Benutzeranleitung / Produktwartung 840 VT-100 des Produzenten Gateway
Zur Seite of 250
Gatewa y 840 VT-100 User's Guide Installing Getting Help.
i Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii 5 SAN LUN Map ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 9 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Terminology .
iii 9 Event Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Accessing e vent logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4 Contro ller events .
iv.
1 1 Intr oduction This guide provides the operational and reference informati on to configure and ma nage the RAID controll ers installed in your Gateway 840 Series storage system. The controllers a re accessed through a VT -100 te rminal using a menu-based user interface, connected directly to the RAID controllers.
2 Chapter 1: Introduction www .gate wa y .com Features Y our Gateway 840 ha s a menu-based software utility designed to c onfigure and manage the RAID controller in your new storage enclosure.
3 Troub leshooting a ssistan ce www .gate wa y .com T r oub leshooting assistance T o help troubleshoot problems with your system, the Event Logs chapter , as well as on-line help, provides a list of all the events that can occur , along with a suggested cause and actio n to take.
4 Chapter 1: Introduction www .gate wa y .com.
2 5 Accessing the Configuration Utility Thi s cha pte r pro vid es in for mat ion on acc ess ing t he configuration ut ility . R ead th is chapter to learn how to: ■ Access the utility ■ Use the V.
6 Chapte r 2: Access ing the Con figuration Uti lity www .gate wa y .com Accessing the utility Y ou can acc ess the SA T A RAID con troller by using a VT -100 terminal co nnected to the RS-232 se rial ports on the controller’ s rear pa nel. Configure your terminal using the procedures desc ribed in “U sing the VT -100 terminal” on page 7 .
7 Using the V T-100 termi nal www .gate wa y .com Using the VT -100 terminal Access to the RAID cont roller is accomplished by using its onboard configuration uti lity with a VT -100 terminal or terminal emulation connect e d to the RS- 232 serial port on the controlle r .
8 Chapte r 2: Access ing the Con figuration Uti lity www .gate wa y .com 3 From the computer o r terminal connected to the RAID c ontroller , start your terminal emulation software. 4 From the terminal window , press C TRL + W . T he Main M enu op ens.
9 Navigatin g the SATA RA ID configu ration utili ty www .gate wa y .com Na vigating the SA T A RAID configur ation utilit y The SA T A R AID configuration utility menu system can be navigated using the keys on your keyboard. The table below describes the primary navigation and selection methods.
10 Chapte r 2: Access ing the Con figuration Uti lity www .gate wa y .com Menu system Main Menu Configuration Menu Controller Information Statistics Event Logs Diagnostics Enclosure Information Config.
11 Navigatin g the SATA RA ID configu ration utili ty www .gate wa y .com Menu system (co ntinued) RS232 Setting 115200 57600 38400 19200 9600 Port ID Selection View Arra y Create Array Delete Array E.
12 Chapte r 2: Access ing the Con figuration Uti lity www .gate wa y .com Menu system (co ntinued) Displays Controller P arameters Select Logical Drive View Access Statistics on P or t 0 View Access S.
13 Viewing c ontroll er informat ion www .gate wa y .com Vie wing contr oller inf ormation Detailed informati o n on the RAID controller is available through t he Main Menu, and includes: ■ C o n t .
14 Chapte r 2: Access ing the Con figuration Uti lity www .gate wa y .com 2 From the Main Menu select Controller Inf ormation, then press E NTER . The Contro ller Information screen opens. 3 Select the controller you want to examine by usi ng the spacebar to select the controller , then p ress E NTER .
15 Viewing c ontroll er informat ion www .gate wa y .com Firmware Re vision The firmware version i n use by t he controller . Firmw are Date/Time Date and t ime of when the fi r mw are was crea ted. T o tal P ower on Cou nt The num ber of times this c ontroller has bee n powe r cycled.
16 Chapte r 2: Access ing the Con figuration Uti lity www .gate wa y .com.
3 17 Creating Disk Arra ys This chapter provides informa tion on creating disk arrays. Read thi s chapter to le arn how to: ■ Understand arrays ■ Create arrays ■ Configure array read-ahea d and .
18 Chapter 3: Cre ating Disk Arrays www .gate wa y .com Over vie w Configuring a RAID system requires some planning to ma ke sure that you def ine the correct RAID le vels and array option s. It may be help ful to refer to the T opology chapter in the Gateway 840 SA T A RAID Enclosure Use r’ s Guide .
19 Understandi ng arrays www .gate wa y .com Under standing arra ys Y ou can crea te an array at an y time. The table below desc ribes the drive requirements for each R AID level. T erminology The following describes th e terminology used when creating and managing arrays.
20 Chapter 3: Cre ating Disk Arrays www .gate wa y .com Initiali zation RAID 5/ 50 arra ys mu st hav e cons istent parity before they can be u sed to prot ect data.
21 Understandi ng arrays www .gate wa y .com Optimization and drive selection for RAID 5 arrays T ypical RAID 5 implementations require a number of ste ps to write the data to the drives.
22 Chapter 3: Cre ating Disk Arrays www .gate wa y .com Creating arra ys Configuring th e arrays involves a few basic steps. All configurati o n pa rameters are stored on all hard drives that are members of the specific array . Th is makes it possible to remove and replace controllers without requiring any configuration changes.
23 Cr eating arrays www .gate wa y .com T o view an array: 1 From the Main Menu, select Configuration Men u , then press E NTER . The Configurati on Menu opens.
24 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 2 From the Configuration Menu, select View Configura tion , then press E NTE R . The V iew Configu ration Screen opens. The following table provides a de scription of the fields shown on the screen.
25 Cr eating arrays www .gate wa y .com T o create an array : 1 From the Main Menu, select Configuration Men u , then press E NTER . The Configurati on Menu opens.
26 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 2 T o access the Array Configuration Menu, select Array Confi guration, then pre ss E NTER . The Array Configuratio n Menu opens. The Array Configuration Menu lets you review , create, delete, or other wise modify the activ e arrays.
27 Cr eating arrays www .gate wa y .com 3 From the Array Co nfiguration Menu, select Create Arra y , then pr ess E NTER . The Array Name screen op ens.
28 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 4 T y p e a n a m e f o r t h e a r r a y ( u s i n g a s m a n y a s 3 2 c h a r a c t e r s ) , t h e n p r e s s E NTER . Th e RAI D Le vel screen opens. 5 Highlight the appropria te RAID level, then press E NTER .
29 Cr eating arrays www .gate wa y .com 6 Sele ct Ma nual C onfig urat ion, then press E NTER . The Select Chunk Size screen opens. The available chunk sizes are 64 K, 128 K, and 256 K. This is the am ount of data that is written on a sin gle d rive before the controller mo v es to the next drive in the stripe.
30 Chapter 3: Cre ating Disk Arrays www .gate wa y .com In cases where y ou are performing larger writes to the controller , you could go up to 2 MB for a stripe size, since y o u have more data to c luster . Never exceed 2 M B for a stripe size, since the contr oller cannot cluster over this size.
31 Cr eating arrays www .gate wa y .com 7 Select the desired chunk size from the menu, then press E NTER . Th e Drive Selection Me nu opens. 8 Select the drives for the new array by doing the following: The controller will list all th e available drives for each attached enclosure(s).
32 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 9 T o continue, press the C TRL + D keys when you have complet ed your selections. The Drive Ca pacity R eser ve screen open s. Tips & T ricks The driv e capacit y reserve determines how m uch drive capacity to retain f or future cap acity fluctuatio ns of replacem ent drives .
