Benutzeranleitung / Produktwartung Metal Detector GTI 1500 des Produzenten Garrett
Zur Seite of 88
TM TM.
.
SPECIAL NOTICE The Gar ret t G TI 1 500 met al d ete cto r with T reasure Imaging and Graphic T arget Analyzer truly adds a new dimension to treasure hunting.
Although the GTI 1500 is built to with- stand rugged treatment outdoors while giving years of trouble-free service, always remember that this detector is a precision electronic instrument. Protect it from extreme heat and cold as well as mist, rain or blowing sand.
CONTENTS T o The Owner 6 Assembly 9 T ouch pads 13 Gr aphic T arget Display 16 Hunting Basics 21 Oper ating Adjustments 27 Control Settings 29 Search Aids 35 Oper ating Modes 38 Setting Discrimination.
TO THE OWNER As the proud owner of a Garrett GTI 1500, you enter a new and exciting world of treasure hunting. T reasure imaging and the Graphic T arget Analyzer enable you to find coins with an ease that will tak e your breath a way . Y ou will spend your hobby hours in recovering treasure, not digging tr ash.
• Use the T arget ID Guide to learn what you'v e found. • Pinpoint electronically to determine loca- tion of target and learn size and depth. • Find deeper treasures with computerized circuitry .
W elcome again to the Garrett fr aternity of successful treasure hunting hobbyists. Now , find your own coins and other treasures with the GTI 1500, one of the world’ s most capable and universal metal detectors, yet one that is amazingly easy to oper ate.
ASSEMBLY Y our GTI 1500 is shipped complete in one carton: A. Control Housing B. Upper and Lower Stems C. Imaging Searchcoil D . Parts Env elope E. T r aining DVD & Owner’ s Manual F . W arrant y R egistration Card Make certain all of these parts are included and are undamaged.
Inspect contents of the clear plastic env e- lope (see above) . • One (1) knob • T wo (2) W ashers • One (1) threaded bolt 1. A ttach the lower stem to the 9.5” imag- ing searchcoil. Make certain that the two rubber washers are inserted onto the lower stem before slipping the searchcoil onto it.
2. Depress buttons in the Control Housing stem and slide on the Upper Stem (see Image B above) . 3. Depress the buttons in the Lower Stem and insert it into the Upper Stem. Buttons will pop into the holes, and you can achieve the desired stem length. The third set of holes from the end is most com- monly used.
of the searchcoil can be changed easily , if required. T o connect the cable to the detector , insert the cable connector into the connector on the control housing as shown and rotate the collar clockwise until secure (approximately four (4) turns). (See Image D above.
GTI 1500 TOUCH PADS • Power/Hold to Reset T urns detector ON and OFF as well as returns it to factory settings when held. • Menu/Scroll Allows the Operator to scroll through the following settings to make adjustments or turn them ON or OFF .
—Custom Functions Menu Sensitivit y (Depth), Threshold (Audio Lev el), Frequency , V olume, T one, R echargable battery — Search Aids Salt Elimination, Belltone, Backlight • Accept / Reject P ermits acceptance or rejection of specific target segments shown on the Lower Scale to establish discrimination notches.
Jewelry , R elics, Z ero, Custom) that was previously being used. - & + These touch pads permit precise regula- tion of the GTI 1500 . Y ou will note that each press of a touch pad causes seg- ments on the Upper Scale to move either to the right (+) or to the left (-).
GRAPHIC TARGET DISPLAY Target ID Guide This guide printed abov e the LCD screen shows U.S . coin denominations, gold, sil- ver and other typical metallic objects. Upper Scale Indicates target discovered; Indicates tar- get strength in T reasure Imaging mode; Indicates levels of Menu control settings.
Operating Status The complete operating status of your detector is shown on the screen at all times. When the TREASURE IMAGING (pinpointing) touch pad is pressed and held, size and depth of targets will also be shown. The mode in which you are searching will alwa ys be shown on the left side of the screen under the MODE heading.
