Benutzeranleitung / Produktwartung 60 SERIES des Produzenten Hague Quality Water Intl
Zur Seite of 52
W W A A T T E E R R C C O O N N D D I I T T I I O O N N I I N N G G A A P P P P L L I I A A N N C C E E 6 6 0 0 S S E E R R I I E E S S O O W W N N E E R R ’ ’ S S M M A A N N U U A A L L A A N N D D I I N N S S T T A A L L L L A A T T I I O O N N G G U U I I D D E E V V E E R R S S I I O O N N 5 5 .
WaterMax 60 Series Owner’s Manual 11/10/2008 2 25 Y ear Limited W a rranty TO PLACE THIS EQUIPMENT UNDER WA RRANTY, THE WARRANTY REGISTRATION CARD MUST BE COMPLETE D AND RETURNED BY THE ORIGINAL OWNER TO HAGUE QUALITY WATER INTERNATIONAL WITHIN 30 DAYS OF INSTALLATION.
WaterMax 60 Series Owner’s Manual 11/10/2008 3 Content s OWNER INFO RMATION .............................................................................................................. ........................ 4 General Information ...............
WaterMax 60 Series Owner’s Manual 11/10/2008 4 General Information Congratulations on choosing a superior Hague water treatment appliance! Soon you and your family will be enjoying clean, clear water. Use this guide to attain the maximum benefit from your appliance.
WaterMax 60 Series Owner’s Manual 11/10/2008 5 Getting Maximum Efficiency From the Appliance To achieve the maximum benefit and performance from this appliance, familiarize yourself with this manual and the appliance. 1. The salt level should always be at least 1/3 full.
WaterMax 60 Series Owner’s Manual 11/10/2008 6 Six-Button Controller , Cont. Controller Part Function LCD Display Shows the status of the controller Normal Operating Mode Shows x The amount of soft .
WaterMax 60 Series Owner’s Manual 11/10/2008 7 Customer Settings Service Settings must be set before Customer Settings; Service Settings should be set during installation of the appliance. To set Customer Settings, press and hold the Customer Settings button for about three seconds while “Customer Setting” displays.
WaterMax 60 Series Owner’s Manual 11/10/2008 8 Checklist Before Inst allation Refer to this checklist before each installation. Water Quality —If the water supply contains sand, sulfur, bacter.
WaterMax 60 Series Owner’s Manual 11/10/2008 9 Precautions Do 1. Comply with all state and local, building, plumbing, and electrical codes. 2. Install the appliance before the water heater. 3. Install the appliance after the pressure tank on well-water installations.
WaterMax 60 Series Owner’s Manual 11/10/2008 10 Inst allation Step s and St art-Up Procedures Step 1 Prepare the Placement Area A. Make sure the placement area is clean. B. Turn off the electricity and water supply to the water heater. For gas water heaters, turn the gas cock to “Pilot.
WaterMax 60 Series Owner’s Manual 11/10/2008 11 Inst allation Step s and St art-Up Procedures, Cont. Step 2 Turn Off Wate r Supply A. Turn off the water supply. B. Open the hot and cold water taps to depressurize the lines. Step 3 Connect Water Lines A.
WaterMax 60 Series Owner’s Manual 11/10/2008 12 Inst allation Step s and St art-Up Procedures, Cont. Step 8 Check for Leaks A. Close all faucets. B. Check all lines and connections for leaks. If leaks are found: 1. Turn off the main water supply. 2.
WaterMax 60 Series Owner’s Manual 11/10/2008 13 Inst allation Step s and St art-Up Procedures, Cont. Step 13 Complete the Installation A. Open the inlet valve and turn on the electricity to the water heater. For gas water heaters, return the gas cock to “On.
WaterMax 60 Series Owner’s Manual 11/10/2008 14 Blending V alve In some situations, the blending valve may be used to decrease water softness. The amount of hardness blended back into the water line is determined by the hardness of the incoming water and the setting of the blending valve.
WaterMax 60 Series Owner’s Manual 11/10/2008 15 Service Settings To program Service settings on the 60 Series controller, press and hold the Service Settings button while “Service Settings” is displayed until “Set Language English” is displayed.
WaterMax 60 Series Owner’s Manual 11/10/2008 16 Service Settings, Cont. Display Meaning Possible Values Comments Total Regens 00000 Total number of r egenerations since Service Settings was last ent.
WaterMax 60 Series Owner’s Manual 11/10/2008 17 Service Settings, Cont. Display Meaning Possible Values Comments 72–96 Hour Regeneration No A way to force regeneration at regularly-scheduled intervals No (or Yes, for iron) See 72–96 Hour Regeneration that follows.