33 Cr eating arrays www .gate wa y .com 10 T ype the corre ct value for the drive capacity reserve (percentage), then press E NTER . Th e Sub-Array Selection screen opens. The controller displays the number of available sub-arrays you can choose from.
34 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 11 Sel ect th e number of sub -array s requ ired, t hen pre ss E NTER . Th e Initiali ze/T rust Arrays screen open s. 12 Sele ct Initialize Arra y , then press E NTER . The Save Configuration screen opens.
35 Cr eating arrays www .gate wa y .com 13 Save the confi guration to create the array . Click Ye s , then press E NTER . Y ou will see a message that t he c onfigurat io n is being saved. 14 After it has completed the process, press any key to continue.
36 Chapter 3: Cre ating Disk Arrays www .gate wa y .com Configuring arra y read-ahead and writebac k cac he The following steps will guide you thro ugh configuring the read-ahead cache and writeba ck cache opt ions for each a rra y . Each array has a different set of cache settings.
37 Configuring a rray read-a head and write back cache www .gate wa y .com T o configure the read-ahead cache: 1 From the Main Menu, select Configuration Men u , then press E NTER .
38 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 2 From the Configu ration Menu, select Array Con figuration , then press ENTER . The Array Conf iguration Men u ope ns. 3 From the Array Configuration Menu , select Arra y Cac he Configuration , then pre ss E NTER .
39 Configuring a rray read-a head and write back cache www .gate wa y .com 4 From the Array Cache Configuration Menu, select Read- Ahead Cache , then pre ss E NTER . The Select Array screen opens. 5 Press the up or down arrow keys to select an array , then press E NTER .
40 Chapter 3: Cre ating Disk Arrays www .gate wa y .com The choices are Au t om a ti c , Disabled , and four pre-determined sizes. Select A utomatic (the default), and recommended setting. It lets the c ontroller determine the optimum setting. Disab led w ill turn off the read-ahead cache.
41 Configuring a rray read-a head and write back cache www .gate wa y .com Normally , write-intensive operations wi ll benefit through higher performa nce when writeback cache is enabled on that array . Read-i ntensive operations, such as a strea ming ser ver , may no t benefit from writeback cache.
42 Chapter 3: Cre ating Disk Arrays www .gate wa y .com T o configure the writeback cache: 1 From the Main Menu, select Configuration Men u , then press E NTER .
43 Configuring a rray read-a head and write back cache www .gate wa y .com 2 From the Configurati o n Menu, select Array Con fig urati on , then press E NTER . The Array Conf iguration Menu opens. 3 From the Array Configura tion menu, select Array Cac he Configuration Men u , then press E NTER .
44 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 4 From the Array Cache Configuration Menu, select Writeb ack Cach e , then pre ss ENTER . The W riteback Parameters Select Array menu opens.
45 Configuring a rray read-a head and write back cache www .gate wa y .com 5 Press the up and down arrow keys to select an array from the list to which you want to make changes, then press E NTER . The W riteba ck Cach e Parameters Menu op ens. 6 Choose a W rit eback Cach e paramete r to use for the selecte d array .
46 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 7 Press C TRL + D to save t he ch anges. The Save Configuration screen open s. 8 Sele ct Ye s to save the configurati o n changes, then press E NTER .
47 Assign ing hot spa re drives www .gate wa y .com Assigning hot spare drives The process of configurin g fault tolerant arrays includes a ssigning drives for global or dedicated hot spa res. In the event of a drive failure, the controller will use a g lobal hot s pare to replac e the failed d rive in any array .
48 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 2 From the Co nfiguration menu, press the up or do wn ar ro w k ey s to s e le ct Hot Spar e Configuration me nu, then press E NTE R . The Hot Sp are Config uration Menu ope ns. 3 T o a dd or remove a h ot spare drive, select Add or Remove P ool and Dedicated Spare , then press E NTER .
49 Assign ing hot spa re drives www .gate wa y .com 4 Press the arrow keys to highlight an available drive to use, then press S to assign that dri v e as a dedicated spa r e. Continue to press S to display the arrays from which you c a n assig n the dedicated spare.
50 Chapter 3: Cre ating Disk Arrays www .gate wa y .com Deleting an arra y T o delete an array: 1 From the Main Menu, select Configuration Men u , then press E NTER .
51 Deleting a n array www .gate wa y .com 2 From the Configura tion Me nu, select Ar ra y Configuration M enu, then press E NTER . Th e Array Configuration Menu open s. 3 From the Array Configuration Menu, select Delete Array , then press E NTER . The Delete Array screen opens.
52 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 4 Press the up and down a rrow keys to select the array to delete, then press E NTER . 5 T o complete the deletion, select Ye s , then press E NTER .
53 Expandi ng an array www .gate wa y .com Expanding an arra y The Expand Array option lets you expand the capacity of your existing array by adding more drives or a dding sub-arrays. Using a RAID 5 array example, adding more drives to the array lets you increase the capacity of that array .
54 Chapter 3: Cre ating Disk Arrays www .gate wa y .com Addi ng additional dri v es T o add additional drives: 1 From the Main Menu, select Configuration Men u , then press E NTER .
55 Expandi ng an array www .gate wa y .com 2 From the Configuration Menu, select Arra y Configuration Men u , then press E NTER . Th e Array Configuration Menu open s. 3 From the Array Config urat ion Menu, select Expand Arra y , then press E NTER . The Select Array t o Expand Menu opens.
56 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 4 Press the up and down arro w keys to select an array to expand, then press E NTER . Th e Ex pansi on menu opens. 5 From the Exp ansion menu, select Add a Number of Drives to the Arra y , then pre ss E NTER .
57 Expandi ng an array www .gate wa y .com 6 Press the up and down arrow keys to select a drive, then press X to mark that drive for exp ansion. Continue to select additional drives if necessary , otherwise press C TRL + D to continue.
58 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 2 From the Configurati on menu, select Array Configuratio n Menu , then p re ss E NTER . Th e Array Configuration Menu open s. 3 From the Array Co nfiguration Menu, sele ct Expand Array , then press E NTER .
59 Expandi ng an array www .gate wa y .com 4 Press the up and down arro w keys to select an array to expand, then press E NTER . Th e Ex pansi on Me nu op ens. 5 Press the up and down arrow keys to select Add a Number of Sub-Arrays to the Current Arra y , then press E NTER .
60 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 6 Press the up and down arrow keys to select a drive, then press X to mark that drive for exp ansion.
61 Tr usting an arr ay www .gate wa y .com T rusting an arra y When you create a RAID 5 or 50 array , you have the option to trust the array . This option s ho uld only be used in environments where you ful ly und e rstand the consequences of the func tion.
62 Chapter 3: Cre ating Disk Arrays www .gate wa y .com 3 Y ou are prompted to save the co nfiguration. Select Ye s t o s a v e t h e configuration, t hen press E NTER .
4 63 Logical Drives This cha pter pro vid es inf orm atio n on crea tin g logi cal drives. Read this chapter to learn how to: ■ Configure a logical drive ■ Access the LUN conf iguration menu ■ V.
64 Chapte r 4: Logical D rives www .gate wa y .com Over vie w A Log ical Drive is defined as a region o r combination of r egions of unused space on the array(s) which makes the logical drives available to the host operating systems as a disk. Y ou can create up to 512 logica l dri v es.
65 Over vie w www .gate wa y .com Mapped Logica l Driv e Numb er Each logic al drive i s presented to the host syste m with a unique LU N. In certain cases (s uch as after de leting another logical driv e) it ma y be desir abl e to change the number of the logic al drive .