R echargeable (seen in lower right corner of LCD screen). When one of these func- tions has been illuminated by use of the MENU/SCROLL touch pad, it can be regu- lated by pressing the + or - touch pads. Treasure Imaging Five target sizes are shown on the color- coded Imaging diagr am at the bottom of the screen.
Size C - Ov al extending to C grid lines (purple): targets larger than coins and smaller than 12-oz. cans, such as large rings, small belt buckles, jewelry and such tr ash targets as screw tops, bottle caps and complete pull tabs. Size D - Oval extending to D grid lines (blue): larger belt buckles, large jew- elry items, 12-oz.
side of the diagr am and the horizontal color-coded lines connecting them. These refer to the five relative sizes at the bot - tom of the Display Screen. R elating conductivity and size to help determine y our target before digging it is a unique feature of the GTI.
HUNTING BASICS This One T ouch detector is toda y's most adv anced; yet, its basic automatic opera - tion mak es it as simple to operate as any detector ever manufactured. Y ou can begin hunting with it immediately . No spe- cial instructions are needed beyond what's included in the next few pages.
3. Y our GTI 1500 begins operating with all settings at factory -set levels. Any of the settings can be easily changed, but you many never want to do so! It is recom- mended that you use the factory settings the first few hours you hunt with your detector .
Discovery Detection of all metal targets will be indicated by the appear ance of a T arget Cursor on the Upper Scale. A cursor will appear , as shown below , to indicate every detected target and will remain for 4 seconds or until a new target is detected (whichever comes first).
Treasure Imaging (Pinpoint) Press and hold this touch pad to put your detector into a T reasure Imaging (Pinpoint) mode so that you can locate your target more precisely and also deter- mine its relative size and depth. Size will be shown at the bottom of the Display Screen, as shown abov e.
Coins mode and that you read carefully the W arning section in this manual. By now you are also certainly impressed with the super sensitivity , depth capabili- ties and the target analysis of this de.
Correct operating techniques will enable you to properly use all of the data pre- sented by your detector to become aw are of the precise nature of all targets.
OPERATING ADJUSTMENTS Status of each of the control selections will be shown on the LCD Gr aphic Display abov e the control panel touch pads. When you touch the POWER touch pad, your GTI 1500 is ready to hunt in a Coins operating mode with threshold, sensitivity (depth), tone and other controls preset at the fac- tory , as shown abov e.
unlike that of ordinary detectors, however , adapts automatically to the coil's r ate of mov ement. Y our searches will ha ve the same high degree of accur acy whether you are scanning r apidly to cover a large area quickly or moving methodically and very slowly ov er a location with multiple targets.
CONTROL SETTINGS Sensitivity (Depth) Press the MENU touch pad to display SENSITIVITY on the screen (shown with factory setting at approximately 75% as indicated on the Upper Scale), and you can use the + and - touch pads to adjust the sensitivity at which your detector will oper - ate most effectively .
Press + to increase sensitivity . Press - to decrease. A single touch and release adjusts the lev el in a small increment. Continuous pressing results in a continu- ous adjustment.
The audio will increase sharply when- ever a desir able target is encountered. (R emember , a cursor will indicate ev ery target.) When headphones are used, it will usually be necessary to decrease the threshold level since sound is more audible through headphones.
Whenever you hear unusual sounds and believe that y ou are encountering interfer - ence, press and release the MENU touch pad until FREQ appears on the screen (as shown on the previous page) . The Upper Scale will indicate the frequency at which your detector is now oper ating.
controls the maximum volume of sound produced by the GTI 1500 only when a target is encountered, it will not affect the threshold level you hav e already selected as the primary audio function of your detector . When headphones are used, it will usually be necessary to decrease v olume since detections sounds are louder ov er head- phones.
lower the pitch to a bass tone. All touches will mak e changes indicated on the Upper Scale. Experiment to find the pitch that suits your hearing. Battery Gauge The scale (lower right of screen) indicates the condition of standard (carbon or alka- line) or rechargeable batteries.
