Benutzeranleitung / Produktwartung COMBITHERM COMBINATION Oven / Steamer ES electric combitouch des Produzenten Alto-Shaam
Zur Seite of 41
MN-29245 • 05/12 printed i n u . s . a . Combitherm ® Combination Oven / Steamer ES ELECTRIC COMBITOUCH® SERIES 6•10 10•10 7•14 10•18 12•20 20•20 VHes-5 VHes -10 • InstallatIon W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA PHONE: 262.
i Delivery .................................. 1 Unpacking ................................ 1 Safety Procedures and Precautions ............. 2 Installation Site Requirements ........................ 3 Ventilation Requirements ................... 3 Positioning on Site .
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 1. DELIVERY This Alto-Shaam appliance has been thoroughly tested and inspected to ensure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier.
CAUTION Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 3. SITE INSTALLATION INSTALLATION DANGER IMPROPER INSTALLATION, ALTERATION, ADJUSTMENT, SERVICE, OR MAINTENANCE COULD RESULT IN SEVERE INJURY, DEATH, OR CAUSE PROPERTY DAMAGE.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 4. NOTE: Note dimensions required for doorways and aisles for access of the oven and pallet to the installation site. Transport the oven in an upright and level position only. Do not tilt the oven.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 5. SITE INSTALLATION INSTALLATION Lifting Ins tructions Do not lift in this area! Damage t o the components will r esult. Cent er of Gra vity Front View T op View (Fron t) Leg 24” Spacer Board Remov e banding befor e lifting.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 6. SITE INSTALLATION INSTALLATION POSITIONING REQUIREMENTS q In order to ensure proper ventilation, a minimum distance of at least 6-inches (152mm) must be kept from the control panels side (left) of the oven and any adjoining surfaces.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 7. COMMON SPECIFICATIONS CombiGuard™ BWS Blended Water System ( iNcludEs 50 gallON taNk , 1 MEMbraNE & 3 FiltErs ) FI-28727 CombiGuard.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 8. 6•10 es 31-3/8" (796mm) 34-1/16" (864mm) 17-15/16" (456mm) 7-9/16" (191mm) WA TER DRAIN 33-1/8" (840mm) 4-15/1.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 9. 6•10 es i 31-3/8" (796mm) 34-1/16" (864mm) 17-15/16" (456mm) 7-9/16" (191mm) WA TER DRAIN 33-1/8" (840mm) 4-15.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 10. 6•10 es iN 32-15/16" (835mm) 35-9/16" (903mm) 21-11/16" (550mm) 5-3/8" (137mm) 6-3/8" (161mm) WA TER DRAIN 33.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 11. 10•10 es 33-1/16" (840mm) 4-15/16" (125mm) 41-1/2" (1053mm) 33-15/16" (861mm) 7-9/16" (192mm) 60-9/16" (.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 12. 10•10 es i 33-1/16" (840mm) 4-15/16" (125mm) 41-1/2" (1053mm) 33-15/16" (861mm) 7-9/16" (192mm) 60-9/16".
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 13. 19-1/2" (495mm) 12-5/16" (312mm) 9-9/16" ( 242m m) 35-7/8" (910mm) 33-7/8" (860mm) 33" (837mm) 2" (50.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 14. 7•14 es TO P VIEW FRONT VIEW SIDE VIEW A rial MT Condensed Light 8 pt 43-3/4" (1111mm) 8-1/2" (216mm) 26-1/2" (672mm) 6.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 15. 7•14 es i TO P VIEW FRONT VIEW SIDE VIEW A rial MT Condensed Light 8 pt 43-3/4" (1111mm) 8-1/2" (216mm) 26-1/2" (672mm).
