2 Installation 11 Drive Installation , Continued Step 4 Slide the bracket out. Step 5 Mount the disk drive on the front side of the mounting br acket.
12 Megaplex II 4U Chassis Guide Drive Installation , Continued Step 6 Line up the holes in the brackets and the screw holes in the back of the drive. The back of the bracket is shown below. Step 7 Insert the screws through the screw holes and the brackets and tight en all four screws.
Chapter 2 Installation 13 Rack-Mount Installation Before the unit is installed into a rack the following items should be taken into consideration: • The maximum ambient temperature of this unit is 40 ° C. Internal temperatures of the rack assembly should be considered for safe operation.
14 Megaplex II 4U Chassis Guide Rack-Mount Installation, Continued Step 3 Position the outer rails in the rack, adjusting the claw brac kets and marking the intended position of the mounting holes both on the front and rear of the rack. Tighten the screws on the claw brackets.
Chapter 3 Field Replaceable Units 15 3 Field Replaceable Units The field replaceable subassemblies within the Megaplex II chassis are described below. The subassemblies in this section are: • the power supply assemblies and • the fan module assemblies.
16 Megaplex II 4U Chassis Guide Replacing a Power Supply The power supply module is hot pluggable. You do not have to shut down the system to replace a power supply. Step 1 Unplug the AC power cord connected to the failed power supply module. Step 2 Loosen the thumbscrews that secure the power supply module.
Chapter 3 Field Replaceable Units 17 Replacing a Fan Module The chassis mounted fan assembly is easily removed and replaced. Should the fan assembly need replacement use the following procedure. The fan assembly is hot pluggable. You do not have to shut down the system to replace a fan.
18 Megaplex II 4U Chassis Guide.
Index 19 Index A AC Input , 3 Alarm Mute switch, 4 Altitude , 5 B Back of Chassis, 2 C Chassis Alarm Indication, 4 Chassis Intrusion, 4 chassis slides, 14 claw brac, 14 claw brackets, 13 Connectors on.
20 Megaplex II 4U Chassis Guide U Unpacking , 9 W Web Site, iv Weight, 3.
Ein wichtiger Punkt beim Kauf des Geräts American Megatrends MAN-782-CH4 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie American Megatrends MAN-782-CH4 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für American Megatrends MAN-782-CH4 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von American Megatrends MAN-782-CH4 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über American Megatrends MAN-782-CH4 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon American Megatrends MAN-782-CH4 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von American Megatrends MAN-782-CH4 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit American Megatrends MAN-782-CH4. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei American Megatrends MAN-782-CH4 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