66 Chapte r 4: Logical D rives www .gate wa y .com Accessing the LUN configuration menu T o access the LUN configuration menu: 1 From the Main Menu, select Configuration Men u , then press E NTER .
67 Acces sing the LUN co nfigurati on menu www .gate wa y .com 2 From the Configuration Menu, sel ect LUN Configuration , then press E NTER . The LUN Configu ration Menu opens.
68 Chapte r 4: Logical D rives www .gate wa y .com Vie wing unassigned free space Prior to creating a logical drive, you may w ant to revi ew the availab le unas signe d free space. This will help you to identify th e unused regions or segmen ts for use during the creation of your logi cal driv es.
69 Viewing un assigne d free space www .gate wa y .com 2 From the Configu ration Menu, select LUN Configuration , then press E NTER . The LUN Confi guration Menu opens. 3 From the LUN Configuration Menu, select LUN Manageme nt , then press E NTER . Th e LUN Management Menu opens.
70 Chapte r 4: Logical D rives www .gate wa y .com 4 From the LUN Management Men u, sel ect View Un assigned Free Spa ce , th en pre ss E NTER . The Unassign ed Free Space scr een opens.
71 Creatin g a logica l drive www .gate wa y .com Creating a logical drive T o complete the process of configuring your arrays, you will need to create one or more logica l drives. Creating a logical drive from the available free sp ace regions presents the logical driv e to the host operating system.
72 Chapte r 4: Logical D rives www .gate wa y .com 2 From the Configuration menu, select LUN Configura tion , th en pres s E NTER . Th e LUN Confi guration Menu open s. 3 From the LUN Configuration menu, select LUN Management , t he n press E NTER . The LUN Man agement Menu open s.
73 Creatin g a logica l drive www .gate wa y .com 4 From the LUN Management me nu, se lect Crea te Logi cal Dr ive , then pres s E NTER . Th e S e l e c t U n u s e d R e g i o n M e n u op ens. 5 Press the up and down arrow keys to select a region you want to use for the logical drive, then press E NTER .
74 Chapte r 4: Logical D rives www .gate wa y .com 6 Press the up and down arrow keys to change the desired number of Host LUNs to create, then press E NTER . The LUN S ize scr een opens. 7 Press the up and dow n arrow keys to change the desired size of the LUN, then pre ss E NTER .
75 Creatin g a logica l drive www .gate wa y .com Expandi ng a logi cal drive T o expand a LUN: 1 From the Main Menu, select Configuration Men u , then press E NTER .
76 Chapte r 4: Logical D rives www .gate wa y .com 2 From the Configuration menu, select LUN Configura tion , th en pres s E NTER . Th e LUN Confi guration Menu open s. 3 From the LUN Configuration Menu, select LUN Management , then press E NTER . The LUN Man agement Menu open s.
77 Creatin g a logica l drive www .gate wa y .com 4 From the LUN Management menu, se lect Expand Logical Dri ve , then press E NTER . Th e Select Logical D rive screen op ens. 5 Select a logical drive that you w ant t o expa nd, then press E NTER . The Unused Reg ion s For Expa nsio n screen op ens.
78 Chapte r 4: Logical D rives www .gate wa y .com 6 Select the unused region into which you want to expand the logical drive, then press E NTER . The Ex pansi on Si ze screen opens. 7 Press the up and d own arrow keys to change the value to the desired size, then press E NTER .
79 Creatin g a logica l drive www .gate wa y .com Setting logical d rive a va ilability This option will make a l ogical drive a vailable to a c ontroller port and determines whether that logical drive is seen by all or a specific host system attached to th at controller port.
80 Chapte r 4: Logical D rives www .gate wa y .com 2 From the Configura tion menu, select LUN Configura tion , then pres s E NTER . The LUN Confi guration Menu opens. 3 From the LUN C onfiguration menu, s e lect LUN M anagement , th en p res s E NTER .
81 Creatin g a logica l drive www .gate wa y .com 4 From the LUN Management Menu, select Set Host LUN A vailability , then pre ss E NTER . The Select Logical Drive fo r A vailab ility scre en opens. 5 From the Select Logical Drive for A vailability screen, select a logical drive that you want to map t o another LUN number , then press E NTER .
82 Chapte r 4: Logical D rives www .gate wa y .com 8 Press C TRL + D to save the changes. 9 When prompted to sa ve the configuration, select Ye s , t hen press E NTER . 10 Press any key to return to the Main Menu. Deleteing a logical drive This process will remove an exist ing logical drive.
83 Creatin g a logica l drive www .gate wa y .com 2 From the Configura tion menu, select LUN Configura tion , then pres s E NTER . The LUN Confi guration Menu opens. 3 From the LUN Configura tion menu, select LUN Management , the n pre ss E NTER . Th e LUN Management Menu opens.
84 Chapte r 4: Logical D rives www .gate wa y .com 4 From the LUN Management Menu, select Delete Logical Drive , then press E NTER . Th e Select a Logical Drive to Delete screen opens. 5 From the Select a Logical Drive to Dele te screen, select the logica l drive to delete, then press E NTER .
85 Creatin g a logica l drive www .gate wa y .com Modifying a mapped LUN This option lets yo u change the assigned LUN number after the logical drive has previously been made available. T o modify a LUN number: 1 From the Main Menu, select Configuration Men u , then press E NTER .
86 Chapte r 4: Logical D rives www .gate wa y .com 2 From the Configura tion menu, select LUN Configura tion , then pres s E NTER . The LUN Confi guration Menu opens. 3 From the LUN C onfiguration menu, s e lect LUN M anagement , th en p res s E NTER .
87 Creatin g a logica l drive www .gate wa y .com 4 From the LUN Mana gement menu, select M odify Mapped LUN Numbe r , then pre ss E NTER . The Select a Logical D r iv e to Modify Map ped Number screen opens.
88 Chapte r 4: Logical D rives www .gate wa y .com 6 Press the up and down arrow keys to change the logical drive number to the desired number , then press E NTER . 7 When you are prompted to save the configuration, select Ye s , then press E NTER . 8 Press any key to return to the Main Menu.
5 89 SAN LUN Mapping This chapter provides informati o n on SAN LUN ma pping. Read thi s chapter to le arn how to: ■ Access the SAN LUN mapping configuration menu ■ View SAN LUN mappings ■ Creat.
90 Chapter 5: SAN LUN Mapping www .gate wa y .com Over vie w When attaching mu ltiple host systems in a SAN environment, it may be necessary to more precisely control which hosts ha ve access t o which logical dr ives.
91 Access ing the SA N LUN mapping configur ation menu www .gate wa y .com Accessing the SAN LUN mapping configuration men u T o access the SA N LUN mapping configuration m enu: 1 From the Main Menu, select the Configuration Men u , then press E NTER .
92 Chapter 5: SAN LUN Mapping www .gate wa y .com 2 From the Configu ration Menu, select LUN Configuration , then p ress E NTER . The LUN Confi guration Menu open s. 3 From the LUN Config ur ation menu, sele ct SAN LUN Mapping , then press E NTER . The SAN LUN Mapping screen open s.
93 Viewin g SAN LU N mappings www .gate wa y .com Vie wing SAN LUN mappings T o view existing SAN LUN mapping s, choose this option. T o view SAN LUN mappings: 1 From the Main Menu, select the Configuration Men u , then press E NTER . The Configurati on Menu opens.
94 Chapter 5: SAN LUN Mapping www .gate wa y .com 2 From the Configuration menu, select LUN Configura tion , th en pres s E NTER . Th e LUN Confi guration Menu open s. 3 From the LUN Config ur ation menu, sele ct SAN LUN Mapping , then press E NTER . The SAN LUN Mapping screen open s.
