Benutzeranleitung / Produktwartung ZBD5700 des Produzenten GE
Zur Seite of 24
GE Monogram ® Installation Instr uctions with Optional T rim Kit Installation Instr uctions Built-In Dishwashers Models ZBD5600 ZBD5700 ZBD5900.
2 Before you begin - Read these instructions completely and carefully. IMPORTANT - Save these instructions for local inspector’s use. IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer - Be sure to leave these instructions with the Consumer.
3 Design Information Stainless Steel Interior Dishwashers Models Available ZBD5600 WW , ZBD5700 WW White Dishwashers ZBD5600 BB, ZBD5700 BB Black Dishwashers ZBD5900 SS Stainless Steel Dishwasher These dishwashers ar e designed for versatility , adaptable to virtually any installation.
4 Design Information Stainless Steel Interior Dishwashers Standard installation in 24” deep cabinets • Install in standard 24” deep cabinets: – The dishwasher door will be flush with the fr ont face of adjacent cabinetr y . • With a 3/4” thick custom door panel in place, the exterior is trimless and fits flush to adjacent cabinetr y .
5 Installation Infor mation Stainless Steel Interior Dishwashers Par ts Supplied Remove the hardware accessor y bag and other parts from inside or taped to the outside of the dishwasher . Check contents against drawings to insure that all par ts ar e included.
6 Installation Preparation Stainless Steel Interior Dishwasher Materials Y ou W ill Need: (not supplied) ■ ■ 90 ° elbow (3/8" NPT external thread on one end and opposite end to fit hot water.
7 Installation Preparation Stainless Steel Interior Dishwasher • The rough cabinet opening must be 24” min. deep, 23-5/8” min. to 24” max. wide. The opening height should be 34” min. and 35” max. • The opening should be fr ee of extraneous pipes and wires.
8 Installation Preparation Stainless Steel Interior Dishwashers Electrical Requir ements: These dishwashers must be supplied with a 120 volt, 60 Hz power supply with an indi- vidual, properly gr ounded branch circuit, protected by a 15 or 20 amp fuse or cir cuit breaker or time delay fuse.
9 Installation Preparation Stainless Steel Interior Dishwasher Prepare drain plumbing • Follow local codes and ordinances. • Dishwasher drain hose must not exceed 10 feet in length for proper drainage. – The dishwasher is supplied with a 3/4” I.
10 Installation Stainless Steel Interior Dishwasher Install Custom Door Panel • If you intend to install custom door panels, refer to installation instr uctions provided in this booklet. The panels should be in place before installing the dishwasher .
11 Installation Stainless Steel Interior Dishwasher Step 3 Install W ater Inlet Fittings Step 4 Install power cord (If used) Skip this step If dishwasher will be wired direct. • Install the 90 ° elbow onto the water inlet. Use thread sealing tape or pipe thread compound.
12 Installation Stainless Steel Interior Dishwasher Step 5 Level the Dishwasher Step 6 Slide Dishwasher Into Opening • Carefully upright the dishwasher , taking care not to bend the leveling legs. Make sure the leveling leg locking nuts are secure. • Check to be sure the dishwasher is level and at the cutout height.
13 Installation Stainless Steel Interior Dishwasher • Follow all local codes and ordinances. Drain Line Pr eparation • The dishwasher is supplied with a 78” long corr ugated drain hose. • If the location requir es a longer drain hose, add up to 42” length to the supplied hose.
14 Installation Stainless Steel Interior Dishwasher Step 10 Secure Dishwasher to Counter top or Cabinetr y T o maintain position and alignment the dishwasher must be secur ed to the counter top or to adjacent cabinetr y . If countertop is of stone or other hard material, secure the dishwasher to adjacent cabinets.
15 Installation Stainless Steel Interior Dishwasher • Install toekick slides to toekick support brackets. Use slide stamped “L” on left and “R” on right side. • Align front and inner toekicks, matching screw holes. • Align toekick to second screw hole in toekick slide as illustrated.
16 ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel • Cut door panel to the dimensions shown. • The bottom left and right corners should be cut at 1/4” radius. See illustration. Note: The trim will conceal the cut edges of the panels.
17 ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel • Place the supplied metal door on a flat sur face. • Place the custom panel on top of the metal door . • Place supplied trim over the custom panel. • Press trim to panel and install the color matched screws provided.
18 ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel The additional weight of the custom panel may require that the heavy door springs be installed. T est Door Balance • With one hand under the door , slowly open the door fully . • Open and close the door to check for proper balance.
19 ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel ZPF75B, Black ZPF75W , White Tools and Materials required • Phillips screwdriver • Gloves to protect against sharp edges • Nut driver Step 1: Deter mine Custom Panel Sizes The custom panel should be constr ucted in the same manner as cabinet doors.
20 ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel Step 2 Remove Existing Metal Door • Open the door fully . Caution: One person should hold the door while the other backs out screws to prevent the metal door from falling. • Remove 6 screws on the inside of the frame.
21 ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel Step 5 Install Assembled Door onto Dishwasher Note: One person should hold the door while the other installs screws to prevent the door assembly from falling. • Check to be sure that foam inserts are in place.
22 ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel Step 7 Install Custom T oekick • Slip toekick slides into guides by pulling out the metal tabs. • Hold custom panel against toekick slides and mark screw hole locations. • Remove toekick and drill 1/8" pilot holes.
23 Notes Stainless Steel Interior Dishwasher.
Pub. No. 49-5860-1 Printed in USA 1999 GE Appliances (N.D. 458) 9/99 Part Number: C82 0017x Issue A NOTE: While performing installations described in this book, safety glasses or goggles should be worn. T o obtain specific information concer ning any Monogram pr oduct or ser vice, call GE Answer Center ® consumer information ser vice at 800.
Ein wichtiger Punkt beim Kauf des Geräts GE ZBD5700 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie GE ZBD5700 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für GE ZBD5700 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von GE ZBD5700 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über GE ZBD5700 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon GE ZBD5700 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von GE ZBD5700 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit GE ZBD5700. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei GE ZBD5700 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