WaterMax 60 Series Owner’s Manual 11/10/2008 18 Service Settings, Cont. Operating Modes The controller has a Timer mode (Mode 1 Frequency and Mode 1 Days of the Week), a Demand Delayed mode (Mode 2), and a Demand Immediate mode (Mode 3).
WaterMax 60 Series Owner’s Manual 11/10/2008 19 Service Settings, Cont. Mode 1 (Timer Mode) Setting Chart This section provides guidance for using different service settings to achieve the desired capacity.
WaterMax 60 Series Owner’s Manual 11/10/2008 20 Service Settings, Cont. Mode 2 (Demand Delayed Mode) Setting Chart This section provides guidance for using different service settings to achieve the desired capacity. Note: Mode 2 and Mode 3 have the same settings.
WaterMax 60 Series Owner’s Manual 11/10/2008 21 Salt Depths Based on the water level measured from the bottom of the brine cabinet with grid plate, the following depths correlate to the amount of salt used per regeneration: Modes 1 and 3 Mode 2 Salt (lb) Depth (in.
WaterMax 60 Series Owner’s Manual 11/10/2008 22 62AJQ Replenishment Procedure The neutralizing media that adjusts the pH level of the water must be refilled periodically. Typically, this media is calcite and is available from Hague. To refill the neutralizing media, measure the appliance’s media bed depth upon installation (factory freeboard).
WaterMax 60 Series Owner’s Manual 11/10/2008 23 62AJQ Replenishment Procedure, Cont. Step 4 Add Replenishment Media A. Weigh the replenishment media. B. Place the funnel into the fill port. C. Pour the media into the funnel to fill the tank with the measured amount of media.
WaterMax 60 Series Owner’s Manual 11/10/2008 24 61AAN W aterMax ® Iron Filter Sizing Formula The WaterMax ® Iron Filter may be programmed to regenerate every one to twelve days. Select the frequency based on the amount of iron in the water and the number of people in the household.
WaterMax 60 Series Owner’s Manual 11/10/2008 25 Iron Filter and Pot assium Feeder Installation Guide Important: The 61AAN is capable of treating a combination of undesirable constituents in the water (iron, manganese, and/or hydrogen sulfide).
WaterMax 60 Series Owner’s Manual 11/10/2008 26 S t art-Up Procedures for 4-oz Potassium Permanganate Feeder Step 1 Unpack Feeder A. Remove feeder from shipping carton. B. Read the instructions in red, remove the label from the feeder, and discard it into the shipping carton.
WaterMax 60 Series Owner’s Manual 11/10/2008 27 Assembly and Part s Cabinet and Cover Assemblies Figure 7: Cabinet and Cover Assemblies Figure 8: Controller Tab Lock Detail Part # Description Quanti.
WaterMax 60 Series Owner’s Manual 11/10/2008 28 Assembly and Part s, Cont. Brine Tank Assembly Figure 9: Brine Tank Assembly Figure 10: Potassium Permanganate Feeder (P/N PT1424) Part # Description .
WaterMax 60 Series Owner’s Manual 11/10/2008 29 Assembly and Part s, Cont. Cabinet and Assemblies Figure 11: Cabinet and Assemblies Part # Description Quantity 1 93809 Screw 2 2 93870 Screw 4 3 9061.
WaterMax 60 Series Owner’s Manual 11/10/2008 30 Assembly and Part s, Cont. Injector Assembly Figure 12: Injector Assembly Part # Description Quantity 1 93810 Injector Screen 1 2 93223 Injector Throa.
WaterMax 60 Series Owner’s Manual 11/10/2008 31 Assembly and Part s, Cont. Injector Assembly Cont. 93810 Injector Screen Acts as a pre-filter to keep debris from entering the Inject or Nozzle (932 21) and Thr oat (93223). Attaches to the cylinder on the Nozzle plate and spheri cal “bump” inside the Valve Body.
WaterMax 60 Series Owner’s Manual 11/10/2008 32 Assembly and Part s, Cont. Bypass Assembly Figure 13: Bypass Assembly Part # Description Quantity 1 90807 Screw 12 2 90262 Bypass End cap-Left 1 3 938.
WaterMax 60 Series Owner’s Manual 11/10/2008 33 Assembly and Part s, Cont. Bypass Assembly Cont. 90262 By pass End Cap—Left; 90263 By pass End Cap—Right Seals the left/right Piston opening on the Housing (90246). The opening is sealed with an O-Ring used as an axial or “face” seal .
WaterMax 60 Series Owner’s Manual 11/10/2008 34 Assembly and Part s, Cont. Drive End Cap Assembly Figure 14: Drive End Cap Assembly Part # Description Quantity 1 90802 Screw 2 2 90217 Drive Motor 1 .