95 Viewin g SAN LU N mappings www .gate wa y .com 4 From the SAN LUN Mapping Menu, select View SAN LUN Mapping s , then p ress E NTER . The View SAN LUN Mapping screen op ens. In the example abo ve, there are two mappin gs created. They have a n identical node name but dif ferent port names, indicating they are both in the same host system.
96 Chapter 5: SAN LUN Mapping www .gate wa y .com Creating a SAN LUN mapping T o create a SAN LUN mapping: 1 From the Main Menu, select the Configuration Men u , then p ress E NTER .
97 Creating a SA N LUN mapping www .gate wa y .com 2 From the Configuration menu, select LUN Configuration , then p ress E NTER . The LUN Confi guration Menu open s. 3 From the LUN Configur ation me nu, select SAN LUN Ma pping , then press E NTER . The SAN LUN Mapping screen open s.
98 Chapter 5: SAN LUN Mapping www .gate wa y .com 4 From the SAN LUN M apping Menu, select Create SAN LUN Mapping , then press E NTER . Th e SAN LUN Mapping Name screen opens. 5 T y p e a u n i q u e n a m e f o r t h i s m a p p i n g ( a s m a n y a s 3 2 c h a r a c t e r s ) , t h e n p r e s s E NTER .
99 Creating a SA N LUN mapping www .gate wa y .com If a LUN is already part of another mapping and is defined as Exclusive, it will not be available here for select io n. If the logi cal driv e was mapped as Sha re or Shared Read Only , it will be available.
100 Chapter 5: SAN LUN Mapping www .gate wa y .com Deleting a SAN LUN mapping T o delete a SAN LUN mapping: 1 From the Main Menu, select the Configuration Men u , then p ress E NTER .
101 Deleting a SAN LUN mapping www .gate wa y .com 2 From the Configu ration Menu, select LUN Configuration , then press E NTER . The LUN Confi guration Menu opens. 3 From the LUN Configuration Menu, select SAN LUN Mapping , then press E NTER . Th e SAN LUN Mapping scr een opens.
102 Chapter 5: SAN LUN Mapping www .gate wa y .com 4 From the SAN LU N Mapping menu, select Delete SAN LU N Mappin g , then pre ss E NTER . The Dele te SAN LUN Mapping screen opens. 5 Select a SAN LUN Mapp ing to be deleted, then press E NTER . 6 When you are prompted to save the configuration, select Ye s , then press E NTER .
103 Modifyi ng SAN LUN M apping www .gate wa y .com Modifying SA N LUN Mapping I t i s s o m e t i m e s n e c e s s a r y t o m o d i f y s o m e o r a l l o f t h e p a r a m e t e r s o f a S A N L U N Mapping. Y ou can change the Mapping Name, Port Name, and the RAID controller port availabi lity access of the mapping.
104 Chapter 5: SAN LUN Mapping www .gate wa y .com 2 From the Configuration menu, select LUN Configura tion , th en pres s E NTER . Th e LUN Confi guration Menu open s. 3 From the LUN Config ur ation menu, sele ct SAN LUN Mapping , then press E NTER .
105 Modifyi ng SAN LUN M apping www .gate wa y .com 4 From the SAN LUN Mapping menu, select Modify SAN LUN Mapping , then pre ss E NTER . The Modify SAN LUN Mapping screen opens. 5 Press the up and down arrow keys to select a SAN LU N Mapping to be modified, then press E NTER .
106 Chapter 5: SAN LUN Mapping www .gate wa y .com 6 Enter a new SAN LUN mapping n ame, then pre ss E NTER . The Modify SAN LUN Mapping Co nfiguration screen opens.
107 Modifyi ng SAN LUN M apping www .gate wa y .com 9 When you are prompted to save the configuration, select Ye s , then press E NTER . 10 Press any key to return to the Main Menu.
108 Chapter 5: SAN LUN Mapping www .gate wa y .com Vie wing connected hosts Choose this option t o view a ll conn ected host HBA ports. T o view connected hosts: 1 From the Main Menu, select the Configuration M enu , then press E NTER . The Configurati on Menu opens.
109 Viewing c onnected hos ts www .gate wa y .com 2 From the Configura tion menu, select LUN Configura tion , then pres s E NTER . The LUN Confi guration Menu opens. 3 From the LUN Configura tion menu, select SAN LUN Mapping , then press E NTER . Th e SAN LUN Mapping scr een opens.
110 Chapter 5: SAN LUN Mapping www .gate wa y .com 4 From the SAN LUN Map ping Menu, select Vie w Connected Host , then press E NTER . Th e View Logg ed-in Ho sts sc reen opens. The following table provides an explana tion of each of the fields shown in the display .
6 111 Ad v anced Configuration and Mana g ement Thi s cha pte r pro vid es in for mat ion on adv anc ed config uration an d managemen t. Read th is chapte r to learn how to: ■ Set rebuild parameters.
112 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com Setting reb uild parameter s The Rebuild Parameters m e nu option lets you enable or disable automatic rebuild operations, set the rebuild p riority , and configure the controller for the auto hot sp are feature.
113 Sett ing rebui ld param eters www .gate wa y .com 2 From the Configurat io n menu, select Reb uild Parameter s , then press E NTER . The Rebui ld Parameters menu opens. 3 From the Rebuild Parameters menu, select the A uto Rebuild and Set Priority option, then pre ss E NTER .
114 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com 5 Press C TRL + D to save the changes a nd continue. 6 When you are pro mpted to confirm the save, choose Ye s , then press E NTER . 7 Press any key to return to the Main Menu.
115 Sett ing rebui ld param eters www .gate wa y .com Configuring auto hot spare This feature lets y o u config ure the controller to automatically start a rebuild operation when a rep lacement drive is inserted into the drive slot of the removed failed drive member .
116 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com 2 From the Configurati o n Menu, select Rebuil d Parameter s , then press E NTER . The Rebuild P arameters Menu opens. 3 From the Rebuild Parameters Menu, select the A uto Hot Spare option, then press E NTER .
117 Sett ing rebui ld param eters www .gate wa y .com 4 Press E NTER to toggle between Enable or Disable . Enabling this feature will automaticall y start a rebuild operation when a replacement driv e is inserted into the drive slot of the rem oved failed drive member .
118 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com Configuring hot spares The process of configurin g fault tolerant arrays includes a ssigning drives as global or dedicated hot s pare s.
119 Configur ing hot sp ares www .gate wa y .com 2 From the Configurat ion menu, select Hot Spare Configuration , t hen p ress E NTER . Th e Hot Spare C onfiguration menu ope ns.
120 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com 3 Sele ct View Hot Spare Dri ve Configuration, then press E NTER . A list of hot spare drives opens.
121 Configur ing hot sp ares www .gate wa y .com Addi ng or removin g hot spare drives T o add or remove hot spare drives: 1 From the Main Menu select Configuration Men u , then press E NTER .
122 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com 2 From the Configu ration menu, select Hot Spare Configur ation , then press E NTER . The Hot Spar e Configurati on menu opens. 3 Sele ct Add or Re move Glo bal and Dedica ted Spare, then pr ess E NTER .
123 Configur ing hot sp ares www .gate wa y .com 4 Pre ss th e ar row k eys to se lect an availa ble drive to use: T o add a dedicated spare, pres s S to assign that drive as a dedicated spare. Then continue to press S , which displays the arrays from which you can assig n the dedicated spare.
124 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com Configuring the har d ware The hardware configuration menu provides the options to set the Controller LUN, configure the con.