SEARCH AIDS Salt Elimination When hunting on an ocean beach, or ov er any ground with high salt content, you may want to use this Search Aid to elimi- nate interference caused by wetted salt. If you wish to turn on the Salt Elimination aid, use the MENU to display Salt Elim and press + when the word is blinking to turn it on.
is necessary at factory settings. T o turn off this function use MENU to display the word, press - and the word will begin blinking. Pressing + will turn it back on. Backlight This function of the GTI 1500 lights the control panel so that the detector can be used at night or in dark places.
with the v arious oper ating functions will be retained by the detector when you press POWER to turn the detector OFF . These personal alterations are held in a non- volatile memory circuit and retained even when the batteries are remov ed. The detector must be turned off when batteries are being replaced.
OPERATING MODES Press MENU and use the + touch pad to rotate through five different modes of detection that are av ailable, each with a specific discrimination configuration as shown on the Lower Scale.
treasure hunters, however , all understand that they must dig some junk occasionally . Correct oper ation of the GTI 1500 should reduce this wasted effort.
ing good targets in the lower conductivity r ange, items generally sought by most relic hunters. Zero Discrimination This mode, shown above, permits you to hunt with no discrimination and offers a method of "dual-mode" hunting. Y our detector will giv e a "beep" to announce any metal it scans over while a cursor indicates it.
retained by the detector's memory when it is switched OFF . Many GTI 1500 owners may r arely use the Custom mode, and will hunt only in the preset Coins, Jewelry , Relics or Z ero Discrimination modes. Complete instruc - tions for setting discrimination notches for any of these modes can be found on the following four pages of this manual.
SETTI NG DISCRIMIN ATION (Notc hes) Using only the discrimination of its factory - set Coins, Jewelry , Relics and Z ero oper at- ing modes, the GTI 1500 will more than satisfy the requirements of almost every treasure hunter . Many will nev er require any other discrimination.
First Method: While in the OPERA TE mode press the + and - touch pads to position the blinking cursor above the Discrimination Segment corresponding to the particular target to be detected or ignored. If the segment is turned on (showing), that target will be signaled audibly .
on. If it is showing, pressing this pad will turn it OFF . R emember: When you press the ACCEPT/ REJECT touch pad, you cause the dis- crimination circuit to reject a target that is shown on corresponding segments of both the Lower and Upper Scales. This rejection will be indicated by the disappearance of a Lower Scale segment.
modes return to factory -set detection settings each time the detector is turned OFF and turned back ON. Custom mode discrimination changes will be lost only when POWER is held for five (5) seconds for return of factory settings.
tors permit such accurate levels of precise discrimination. R eturn to factory settings by pressing and holding the POWER touch pad for 5 seconds. 46 - Garrett Metal Detectors.
TREASURE IMAGING Sizing and pinpointing targets precisely are important capabilities of your GTI 1500. Furthermore, when you press and hold the TREASURE IMAGING pad, the searchcoil can remain stationary over your target. Mov e the coil around slightly to try to center it directly over the target.
will notice a more distinct audio sound when the target is directly beneath the searchcoil's center . In addition, you will note that signal strength on the Upper Scale will increase. The Upper Scale cursor indicating the target just discovered will blink, even as signal strength is shown.
F our typical examples: Graphic T arget Imaging 1500 - 49.
Radiating Size Array While the TREASURE IMAGING touch pad is being pressed and held, y ou may occa- sionally observe a size reading that con- tinues to change dramatically , with the size appearing to "radiate" rapidly and continually outward from the small ov al at the center .
BENCH TESTING This will enable y ou to test typical targets and to learn about the discriminating capabilities of the GTI before taking it into the field or trying to set discrimination.
will cause a "beep ." Pa y particular atten- tion to the size of each target as indicated when you press and hold the TREASURE IMAGING touch pad. 2. Use the MENU/SCROLL and (+) or (- - ) touch pads to select the Coins detection mode. Then press OPERA TE.
OPERATING RECOMMENDATIONS As you walk, scan the searchcoil from side to side in a str aight line or slight arc. K eep the coil level and at a constant height of one or two inches abov e the ground while you move it at a rate of about one to three feet per second.
