Benutzeranleitung / Produktwartung SpeedDome Ultra VII EIS des Produzenten American Dynamics
Zur Seite of 37
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 1 of 37 S peedDome ® Ultra VII EIS Day/Night Camera Dome Installation and Service Guide Figure 1.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 2 of 37 About the Camera Dome The SpeedDome Ultra VII EIS day/night camera dome ( Figure 1) comes in .
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 3 of 37 Indoor Ceiling Mounting Using hardwa re shi pped with the base, the camera dome attaches directly to indoor ceilings made of sheet rock, wood, metal, or concrete ( Figure 3).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 4 of 37 Figure 4. Indoor mounting structures (option al) RHIUF B RHIUAB RHIUHC RHIU2 X2 RHIUTH RHIUTR.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 5 of 37 Outdoor Mounting (Optional) Note: This document doe s not inclu de outdoor installation and service instructions. Fo r these instructions, see RHODUL Outdoor Hou sing Install Guide 8200-0492-01.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 6 of 37 Figure 7. Outdoor mounting structures (optional).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 7 of 37 Cable Requirement s Dat a Cable The table below shows requirements for SensorNet, RS-422, and Manchester net works.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 8 of 37 T wisted Pair Adapter Figure 8. Twisted Pair Adapter The supplied ADACTP01BNC Twiste d Pair A.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 9 of 37 Power-Up Routine After power is connected to the dome, the dome performs the following hom ing routin e. 1. After a few seconds, the camera lens tilts up into the housing and eyeball assembly.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 10 of 37 ! WARNING! EU power requirements: This product runs o n 24Vac.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 11 of 37 Indoor Inst allation This section explains how to conn ect th e housing and eyeball assembly.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 12 of 37 Use the following addresses for the prot ocol s shown: PROTOCOL SW3 SW2 SW1 AD Manchester , .
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 13 of 37 4. For the dome at the end of a daisy chain, set termination jumper JW1 on the dome CP U board ( Figure 13) to “terminated.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 14 of 37 6. Connect the 4-pin plug (alarm input/output) to the 4-pin receptacle ( Figu re 14). a. Feed the cable through the access hole in the base. b.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 15 of 37 Checking Power and Data for Domes Using the Base without I/O Board Check LEDs to verify that power and data are reaching the dome ( Figure 16).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 16 of 37 Manchester: After approximately 20 secon ds, the three LEDs do the followi ng: Red Green Yellow Possible Cause Blinking Steady, Blinking, then Steady 1 Steady, then Off 2 White (pin1) and black (p in 2) correctly wired.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 17 of 37 Connecting to a Mounting Base with I/O Board This procedure explains how to conne ct the housing and eyeball assembly to a mounting ba se with I/O board.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 18 of 37 4. Connect the alarm output cable, if used, to the P3 connector. Pin Color Desig nation 1 — 12Vdc (1 00mA max.) 2 — 12Vdc (1 00mA max.) 3 — Output P0 (40m A s ync.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 19 of 37 10. Set the dome address ( Figure 19 ). Figure 19.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 20 of 37 Using the Inst all/Removal T ool CAUTION: Do not use this tool to conne ct the dome to the s.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 21 of 37 Figure 21. How to use the install/removal tool Dome Connection (reverse steps to disconnect).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 22 of 37 T roubleshooting Indoor Domes CAUTION: This troublesh ooting sectio n is for indoor camera domes only! To trouble shoot outdoor domes, see install ation and service manual shipped with the outdoor h ou sin g.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 23 of 37 3. Detach dome from base an d examine address switches. Are they set correct ly ? YES If dome still doesn't respond, contact your sales representative for repair instructions .
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 24 of 37 7. Observe yellow comm. LED (CR28) on I/O board ( Figure 23). Is the LED on or flashing? YES Go to s tep 8. NO Verify cable is properly attached by referring to table in step 9, page 17.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 25 of 37 Detailed Troubleshooting Use this procedure to deter mine if the problem is a simple cable conne ction or a major com pone nt. To perform this procedure, you must open the housing and eyeball assembly.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 26 of 37 Disassembling the Dome CAUTION: Once disa ssem bled, parts of dome housing and eyeball assembly are "extremely fragile" and may break.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 27 of 37 Removing the P/S Board CAUTION: Electrostatic-se nsitive device. Use a ground strap whe n han dling power supply board. Referring to Figure 25.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 28 of 37 Removing the Slot Covers 1. Gently swivel eyeball to totally expose one of two slot covers ( Figure 27). CAUTION: Swiveling fast can damag e gears.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 29 of 37 Detaching the Eyeball 1. Perform procedure "Remo v ing the Slot Covers" (page 28). 2. Perform procedure "Remo v ing the Cam era" (this page).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 30 of 37 The following steps refer to Figure 3 4. 6. Access camera/lens board. To do this, loosen captive retaining screw holding bearing assembly in place and remove this assembly.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 31 of 37 6. Access tilt motor. To do this, loosen captive retaining screw holding tilt cable assembly in place and gently remove this assembly. 7. Remove tilt motor ( Figure 37).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 32 of 37 Parts List for Authorized Users The following parts can be orde red by authorized users only. To become authorized, cont act your sales representative.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 33 of 37 Figure 39. Base, housing, and eyeball assembly 33 27 28 29 30 31 32 45 44 43 42 41 34-40 Eyeball Assy.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 34 of 37 S pecifications-Indoor Dome Operational Pan/Tilt: Manual Pan S peed.................... 0.2°-100 ° per second (scaled to zoom position) Manual Tilt Speed .
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 35 of 37 Mechanical Height ......................................................... 20.8cm (8in) Eyeball Diameter .....................................
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 36 of 37 Declarations Regulatory Compliance REG ID ............................................................... VP SDU Emissions ....................
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 37 of 37 Appendix A: V icon Wiring Configurations In Vicon systems where domes sup port loop through, dai sy chain the SpeedDo me Ultra VII domes off the last Vicon dome in the communicatio ns chain.
Ein wichtiger Punkt beim Kauf des Geräts American Dynamics SpeedDome Ultra VII EIS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie American Dynamics SpeedDome Ultra VII EIS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für American Dynamics SpeedDome Ultra VII EIS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von American Dynamics SpeedDome Ultra VII EIS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über American Dynamics SpeedDome Ultra VII EIS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon American Dynamics SpeedDome Ultra VII EIS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von American Dynamics SpeedDome Ultra VII EIS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit American Dynamics SpeedDome Ultra VII EIS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei American Dynamics SpeedDome Ultra VII EIS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