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 16. 30" (760mm) 22-3/8" (568mm) 15-1/2" (393mm) 12-3/4" (323mm) Electrical Connection (Bottom) 2" (50mm) 46-7/8&quo.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 17. 10•18 es i WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS TWO (2) COLD W A TER INLETS - DRINKING QUALITY ONE (1) TREA TED W A TER INLET : 3/4" NPT* ONE (1) UNTREA TED W A TER INLET : 3/4" NPT* LI NE PR ES SU RE : 30 to 90 psi 2.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 18. 46-3/4" (1186mm) 44-3/4" (1136mm) 40-15/16" (1039mm) 1-13/16" (46mm) 48" (1218mm) 45-5/16" (1151mm) 33-1/2.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 19. 12•20 es i WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS TWO (2) COLD W A TER INLETS - DRINKING QUALITY ONE (1) TREA TED W A TER INLET : 3/4" NPT* ONE (1) UNTREA TED W A TER INLET : 3/4" NPT* LI NE PR ES SU RE : 30 to 90 psi 2.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 20. 40-15/16" (1039mm) 1-13/16" (46mm) 46-3/4" (1186mm) 44-3/4" (1136mm) 4-3/4" (120mm) 2" (50mm) 51-15/16&quo.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 21. 20•20 es i WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS TWO (2) COLD W A TER INLETS - DRINKING QUALITY ONE (1) TREA TED W A TER INLET : 3/4" NPT* ONE (1) UNTREA TED W A TER INLET : 3/4" NPT* LI NE PR ES SU RE : 30 to 90 psi 2.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 22. ELECTRICAL CONNECTION INSTALLATION DANGER ENSURE POWER SOURCE MATCHES VOLTAGE IDENTIFIED ON APPLIANCE RATING TAG.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 23. ELECTRICAL CONNECTION INSTALLATION DANGER ELECTRICAL CONNECTIONS MUST BE MADE BY A QUALIFIED SERVICE TECHNICIAN IN ACCORDANCE WITH APPLICABLE ELECTRICAL CODES.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 24. MOBILE EQUIPMENT RESTRAINT INSTALLATION Any appliance that is not furnished with a power supply cord but includes a set of casters must be installed with a tether.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 25. INSTALLATION WATER QUALITY REQUIREMENT WARNING TO PREVENT WATER PIPES OR HOSES FROM BURSTING, INCOMING WATER SUPPLY SHOULD BE TURNED OFF WHEN THE APPLIANCE IS NOT IN USE. WARNING WATER SUPPLY MUST BE OPEN WHEN CLEANING PROGRAM IS ACTIVATED.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 26. INSTALLATION WATER CONNECTIONS WATER SUPPLY & INSTALLATION WATER REQUIREMENTS TWO (2) COLD WATER INLETS - DRINKING QUALITY ONE (1) TREATED WATER INLET: 3/4" NPT* ONE (1) UNTREATED WATER INLET: 3/4" NPT* LINE PRESSURE: 30 to 90 psi 2.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 27. INSTALLATION WATER VALVE WATER DRAINAGE shut - off valve shown i n the off position NOTE: THE SHUT-OFF VALVE MUST BE IN THE OPEN POSITION WHEN THE OVEN IS BEING USED. The oven must discharge through an indirect waste pipe by means of an air gap.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 28. GREASE COLLECTION HOOK-UP ( I F EQUIPPED WITH THIS FEATURE ) • Grease Collection Hose Assembly is attached to the oven in the back. • Place Grease Collection Containers inside the tray of the Mobile Grease Collection Cart.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 29. INSTALLATION COMBITOUCH® CHECKLIST Use this list as a nal check of oven installation conformance. Damage directly attributed to improper set up, installation, or cleaning can invalidate warranty claims.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 30. INSTALLATION cONTINUed ON NexT pAge ERROR CODES This section is provided for the assistance of qualified technicians only and is not intended for use by untrained or unauthorized service personnel.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 31. INSTALLATION cONTINUed ON NexT pAge ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E13 Boiler Temperature High Boiler temperature overheats — Scale build up inside steam generator.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 32. INSTALLATION ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E34 Steam Generator Drain Pump Fault Water level in steam generator does not drop during cleaning program — Scale build up inside the steam generator drain pump.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 33. INSTALLATION ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E57 No Rinse Water During rinse no water fl ow is detected through solenoid valve — Water supply is shut off.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 34. INSTALLATION Type of Error Indication Release of Error Undervoltage LED fl ashing sequence, with 1 fl ash per period. Voltage of intermediate circuit is less than 250V Overvoltage LED fl ashing sequence, with 2 fl ashes per period.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 35. INSTALLATION ERROR CODES When the oven malfunctions, an error code will appear in the display . PRESS THE ST AR T ICON TO ACKNOWLEDGE THE ERROR. The icons that begin to flash repr esent operational modes that are still usable.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 36. INSTALLATION VENTLESS HOOD OPTION The Ventless Hood option is factory installed directly on the top of the Alto-Shaam Combitherm oven. The hood is designed to vent clean air back into the kitchen, filtering vapors and grease.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 37. INSTALLATION VENTLESS HOOD OPTION TOP LEVEL ASSY, VHES-5 HOOD FOR COMBI 5010692 TOP EXHAUST VENT 2 6 1 4 3 5 7 1 Ventless Hood Power Knob 2 Emergency Latch Release: This release is to be used ONLY if the timed latch mechanism is not working or in the event of a power outage.
COMBITOUCH® ES SERIES • ELECTRIC INSTALLATION MANUAL • 38. ORIGINAL EQUIPMENT LIMITED WARRANTY Alto-Shaam, Inc. warrants to the original purchaser that any original part that is found to be defective in material or workmanship will, at Alto-Shaam’s option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part.
TRANSPORTATION DAMAGE AND CLAIMS All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee.
Ein wichtiger Punkt beim Kauf des Geräts Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Alto-Shaam COMBITHERM COMBINATION Oven / Steamer ES electric combitouch gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