R aising the coil an inch or two as you scan ov er such soil is sometimes helpful. R emember to keep the coil level and at a constant height. Encrustation or patina may also affect conductivity of the target, resulting in improper classification.
Last Mode Use of this touch pad can be particularly helpful while scanning because it effec - tively conv erts your GTI 1500 into an instantaneous dual, or triple-mode detec- tor . Pr essi ng and rele asin g this touc h pad returns detector oper ations to the mode that has just previously been used.
Another indication of a reject target is an audio signal as you scan one way , and no response when scanning from the other direction. If y ou encounter a large target or scan too close to it, the detector will give an audible ov erload indication, which sounds lik e a buzzing alarm.
as ground and atmospheric conditions permit. Attempting to oper ate at sensitivi- ties above a level that permits a quiet and stable oper ation may actually cause you to miss deep targets that you would ha ve found had you not "pushed" the detector .
R emember that newly buried objects, especially coins, will be somewhat more difficult to detect than items buried for some time. This is primarily a metallurgi- cal phenomenon. Experiment with v arious detection modes, and pay close attention to both audio and TREASURE IMAGING signals as you scan.
HEADPHONE JACK The headphone jack is located at the rear of the battery pack under the armrest. Headphones are a v aluable accessory for an y metal detector to mask interfer- ence from outside noise. Headphones are particularly essential when hunting where noise (running water , people, surf , traffic, etc.
SEARCHCOILS Y our GTI 1500 is equipped with a 9.5" PRO formance imaging coil. Y ou may also wish to purchase a 12.5" imaging coil. Also a v ailable for the GTI 1500 are a 4.5" Sniper coil, a 10" x 14" DD coil and a 5x10" DD coil.
BATTERIES The GTI 1500 is equipped with two bat - tery packs, each holding four (4) standard AA batteries. (It is recommended that top quality hea vy duty or alkaline batteries be used. The detector is also designed to u t i l i z e n i c k e l m e t a l h y d r i d e ( N i M H ) rechargeable batteries.
Checking Condition Battery condition is reported continuously by the horizontal row of squares on the lower right side of the screen. Five are vis- ible when fully charged batteries are being used. When only one square remains, batteries should be changed.
3. Slip up the two cov ers on the battery panel and remove them completely . 4. T ake out the two battery holders (which are not connected by wire) by tilting the pack. (See image above.) 5. R emove the old batteries. 6. Install new batteries. Carefully observe polarity of the batteries and make certain the new batteries are aligned properly .
proper orientation. This is important! If an effort is made to install holders incorrectly , replacing the battery case covers will be difficult. If they are forced, damage to the detector can result. 8. Press down firmly and slide each cov er back in place.
RECOMMENDED ACCESSORIES Y our Garrett GTI 1500 represents the highest qualit y in metal detector manufac - turing. Complement it with quality acces- sories such as these from Garrett: • Headphones that will enable you to hear signals from the GTI more distinctly because they will mask other conflicting sounds from the environment.
MAINTENANCE • Always remember that y our GTI 1500 is a sensitive electronic instrument. It is built to withstand rugged treatment in the outdoors. Use your Garrett detector to the fullest extent possible, and never feel that you have to baby it. Y et, always protect the detector and handle it with reasonable care.
• When storing for a month or longer , remov e batteries from the detector and from their holders as well. Graphic T arget Imaging 1500 - 67.
SPECIALIZED HUNTING Coins Because of its unique discrimination and imaging capabilities, the GTI 1500 func- tions as an outstanding coin hunting detector , especially in its Coins mode.
cov er quantities of specific tr ash targets that are not being eliminated from detec- tion by factory-set discrimination. Y ou can then use the ACCEPT/REJECT touch pad to eliminate these pesky pieces of junk, no matter which mode you are using.
Relics R elics of all shapes and sizes can be found with a GTI 1500 when you hunt in its R elics mode. This mode is especially designed to eliminate those nuisance tar- gets most often encountered in relic hunt- ing.
