Benutzeranleitung / Produktwartung GEM-RP8 des Produzenten Gemini
Zur Seite of 16
ARME D COM PUT ERI ZED SE CURI TY SY STE M STAT US I H 1 2 3 4 5 6 7 8 A 1 2 3 B 4 5 6 C 7 8 9 0 E F G J OPERA TING GUIDE for your GEM-RP8 KEYP AD © NAPCO 2003 DESIGN PATS.
Congratulations on your p urchase of an advanced GEMINI-RP8 keyp ad. Meticulously deve loped by a leading manufacturer of state-of-the-art security products, this sy stem will provide y ou with unprecedented peace-of -mind & incorporates some of the most sophisticated features availab le to day.
3 Important - T est Y our System W eekly! 1 Bell / Batter y Test Test your bell or siren by pressin g A follow ed b y 1 . This will cause the be ll, or siren to s ound for 2 seconds and also initiate a test of the bat tery. 2 Zone Test W alk throughout the premises, opening each protected door or window, and act ivating each motion sens or.
ARME D COM PUT ERI ZED SE CURI TY SY STE M STAT US I H GEMIN I 1 2 3 4 5 6 7 8 A 1 2 3 B 4 5 6 C 7 8 9 0 E F G J 4 Statu s Ligh t will lig ht whe n all zo nes are secure and sy stem is rea dy to be Armed. AC Light will light to indicate that AC Power is present.
Arming Your System When Leaving 1 Before arming y our system, make sure the green Status light is ON. T his indicates that all of your prote ctive zones are secure. If any zones are open, the corresponding Zone number will be lit. Secure these zones before proceeding.
Protecting Yourself While at Home 1 Before arming y our system, make sure the green Status light is ON. T his indicates that all of your protective zones a re secure. If any zones are open, the co rresponding zone nu mber will be lit. Secure those zones before proceeding.
Emergency Butt ons 7 8 9 G The three sets of emergen cy buttons, if programmed , are alw ays active whether the sy stem is arm ed or disarmed. Discuss these Buttons with your insta ller. The emergency signal w ill only be activate d when the two respective buttons are pressed at the same time.
Disarming Your System when Return ing 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone t o remind you to disarm the system bef ore y our Entry Delay tim e expi res. 2 Ent er your User Co de and press D . The red Ar m e d light will go out, indicating that the system has been disarmed.
Preparing a Fire Escape Plan Eve n with the most advanced f ire alarm system, adequate protection requ ires an escape plan. To prepare your pla n, draw floor plans of yo ur building (space is provided on the next page ). Show two exits-a front or back door and a window from each room.
10 Floorplan Draw a plan of yo ur premises below. FIRE PROTECTION.
By pressing A followed by the the appropriate key, (do not press simultaneously ) these special functions and features can be enabled: Easy Arm (when s ystem is di sarmed) The Easy Arm feature a llows the system to be armed by pressing A followed b y 0 .
12 The Control Panel is constantl y monitoring its own components, as well as all critical servic es, such as AC po wer and the telephone line, to insure that it is al ways read y to pro vide the protectio n for which it was designed.
13 Keypad Beeps or H Flashes Zone light ON System T rouble Condition Action 2 Beeps 2 Fire Trouble A problem has been detecte d in the Fire C ircuit. Call installi ng company for service. 2 Beeps 3 Wir el e s s R ec ei v e r Trouble A problem has been detected with the wireless receiver.
Your Installer has assigned a User 1 Code wh ich can be used to not only Arm and Disarm the sy stem, but also to enter the User Program Mode, whe re you can program other user codes. T he following explains how you w ill use this code to program or erase additional user codes.
Ambush Code - In the event that you are forced by an intruder to disarm your system, this special code can be used to disarm the s ystem, and simultaneously send a silent alarm to Central Station. If your sy stem has the Ambush feature enabled, the code assigned as the User 8 code will function as your Ambush Code.
NAPCO LIMITED W A RRANTY THE F OLLOWING STATEMENT IS REQ UIRED BY TH E FCC . This equipmen t generates and uses radio-freq uency energy an d, if not installed and used pr operly, that is, in strict accordance with th e manufacturer's instructions, may cau se interference to radio and tel e visi o n reception.
Ein wichtiger Punkt beim Kauf des Geräts Gemini GEM-RP8 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Gemini GEM-RP8 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Gemini GEM-RP8 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Gemini GEM-RP8 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Gemini GEM-RP8 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Gemini GEM-RP8 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Gemini GEM-RP8 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Gemini GEM-RP8. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Gemini GEM-RP8 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.