125 Config uring the hardware www .gate wa y .com T o configure the controller LUN: 1 From the Main Menu, select Configuration Men u , then press E NTER . The Configurati on Menu opens. 2 From the Configura tion Menu, select Har dware Configuration , then press ENTER .
126 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com 3 From the H ardware Configuration Menu, selec t Controlle r LUN , then press E NTER . Th e Set Controller LUN screen open s. 4 Press E NTER to select the method of Co ntroller LUN assignment.
127 Config uring the hardware www .gate wa y .com Setting the contr oller por t ID The Port ID settings provide you the option to set the SCSI ID for the controller port. Y ou can use IDs 0-15 . T o set the ID for controller ports: 1 From the Main Menu, select Configuration Men u , then press E NTER .
128 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com 2 From the Configuratio n Menu, select Hardware Confi guration , then press ENTER . The Hard ware Conf igu rati on M enu ope ns. 3 From the Hardware Configuration Menu, select P or t ID Settings , then press E NTER .
129 Config uring the hardware www .gate wa y .com The Disabled setting allows for soft a ddressing. The default IDs for the controller ports are Port 0 ID 4 and Port 1 ID 5. 5 Press C TRL + D to save the changes a nd continue. 6 When you a re prom pted to con firm the save, choose Ye s , then press E NTER .
130 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com Contr oller port data rate This option lets you set the data transfer rate of the controller ports. The settings include 320 MB , 160 MB and 80 MB. T o set the controller port data rate: 1 From the Main Menu, select Configuration Men u , then press E NTER .
131 Config uring the hardware www .gate wa y .com 2 From the Configuratio n Menu, select Hardware Confi guration , then press ENTER . The Hard ware Conf igu rati on M enu ope ns. 3 From the Hardware C onfiguration Menu, select Contr oller Port Data Rate , then press E NTER .
132 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com 4 Use the up an d down arrow key s to choose a controller p ort, then press E NTER . The Host Po rt D ata Ra te Op tions screen opens. 5 Use the up and down arrow keys to select 320MB/s ec , 160MB/se c , or 80 MB /sec , then press E NTER .
133 Config uring the hardware www .gate wa y .com Setting the RS-232 configur ation The RS -232 Settings optio n provides you with the option to set the BAUD rate for the controller’ s RS-232 port. T o change RS-232 settings: 1 From the Main Menu, select Configuration Men u , then press E NTER .
134 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com 2 From the Configuratio n Menu, select Hardware Confi guration , then press ENTER . The Hard ware Conf igu rati on M enu ope ns. 3 From the Ha rd ware Co nfiguration Menu, select RS-232 Settings , the n press E NTER .
135 Config uring the hardware www .gate wa y .com 4 Press the up and down arrow keys to select a BAUD rate for the controller RS-232 port (the default and recomme nded setting is 115,200), then press E NTER . 5 When you are prompted to save the configuration, select Ye s , then press E NTER .
136 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com P ac ketiz ed data transfers/QAS Packetized protocol is provided for transferring commands, status, and data. The system sends this i nformation in packets that are protected with a CRC.
137 Config uring the hardware www .gate wa y .com 2 Press the up or down arrow keys to select Pack etized Dat a T ransfers Usi ng QAS, then press E NTER . The Packetized SCSI/QAS screen opens. 3 Press t h e u p o r d o w n a r r o w k e y s t o s e l e c t Enable d or Disabled .
138 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com Vie wing contr oller inf ormation This option provides the abil ity to view detailed information on the SA T A RAID Controller , such as: Contro ller WWN, Configuration WWN and Name, Firmware, run-t ime data an d onboard tempera ture and voltage information.
139 Viewi ng contro ller infor mation www .gate wa y .com 2 From the Co ntroller Information Menu, press the up and d own arrow keys to select a C ontrol ler , then press E NTER . The Contr olle r Info rm atio n screen opens. 3 Use U and D to scroll up a nd down thro ug h the controller information displayed.
140 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com Clearing the configuration T o clear the configuration: 1 From the Main Menu, select Configuration Men u , then press E NTER .
141 Clearing th e configur ation www .gate wa y .com 2 From the Configuratio n Menu, select Clear Configur ation , then pre ss E NTER . The Cle ar Configuration W arning op ens. 3 Press Y to continue and clear all configuration information or N to cancel this operation 4 Press E SC to return to the Main Menu.
142 Chapter 6: Advanced Con figurati on and Manag ement www .gate wa y .com.
7 143 Ad ditional Configuration This chapter prov ides information on additi onal configuration. R ead this chapter to learn how to: ■ Modify config uration names ■ Modify config uration WWNs ■ .
144 Chapter 7: Additional Co nfiguration www .gate wa y .com Modifying the configuration name T o modify the configuration name: 1 From the Main Menu select Configuration Men u , then press E NTER .
145 Modifyin g the config uration n ame www .gate wa y .com 2 From the Configurat ion menu, select Additional Configu ration , then press E NTER . Th e Addition al Configuration Menu opens. 3 Press the up and down arrow keys to select Modify Configuration Name , then pre ss E NTER .
146 Chapter 7: Additional Co nfiguration www .gate wa y .com 4 Press B ACKSPACE to delete the existing Conf iguration Name displayed, type a new name for your controller’ s Confi guration (as many as 64 A SCII characters), then press E NTER to con tin ue.
147 Veri fying back ground media www .gate wa y .com V erifying bac kgr ound media This option, when ena bled, will automatically verify the m e dia of all drives in the background. If a media error is detect ed, the controller can automatically re-write the data, provi d ing tha t the array is in a fault tolerant mod e.
148 Chapter 7: Additional Co nfiguration www .gate wa y .com 2 From the Configuration menu, select Addition al Configuration , then press E NTER . The Addit ional Configu ration Menu opens. 3 From the Additional C onfiguration Menu, select Backgr ound V erification , th en pre ss E NTER .
149 Veri fying back ground media www .gate wa y .com 6 When you are prompted to save the configurat ion, select Ye s , then press E NTER . 7 Press any key to return to the Main Menu.
150 Chapter 7: Additional Co nfiguration www .gate wa y .com Inc luding enc losure e vents in e vent logs This option lets you enable or disable whether enclosure ev ents are included in the Event logs. E nclosure e vents are thos e which perta in to the enclosure components such as cooling fan status , power supply status, and I/O card status.
151 Includi ng enclosur e events in e vent logs www .gate wa y .com 2 From the Configurat ion menu, select Additional Configu ration , then press E NTER . Th e Addition al Configuration Menu opens. 3 From the Addition al Configuration Menu , select Log Enc losure Events , the n pre ss E NTER .
152 Chapter 7: Additional Co nfiguration www .gate wa y .com 6 When you are prompted to save the configuration, select Ye s , then press E NTER . 7 Press any key to return to the Main Menu.
8 153 Statistics This chapter provides informat ion on statist ics. Read this chapter to learn how to: ■ Vi ew a ll st a ti s ti c s ■ View access statistic s ■ View readahead statistics ■ Vie.
154 Chap ter 8 : Stati stic s www .gate wa y .com Over vie w The RAID controller monitors all inco ming co mmands and calculates v arious statistics. These statist ics are then reported to the controller’ s serial interface, whe re y ou can vie w thi s da ta.
155 Viewing al l statis tics www .gate wa y .com Vie wing all statistics T o view al l statistic s: 1 From the Main Menu, select Statistics Men u , then press E NTER .
156 Chap ter 8 : Stati stic s www .gate wa y .com 2 From the Select Controller S tatistics Menu, select the controller on which you want to view the statistics, then press E NTER . The Statist ics T ypes screen opens. 3 From the Stati stics T ypes screen, select View Al l Stati stics , then p ress E NTER .
