Benutzeranleitung / Produktwartung L20A09A des Produzenten Haier
Zur Seite of 26
USER'S MANUAL LCD TV RECEIVER Please read this manual carefully before using your television and keep this manual In a good place for future reference.
.
To users: Thank you for using our LCD-TV . Before connecting the LCD-TV and turning the power on, please read this book carefully . Please keep this book for later use. When it was loss of function by electrostatic shock, please switch the on/off button for restoring the function.
Safety Notice Items Incorrect usage will cause fire or electric shock. T o prevent this, please do as required when you are installing, using and cleaning this machine.
Front Panel Controls Control Panel Function 1. Power supply switch 2.TV/AV Select the input signals: SCART/PC/A V/SV/TV 3. MENU Press to select the main menu 4. VOL- Volume down / Left orientation to adjust the item in the OSD VOL+ V olume up / Right orientation to adjust the item/Press to enter 5.
AV Input Connect audio/video output from an external device to these jacks VGA Input Connect to the VGA 15PIN analog output connector of the PC display card for PC display purpose S-Video Input Connect S-Video out from an S-V ideo device to the jacks.
Remote Control Key Functions When using the remote control, aim it towards the remote sensor on the TV Stand By MUTE Display current input signal information TV channel number select Set time to change the TV into the standby status after a period of preset time.
Remote Control Installing Batteries 3 2 1 1.Slide open the cover of the battery compartment on the back of the remote control. 2.Load two 5# alkaline batteries in the compartment. (plus and minus poles to respective mark) 3.Replace the cover of the battery compartment.
Connection Instructions Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker . Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Connection Instructions You can use your LCD-TV as a monitor for your personal computer using a VGA cable (not supplied). PC Setup Connection and use steps: 1.Read the user guide supplied with your computer and ensure that it has a VGA connector; 2.Make sure that the power of the LCD -TV and the PC are of f; 3.
Connection Instructions VCR Setup Connection and use steps: 1.Read the user guide supplied with your A V devices and ensure that it has Composite or S-Video connectors; 2.Make sure that the power of the LCD-TV and the A V device are off; .Turn on the power of the LCD-TV first ; and then turn on the power of the A V device; 4.
Connection Instructions Cable TV Setup - Af ter subscribing to a cable TV service from a local provider you can watch cable TV programming. The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV.
Basic Operating Instructions Turn on the LCD-TV Switch on the power button on the back of the set and the TV will in s tandby mode. When the POWER button on the remote control is pressed and the LCD-TV is turned on, the indicator light on the front of the LCD-TV changes from red to green.
Basic Operating Instructions Select the TV Channel You Want You can use the number keys on the remote control to directly select TV channels. The LCD-TV can store up to 100 channels , and you can press the keys on the remote control or on the panel to make a selection.
Menu Operations Picture Menu Options 1. Press MENU button to display the main menu, and V+/V- to select the main menu . 2. Press P+/P- to scroll through the options 3.
Menu Operations 2. Press P+/P- button to enter the picture menu and to go up and down to select the desired option . 3.Press V+/V- button to increase and decrease the level to adjust the selected option to your preference . 4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Menu Operations Audio Menu Options continued You can adjust sound options to the levels you prefer. 2. Press P+/P- button to enter the audio menu and to go up and down to select the desired option . 3.Press V+/V- button to increase and decrease the level to adjust the selected option to your preference .
Menu Operations Function Menu Options Menu Language Selection : The menus can be shown on the screen in the selected language. First select your language. 1. 2. Press P+/P- button to select LANGUAGE. 3. Press V+/V- button to select your desired language.
Menu Operations Function Menu Options Continued 2. TXT LANGUAGE: T o switch the teletext languages. 3. TXT EAST/WEST : T o select EAST or WEST . 4.DISPLAY MODE: T o select the display mode between 4:3 and FULL SCREEN 5.BLUE SCREEN:T o set On, the screen will be in blue screen after 3 seconds if there is no signal.
Menu Operations Tuning Menu Options 1. Press MENU and V+/V- button until the following menu appears on the screen Note: This menu is only appears in TV mode . 2. Press P+/P- button to enter the tuning menu and to go up and down to select the desired option .
Menu Operations Tuning Menu Options Continued 7. EXCHANGE : Press V+ to display the menu as follows: Press P+/- to select the item and then V+/- to adjust the channel and V+ to confirm.
TELETEXT SIZE Button Press SIZE button to change display size : normal large top large bottom normal REVEAL Button Press REVEAL to reveal hidden words e.g. Quiz page answers . Press again to hide. Red/Green/ Yellow/Cyan Buttons These four buttons correspond to the differently colored subjects .
SUBCODE Button When T eletext information exceeds more than one page , it may take s ome time for the automatic changing of the sub pages to reach t he sub page you require . It is possible to enter your required sub page and continue watching the normal programme until the correct sub page is found .
T o assist in location possible faults use help guide below . Troubleshooting Guide Note: 1.If the fault can not be repaired using the above guide consult with your local authorized service center. 2.The TV set must only be repaired by a qualified registered service person.
Specifications Note: All specifications are subject to change without notice. All quality are approximate value. Specifications of the television that you have just purchased may vary from the information in this table due to technical innovations. Accessories Picture, sound system Audio output External input port Power requirements Temperature 1.
ENGLISH.
Ein wichtiger Punkt beim Kauf des Geräts Haier L20A09A (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Haier L20A09A noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Haier L20A09A - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Haier L20A09A reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Haier L20A09A erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Haier L20A09A besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Haier L20A09A verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Haier L20A09A. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Haier L20A09A gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