WaterMax 60 Series Owner’s Manual 11/10/2008 35 Assembly and Part s, Cont. Drive End Cap Assembly Cont. 90217 Drive Motor The Motor is held in place by two 1/2" screws. The scr ews should be “s nug.” T he brass pinion gear on the Motor should engage the plastic Drive Gear.
WaterMax 60 Series Owner’s Manual 11/10/2008 36 Assembly and Part s, Cont. Brine Valve Housing Assembly Figure 15: Brine Valve Housing Assembly Part # Description Quantity 1 53511 Piston Assembly (incl udes O- Ring & Spring) 1 2 90821 O-Ri ng 1 3 53510 Housi ng 1 4 90843 0.
WaterMax 60 Series Owner’s Manual 11/10/2008 37 Assembly and Part s, Cont. Brine Valve Housing Assembly Cont. 53511 Brine Piston The Piston should have an O-Ring on the shaft side of the fl ange and a spring pressed onto a boss on the other side. The O-Ring sh ou ld be free of defects such as cuts or debris on the shaft side.
WaterMax 60 Series Owner’s Manual 11/10/2008 38 Assembly and Part s, Cont. Drain End Cap Assembly Figure 16: Drain End Cap Assembly Part # Description Quantity 1 93808 O-Ring 1 2 90268 Drain End Cap.
WaterMax 60 Series Owner’s Manual 11/10/2008 39 Assembly and Part s, Cont. Safety Shutoff Assembly Figure 17: Safety Shutoff Assembly Part # Description Quantity 1 54226 Safety S hutoff (See Figure .
WaterMax 60 Series Owner’s Manual 11/10/2008 40 Assembly and Part s, Cont. Safety Shutoff Valve Elbow Installation Figure 18: Safety Shutoff Valve Elbow Installation Part # Description Quantity 1 54.
WaterMax 60 Series Owner’s Manual 11/10/2008 41 Assembly and Part s, Cont. Fill Plug Assembly Figure 19: Fill Plug Assembly Part # Description Quantity 1 90238 Fill Plug 1 2 90829 Fill Plug O-Ring Seal 1 90618 Fill Plug Ass embly (all of the above parts) 90238 Fill Plug The Fill Plug (90238) seals the media access ports in the Media T ank.
WaterMax 60 Series Owner’s Manual 11/10/2008 42 T roubleshooting Problem Possible Cause Solution No salt in brine cabinet Add salt Sediment in brine tank has plugged t he brine line and air check/draw tube Remove air check/draw tube and flush with clean water.
WaterMax 60 Series Owner’s Manual 11/10/2008 43 T roubleshooting, Cont. Problem Possible Cause Solution Controller not attached properly Make sure the controller is pushed all the way onto the drive.
WaterMax 60 Series Owner’s Manual 11/10/2008 44 Reading Model Numbers Hague appliance model numbers typically consist of two numerals followed by three letters, such as the WaterMax ® 63BEQ.
WaterMax 60 Series Owner’s Manual 11/10/2008 45 W aterMax ® W ater Conditioner S pecifications 60 Series 63M AQ 1 63BEQ 1,2 63MXQ 1 63M DQ 62AMQ 1 62APQ 1 62AKQ 62AJQ 3 Max Compensated Hardness (gp.
WaterMax 60 Series Owner’s Manual 11/10/2008 46 W aterMax ® Filter S pecifications The following table describes the available filters. Filter Purpose 61AAN Removes ir on and ir on al gae and bacteria. Reduces manganese. Als o removes up to 5 ppm Hydrogen Sulfide with the presence of 2 ppm iron.
WaterMax 60 Series Owner’s Manual 11/10/2008 47 Certificates.
WaterMax 60 Series Owner’s Manual 11/10/2008 48 Certificates, Cont..
WaterMax 60 Series Owner’s Manual 11/10/2008 49 Certificates, Cont..
Notes.
Notes.
LITHO USA ©2008 F54015 RV1008TL 60 Series has these third-party listings: The WQA Gold Seal assures that this product has been tested and validated by the Water Quali ty Association. This validation assures that all electrical components are UL or CSA lis ted and all compo nents that are in contact with the treate d water are FDA or NSF listed.
Ein wichtiger Punkt beim Kauf des Geräts Hague Quality Water Intl 60 SERIES (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hague Quality Water Intl 60 SERIES noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hague Quality Water Intl 60 SERIES - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hague Quality Water Intl 60 SERIES reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hague Quality Water Intl 60 SERIES erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hague Quality Water Intl 60 SERIES besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hague Quality Water Intl 60 SERIES verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hague Quality Water Intl 60 SERIES. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hague Quality Water Intl 60 SERIES gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