157 Viewing al l statis tics www .gate wa y .com 4 Press U to page up, D to page do wn, and P to dump the information to a file. The balan ce of this ch apter covers ea ch statisti cs group se lected, with an exp lanati on of each it em. Dumping data to a text file The dump function ena bles you to write the data to a text file.
158 Chap ter 8 : Stati stic s www .gate wa y .com Vie wing access statistics The statistics groups can be viewed all together or individually , as well as on a LUN ( l o g i c a l d r i v e ) o r P o r t b a s i s .
159 View ing access statisti cs www .gate wa y .com T otal Read Comman ds Sinc e Reset This is a count of the to tal number of read accesse s that have occurre d since the s tatis tics were rese t or th e controll er was la st pow ered on.
160 Chap ter 8 : Stati stic s www .gate wa y .com Access Size This is the percentage of commands of t he size specifi ed. On o ccasions, an applic ation ma y sp ecify a particular access size , but the operatin g system ca n reduce th is. This c an lead to perf ormance prob lems.
161 Viewing r eadahead st atistics www .gate wa y .com Vie wing readahead statistics If se quent ial read comman ds are sent to t he controller , it assumes that the commands that follow can al so be sequential. It can then go and perform a read of the data before the host requ ests it.
162 Chap ter 8 : Stati stic s www .gate wa y .com Sequ enti al Comma nd Interval In determining wh ether to perf orm a readahead or n ot, the contro ller will se arch bac k in the command queue whene v er it receiv es a ne w read command th at is not satisfi ed by an e xis ting readahead cache b uff er .
163 Viewing command c luster stat istics www .gate wa y .com Vie wing command c luster statistics T o increase performance, the controlle r can cluster sequential write commands together to create a larger write comman d. This results in less commands being sent to the hard drives.
164 Chap ter 8 : Stati stic s www .gate wa y .com Statistic Descript ion Write Cluster Ra te This is the percentage of t he number of write commands that are part of a clust er versu s the total numb er of write command s that ha ve b een issu ed.
165 View ing misc ellaneou s statis tics www .gate wa y .com Vie wing miscellaneous statistics T o a i d i n t u n i n g p e r f o r m a n c e , s o m e a d d i t i o n a l s t a t i s t i c s h a v e b e e n i n c l u d e d for development use und er the Vie w Miscellaneous Sta tistics selection.
166 Chap ter 8 : Stati stic s www .gate wa y .com Vie wing access statistics on eac h logical drive T o view access s tatistics for each logical drive. 1 From the Main Menu, select Statistics Men u , then press E NTER . The Select Contro ller Statistics Menu opens.
167 View ing acce ss statisti cs on each l ogical dr ive www .gate wa y .com 2 From the Select Controller S tatistics Menu, select the controller on which you want to view the statistics, then press E NTER . The Statist ics T ypes screen opens. 3 From the Sta tistics T ypes screen, select Vi ew Access Stat istics on Each L UN , then press E NTER .
168 Chap ter 8 : Stati stic s www .gate wa y .com 4 From the Select LUN for Host LUN Statistics screen, select a LUN on which to view statistics, then press E NTER .
169 View ing acce ss statisti cs on each l ogical dr ive www .gate wa y .com 5 Select a Cont r oll e r Port on which to vi ew Statistics (eit her Port 1, Port 2 or Both Ports), then press E NTER . Th e View Access Statistics o n Each LUN screen opens.
170 Chap ter 8 : Stati stic s www .gate wa y .com Clearing access statistics on each logical drive (LUN) T o clear the access statistics for each logical drive: 1 Access the View Access Statistics o n Each LUN screen (s ee “Viewing access statistics on each logical drive” on page 166 ).
171 Cleari ng all statis tics www .gate wa y .com 2 From the Select Controller S tatistics Menu, select the controller on which you want to clear th e statistics, then press E NTER . The Statistics T ypes screen opens. 3 From the Statistics Ty pes screen, selec t Clear Statist ics , then press E NTER .
172 Chap ter 8 : Stati stic s www .gate wa y .com.
9 173 Event Logs This chapter provides information on event logs. Read this chapter to learn how to: ■ Access event logs ■ Understand controller events ■ Un dersta nd dri ve even ts ■ Understa.
174 Chapter 9: Event Logs www .gate wa y .com Accessing e vent logs The RAID controller has a compre hensive, no n-volatile ev e nt log th at can be used for monitoring con troller events and error co nditions.
175 Access ing ev ent logs www .gate wa y .com 2 From the Sele ct Cont roll er Ev ent Log Menu, select the controller for which you want to view the events, then press E NTER .
176 Chapter 9: Event Logs www .gate wa y .com 3 From the Event Log T ypes men u, select a specific set of events you want to view , then press E NTER . For example, if you selec t Vie w All Events , the Vi ew All Events screen opens. The balance of this chapter covers each Event Log group a vailable, with an exp lanati on of each it em.
177 Access ing ev ent logs www .gate wa y .com View Last 50 Ev ents This opt ion lists the l ast 50 e vents . View Last Hour/24 H our Eve nts This li sts the e v ents that occurred in the specif ied time . View Env ironmental Events This lis ts ev ents s uch as temper ature warnings , vo ltage le vel e rrors, battery errors, e tc.
178 Chapter 9: Event Logs www .gate wa y .com Contr oller e vents Following is a brief description of events that relate to the c ontroller and configuration.
179 Con troll er ev ents www .gate wa y .com Battery Charging This i ndicates tha t the onboard ca che bac kup battery is cha rging. Battery charging star ted.
180 Chapter 9: Event Logs www .gate wa y .com Controlle r x F ail ed/Remo ved The speci fied controller has been rem ov ed, or ha s fai led. Messa ge is genera ted b y the partner controller . F ail ure or r emoval of one co ntroller (partner) in an Activ e-Activ e configu ration.
181 Con troll er ev ents www .gate wa y .com Control ler Shutdown The controlle r has been shutdo wn either lo cally or remotely . User ini tiated a control ler shutdo wn. The c ontr oller tempera ture was ex ceeded a nd the control ler shut itself do wn.
182 Chapter 9: Event Logs www .gate wa y .com F ata l SDRAM ECC The contro ller has det ected unrecov erab le ECC errors on th e SDRA M, ei ther a mult iple-bit error or uncor recta ble single -bit error . F ault SDRAM or dama ged internal bus. Replace th e controll er .
183 Con troll er ev ents www .gate wa y .com Resy nc Started A stripe synchro nization of a RAID 5 /50 set has st ar ted. This w ill be done when a controll er f ails or when pow ered off during a wr ite . A controlle r f ails or is po wered off dur ing a RAID 5/50 write oper ation.
184 Chapter 9: Event Logs www .gate wa y .com Driv e e ve nts These events are related to the drive bus and arrays. Drive Eve nt Messages Description Cause Action Arra y xx Critic al This ind icates the sp ecified array is cr itic al. Driv e remov al or fai lu r e.
185 Dri ve even ts www .gate wa y .com Data Underrun WWN: xx xx xx x x xx xx P y OP: zz The con troller has de tected a data und errun from the indicat ed drive . This is caused by the co ntroller detecting a bad CRC in a frame , and us ually indic ates a link proble m, eit her wi th cab ling or an enc losure.
186 Chapter 9: Event Logs www .gate wa y .com Drive CC F ailure SN: xx xx xx xx xx xx A: yy D: zz The driv e listed has fa iled becaus e of an unreco ver able erro r.