Gold Stinger is recommended. It must be emphasized, however , that prospectors, when using the GTI 1500 or any other quality detector usually prefer to oper ate in the Z ero Discrimination detec- tion mode.
REPAIR SERVICE In case of difficulty , read this Owner's Manual again thoroughly to mak e certain your Garrett GTI 1500 is not inoper able because of wrong adjustments or improp- er operating methods. Y our dealer may also be able to offer advice.
• Y ou have checked with your dealer . • Y ou have tried to restore factory set - tings. • Y ou have carefully packed the detec- tor in its original shipping carton or other suitable box. Make certain that proper insulation or packing material is used to keep all parts secure.
post unless you give written authorization to ship collect by air parcel post, UPS Blue (air) or air freight. 74 - Garrett Metal Detectors.
RECOMMENDED READING Since your Garrett GTI 1500 is a truly universal detector , all of the RAM books will be pertinent to its use. Of particular interest, however , will be the revised ver - sion of G.
about One- T ouch detectors such as the GTI 2500. Y ou will also be interested in The New Successful Coin Hunting , filled with "how to" tips and success stories about coin hunting. Charles Garrett's pocket -sized, treasure- hunting field guides are also highly recom - mended.
Graphic T arget Imaging 1500 - 77 Please send me the following RAM books: (Please indicate number of copies desir ed.) ___ New Successful Coin Hunting ....................$9.95 ___ T r easur e Hunting for Fun and Pr ot .........$9.95 ___ T r easur e Caches Can Be Found .
78 - Garrett Metal Detectors MAIL-IN ORDER FORM Add $2.00 for rst book, and $1.00 for each additional book ordered (maximum $3.00) for handling and shipping char ges.
SPECIFICATIONS Detector T ype: V ery low Frequency , tr ans- mitter/receiver , T reasure Imaging and Gr aphic T arget Analyzer for precise target identification, multiple notch discrimina- tion. Controls: Easy access touch pads Display: High visibility LCD adjacent to touch pads; data accessible at any angle; backlight.
Battery Life: (Approximate) Alkaline: 25 hrs. Carbon Zinc: 18 hrs. NiMH: 20 hrs. Humidity: 0 to 95% Non-condensing T emperatures: Oper ating: 0 ˚ to 130 ˚ F . Stor age: -20 ˚ to 150 ˚ F . Construction: High strength glass-filled nylon with han- dle-mounted control/display panel.
MIND YOUR MANNERS Filling holes and obeying no trespassing signs are but two requirements of a dedi- cated metal detector hobbyist. A sincere request that Charles Garrett makes to every user of one of his detectors is that each place searched be left in a better condition than it w as found.
• I will not destroy property , buildings or the remains of ghost towns and other deserted structures. • I will not leave litter or uncovered items lying around.
TRADEMARKS / PATENTS GTI 1500, T reasureVision, Graphic T arget Analyzer and One T ouch are TM of Garrett Electronics, Inc. P atent Protection: Garrett's high tech instruments are pro - tected b y one or more of the following U.
WARNING! Any metal detector may discover under- ground power lines, explosiv es or other items which when struck could cause per- sonal injury . When searching for treasure with y our Garrett GTI 1500, observe these precautions: • Do not hunt in an area where you believe there ma y be shallowly buried under- ground electric lines or pipes.
Graphic T arget Imaging 1500 - 85.
Garrett Metal Detectors 1881 W . State Street Garland, T exas 75042 T : (972) 494-6151 F : (972) 494-1881 1.800.527.4011 (U.S.) sales@garrett.com www .
.
Garrett Metal Detectors. Copyright 2008 All Rights Reserved. 1524900.D.0408 TM.
Ein wichtiger Punkt beim Kauf des Geräts Garrett Metal Detector GTI 1500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Garrett Metal Detector GTI 1500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Garrett Metal Detector GTI 1500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Garrett Metal Detector GTI 1500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Garrett Metal Detector GTI 1500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Garrett Metal Detector GTI 1500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Garrett Metal Detector GTI 1500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Garrett Metal Detector GTI 1500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Garrett Metal Detector GTI 1500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