187 Dri ve even ts www .gate wa y .com Dr ive Rebuild Failur e SN: xx xx xx xx xx xx A: yy D: zz Reb uild has f aile d because of an u nrecov erab le error on another driv e in the arr ay .
188 Chapter 9: Event Logs www .gate wa y .com New Driv e Re b uild F ai lure SN: xx xx xx xx xx xx A: yy D: zz Reb uild has f aile d because of an u nrecov erab le error on the ne w drive .
189 Dri ve even ts www .gate wa y .com SN: xx xx xx xx xx xx ID:aaa FW Download Sta r t Re v: yyyy The driv e listed has star ted a firmware u pgrade to t he indicat ed re vision. The meani ng of each f ield i s as fo l l ow s : SN: Serial Number ID: D rive T arg et ID Re v: New firm wa re version A firmware upgr ade has started.
190 Chapter 9: Event Logs www .gate wa y .com Contr oller drive por t (host) e vents These events are related to the host si de Controller Port. Contro ller Port Loop Ev ent Messages Description Cause.
191 Controll er drive port (host ) events www .gate wa y .com CC to Host ID: xxx LUN : yyy P z OP: aa SN: bb EXT: cc QL: dd This ind icates that an unreco ver able driv e error has occ urred f or a particular comma nd.
192 Chapter 9: Event Logs www .gate wa y .com Enc losure events These events are related to the SES mo nitored enclosure components. SES Event Mes sages Description C ause Action Encl. yy P ow er supply zz OK WWN: xx xx xx xx xx xx xx xx The con troller has de tected that the in dicated po wer supply is functioni ng corre ctly .
193 Enclosur e events www .gate wa y .com Encl. yy Te m p . zz < aa >C W arning WWN: xx xx xx x x xx xx xx x x The con troller has de tected that the in dicated temper ature sens or has reached a warning limi t. T emperatu re sensors are reporting enclos ure temper atures ha ve reached t he threshol d of 70°C.
194 Chapter 9: Event Logs www .gate wa y .com Encl. yy Te m p . zz < aa >C Critical WWN: xx xx xx xx xx xx xx x x The con troller has de tected that the in dicated temper ature sens or has reached a critical limit. T emperatu re sensors are repo r tin g enclos ure temper atures ha ve reached t he threshol d of 50°C.
195 Fail ed drives www .gate wa y .com F ailed drives The controller maintains a list of fa iled drives. Drives are listed in the fo llowing format: Failed Dri ve:xx WWN: yy y y yy yy yy yy Reason C ode The reason code c an be one of the following: Reason Co des Reason Action Driv e Timeout The driv e has eit her timed ou t or been remo ved.
196 Chapter 9: Event Logs www .gate wa y .com Clearing e vent logs T o clear event l ogs: 1 From the Main Menu, select Event Logs Menu , then press E NTER .
197 Clearing e vent logs www .gate wa y .com 2 From the Sele ct Cont roll er Ev ent Log Menu, select the controller for which you want to clear the event logs, th en press E NTER . The Event L og T ype s menu opens. 3 Fro m the Event Log T y pes me nu, s elect Clear Event Log , then press E NTER .
198 Chapter 9: Event Logs www .gate wa y .com 4 Fro m the Cl ear Ev ent Log screen , sele ct Ye s to clear all events on this controller , then press ENTER .
10 199 Dia gnostics This chapter provides information o n diagnos tics. Read this chapter to learn how to: ■ Access diagnostics ■ Use offline diagnostics ■ Use online diagnostics ■ Controller .
200 Chapte r 10: Diagnost ics www .gate wa y .com Accessing dia gnostics The RAID contro ller has a comprehens ive VT - 100 Diagnostics menu. The following operations can be per formed from the diagno.
201 Access ing diagn ostics www .gate wa y .com Important Offlin e diagnostic s can only b e perfo r med whe n there is no activ ity and req uires that th e enclosure b e disconne cted from the hos t system(s).
202 Chapte r 10: Diagnost ics www .gate wa y .com Using offline diagnostics T o view offline diagnostics: 1 Before perf o rmi ng this diagnostic, yo u mu st disconnect the host system(s) from the enclosure. 2 From the Mai n Menu, select Diagnost ics Menu , then press E NTER .
203 Using off line diagn ostics www .gate wa y .com 3 From the Diagnostics menu, select Offline D iagnostics , then press Enter . T he Offline Diagn ostics menu opens.
204 Chapte r 10: Diagnost ics www .gate wa y .com 5 Select the type of test you want performed. The Read or W rit e T e st screen opens. 6 Select the type of test to perform, the Te s t D u r a t i o n scree n o pens . 7 T ype the test duration, in minutes, then press E NTER .
205 Using on line diagn ostics www .gate wa y .com Using online diagnostics While the controller i s connected to the ho st, it is possible to perform Controller Maintenance, Drive M aintenanc e, RAID 5/50 Parity Check diagnostics , as well as to shutdown the controllers an d perform a diagnostics dump to the terminal window .
206 Chapte r 10: Diagnost ics www .gate wa y .com 2 From the Di agnostics me nu, select Online Diagn ostics , then press E NTER . The Onlin e Diagnostics menu op ens. 3 From the Online Diagnostics menu, selec t the o nline diagnostic te st you want to perform.
207 Control ler mainten ance - downlo ading firmwa re www .gate wa y .com Contr oller maintenance - do wnloading firmware There may be an occasion when yo u need to download new or updated co ntroller firmware or reload the current firmw are.
208 Chapte r 10: Diagnost ics www .gate wa y .com 4 When the Cs appear , select Send File from the T ransfer list (not shown). The Sen d File dialog box opens. 5 Click the brow se button and locate the new firmware file (similar to “W_t006.bin”), sele ct the 1K Xmodem protocol, then click Send .
209 Control ler mainten ance - downlo ading firmwa re www .gate wa y .com If you elect to stop a download in progress, make sure that the stop (abort) comman d was co mpleted b y clickin g the Cancel button. 6 After the transfer scr een disappear s, press E NTER .
210 Chapte r 10: Diagnost ics www .gate wa y .com 9 From the Diagnostics menu, select Reset Control ler , then press E NTER . The Select Contro ller to Reset menu opens. 10 From the Select Controller to Reset menu, select the con tro ller on which the firmware was changed, then press E NTER .
211 Drive mainte nance www .gate wa y .com Drive maintenance The controller can download firmwa re to the attached hard drives. Because of the large number of hard drives on the market, it is essential to use only a Gateway approved drive firmware file.
212 Chapte r 10: Diagnost ics www .gate wa y .com Do wnload the firmwa re from the host T o download firmware from the host: 1 From the Mai n Menu, select Diagnost ics Menu , then press E NTER . The Diagnostics menu opens. 2 From the Diagnostics menu, select Online D iagnostics , then press E NTER .
213 Drive mainte nance www .gate wa y .com 3 From the Online Dia gnostics menu, select Drive Maintenan ce , then press E NTER . The Drive Firmware Menu opens. 4 From the Drive Firmware Menu, select the Downloa d Drive Firmware to Buffer transfer method, then press E NTER .
214 Chapte r 10: Diagnost ics www .gate wa y .com 7 Select the 1K Xmo dem protocol, then click Send . The Xmodem fil e send scr een op ens. Y ou can f ollow the pr ogress of the downlo ad fr om this screen.
215 Drive mainte nance www .gate wa y .com 2 From the Diagnostics menu, select Online D iagnostics , then press E NTER . The Onlin e Diagnostics menu op ens. 3 From the Online Dia gnostics menu, select Drive Maintenan ce , then press E NTER . The Drive Firmware Menu opens.
216 Chapte r 10: Diagnost ics www .gate wa y .com 6 Choose one of the av ailable options and pre ss E NTER . Y ou can downl oad to all supported d rives, all supported unus ed or hot spar e driv es, or a ll supp orted drives t hat ar e not alr eady at this f irmware level.
217 Drive mainte nance www .gate wa y .com Chec king RAID 5/50 parity If an array is not ini tialized during creation (for example, trusted ), or if both controllers are replaced after the arra y is turned off w ith write operations in progress, you may need to verify the pa rity data on the array .
218 Chapte r 10: Diagnost ics www .gate wa y .com 2 From the Diagnostics menu, select Online D iagnostics , then press E NTER . The Onlin e Diagnostics menu op ens. 3 From the Onl ine Diagnost ics menu, selec t RAID 5/50 P arity Check , then press E NTER .
219 Drive mainte nance www .gate wa y .com 4 From the select RAID 5/50 Parity C heck Menu , sele ct e ith er A ll RAID 5/50 Array s or Specific RAID 5/50 Arrays , then press E NTER . Th e Pari ty Check Option Menu opens . 5 From the Parity Check Options Menu, select the parity check options you want to use.
220 Chapte r 10: Diagnost ics www .gate wa y .com When you have selected th e required options, press E NTER . The Apply Parity Check screen opens. 6 From the Apply Parity C heck screen, select Ye s , then press E NTER . The parity che ck st arts and the Par ity Chec k Men u returns.
221 Drive mainte nance www .gate wa y .com T o monitor commands: 1 From the Main Menu, select Diagnostics M enu , then press E NTER . The Diagn ostics menu opens. 2 From the Di agnostics me nu, select Online Diagn ostics , then press E NTER . The Onlin e Diagnostics menu op ens.
222 Chapte r 10: Diagnost ics www .gate wa y .com 3 From the Online Diagnostics menu, select T ar get Command T race Settings , then press E NTER . The T a rget Command T race Settin gs scree n opens. 4 From the T arget Command T race Settings screen, press E NTER to toggle the command trace to be Enab led or Disabled .
223 Shutting down t he cont roller www .gate wa y .com Shutting do wn the contr oller This option let s you gracefully shutdown the controller . When this method is used, all cache is written befo re t he controller is s hutdo wn. T o shutdown the controllers: 1 From the Main Menu, select Diagnostics M enu , then press E NTER .
224 Chapte r 10: Diagnost ics www .gate wa y .com 2 From the Diagnostics menu, select Shu tdown Contr oller , th en press E NTER . The Select C ontroller to Shut down scre en opens. 3 From the Select Co ntroller to Shutdown screen, select a cont roller you want to shutdown, t hen press E NTER .
225 Dumpin g diagnostic s www .gate wa y .com 5 T o restart the controller , you can either remove and re-insert t he RAID controller in its slot or turn the enclosure off t hen back on. Dumping dia gnostics Dur ing th e proce ss of t roubl eshoo ting a problem, it may be helpful to capture the diagnostics data.
226 Chapte r 10: Diagnost ics www .gate wa y .com 5 Repeat steps 1 and 2. 6 Sele ct Ca pture T ext > Stop from the T ransfer list . 7 Access the text file using a text editor .
A 227 Optimizing RAID 5 Write P erf ormance This chapter provides inf ormation on optimizing RAID 5 write performance. Read th is chapter to learn how to: ■ Understand optimizati on pa rameters ■ .
228 Appendi x A: Optimiz ing RAID 5 Wr ite Perfo rmance www .gate wa y .com Intr oduction W ith a typ ical RAID 5 implementation , there are a number of step s necessary to write the data to the media. Every write from the host syst e m will typically generate two XOR o perations and thei r associated data tran sfers to t wo drives.
229 Introdu ction www .gate wa y .com is used, then the st r ipe size is 1 MB (4 chunks × 256 K). So, for maximum performance, the host could eithe r send 5 × 1 MB write comman ds, or 20 × 256 K write co mmands. The effectiveness of the cont ro ller’ s ability to perform a Full Stripe W rite depends on a nu mber of parameters.
230 Appendi x A: Optimiz ing RAID 5 Wr ite Perfo rmance www .gate wa y .com T o g e t t h e h i g h e s t p e r f o r m a n c e f r o m t h i s s y s t e m , i t i s n e c e s s a r y t o h a v e a number of stripes being written i n parallel.
231 Using RAID 5 s ub-arrays www .gate wa y .com it is still o nly necessary to cluster four write commands together , as oppo se d to the seven necessar y as indicated below . T he ar ray of drives appears as two separate sub-arrays, each with it s own rotating parity .
232 Appendi x A: Optimiz ing RAID 5 Wr ite Perfo rmance www .gate wa y .com of the drives in the array . This increa ses both the rebuild speed and the speed of access to missing data , which also has to be recreated from the remainin g drives.
B 233 T echnical Suppor t Thi s cha pte r pro vid es in for mat ion on tro ubl esho ot ing. Read th is chapter to learn about: ■ Getting T ech nical Support ■ Notices.
234 Appendi x B: www .gate wa y .com T echnical Suppor t Gat eway of fers a wide r ange of cust omer serv ice, t echni cal sup port, and information services.
235 Notices www .gate wa y .com Notices Copy r ight © 2004 Gate way , Inc. All Rights Reserved 14303 Gatewa y Place P owa y , CA 92064 USA All Rights Reser ved This publication is protected b y copyright and all rights are reser ved.
236 Appendi x B: www .gate wa y .com.
237 Index A access align ment 229 access size 160 , 229 access statist ic s 158 accessing configuration ut ility 5 diagnostics 200 event logs 17 4 LUN configuration 66 RAID controllers 7 Add or Remove.
238 navigating 9 configuration WWN 14 configuring arr ay write back ca che 36 auto hot sp are 115 hot spare drives 47 readahea d cache 36 RS-232 port 13 3 writ eback ca che 36 connecte d hosts viewing.
239 Delete Ar ray scre en 51 deleting array 50 logical drive 82 SA N LUN ma ppin g 100 diagnostics 199 accessing 200 dumping 225 offline 202 online 205 downloading firmware 207 firmware from host 21 2.
240 time 15 free space viewing 68 H hardware configuration settin gs 124 Host Event CC to Ho st ID 191 Detected Power- on/Reset 19 0 L o g g e d i n a t I D 19 0 host events 190 hot spare c onfigurati.
241 packetized p rotocol 13 6 parameters commun ications 7 rebuild 112 pari ty check ing RAID 5/ 50 217 perfor mance optimizing RAID 5 write 227 pool spare (global) 49 Port Data Rate 130 port name 90 .
242 SCSI ID changing controller port 127 segmentation logical drive 64 S e l e c t a H o s t L U N t o M o d i f y M a p p e d Number screen 87 Select a Logical Drive to Delete sc r een 84 Select Arra.
243 controller information 13 , 138 free space 68 hot spare drives 118 miscellaneous statist ics 165 SA N LUN ma ppin gs 93 statistics 155 unassigned LUN free space 68 voltage controller 15 informatio.
244 8509736.
A MAN NST OR VT -100 SW GDE R0 1/04.
Ein wichtiger Punkt beim Kauf des Geräts Gateway 840 VT-100 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Gateway 840 VT-100 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Gateway 840 VT-100 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Gateway 840 VT-100 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Gateway 840 VT-100 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Gateway 840 VT-100 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Gateway 840 VT-100 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Gateway 840 VT-100. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Gateway 840 VT-100 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
