Benutzeranleitung / Produktwartung SL40 des Produzenten Garmin
Zur Seite of 22
SL40 TM V H F C o m m p i l o t ’ s g u i d e.
© 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. Garmin A T 1200 East 151 st Street, Olathe, Kansas 66062, U.S.A. 2345 T urner Rd., SE Salem, OR 97302 T el. 913/397.8200 or 800/800.1020 T el. 503/581.8101 or 800/525.6726 Fax 913/397.
i Introduction Introduction W elcome ... W elcome to a new era of aviation communication. Once again, Garmin A T , Inc. has set new standards in features and ease of use for the general aviation public. The SL40 is a VHF Communications T ransceiver for use by the aviation pilot.
Introduction ii Contacting the F actory If the SL40 unit fails to operate despite troubleshooting ef forts, contact Garmin T echnical Support for assistance. GARMIN International, Inc. 1200 East 151st Street Olathe, KS 66062-3426 USA Phone: (913) 397-8200 F AX: (913) 397-8282 http://www .
iii Introduction T able of Contents W elcome ... ............................................................. i History of Revisions ................................................ i Ordering Information .............................................
iv Introduction This page intentionally left blank.
1 Getting Started Display Getting Started This guide describes the operation of the SL40 VHF Communication T ransceiver . Display The 1-line by 16-character display is composed of 5x7 dot matrix alphanumeric high intensity LEDs. A photocell is located in the top left corner of the front panel display .
2 Getting Started Annunciators Several annunciators are used to help indicate the operating modes of your SL40. The TX (T ransmit) annunciator is lighted whenever you are transmitting. If the avionics bus drops below 9 VDC, the SL40 will not transmit.
3 Getting Started EC (Emergency Channel) Press the EC button to load the Emer gency Channel (121.500 MHz) as the standby frequency . The Monitor function is automatically enabled. MON (Monitor) Press the MON button to listen to the standby frequency .
4 Getting Started Detailed Operation Detailed Operation This section introduces the basic operating details of the SL40 VHF Communications T ransceiver . P ower On/Off T ur n the Power/V olume control clockwise past the OFF detent. The SL40 may be installed to be powered fr om the avionics panel so the on/off contr ol will be disabled.
5 Detailed Operation Monitoring and Recalling F requencies Frequency Monitoring The Frequency Monitoring function allows you to listen to the Standby frequency , while monitoring the Active frequency for activity . Press the MON button to listen to the standby frequency .
6 Getting Started Detailed Operation 119.10 LST121.80 Viewing the Auto Stack List 119.10 MEM121.80 119.10 MEM124.55 Viewing User Stored Fr equencies 119.10 WTH162.40 Viewing W eather Frequencies 162.400 MHz 162.425 MHz 162.450 MHz 162.475 MHz 162.500 MHz 162.
7 Detailed Operation Removing a Frequency fr om User Memory Y ou may edit the contents of User memor y to remove its stor ed frequencies when you want to make a change or you receive a “MEM Full” message. 1. Press RCL . T urn the Large knob to the User (MEM) frequencies .
8 Getting Started Detailed Operation 6. Press MEM to save the displayed ID . T urn the Large knob to “Done” and press MEM . The alphanumeric ID for a frequency is displayed only when looking at user stored fr equencies using the recall (RCL) feature.
9 Detailed Operation System Functions System Functions The SL40 includes a number of System Functions that give you more information about your com- munication equipment. Press and hold the MON button for about three seconds to r each the System Function.
10 Getting Started Detailed Operation RFLvl 123 RF Level RF Level The RF Level function shows the relative signal strength of the fr equency you are listening to. The range displayed is between 0 and 255. The value will constantly change as you are viewing it as signal conditions change.
11 Detailed Operation Noise Level The Noise Level function shows the relative received noise level of the fr equency you are listening to. The range displayed is between 0 and 255. The value will constantly change as you are viewing it as signal conditions change.
12 Appendix Intcom Lvl 100 Intercom Level Sidton Lvl 100 Sidetone Level Lo Dsp Lvl 0 Low and High Display Levels Hi Dsp Lvl 50 Intercom Level This function adjusts the Intercom Audio Level. T urn the Small knob to change the value. The range is from 0 to 255.
13 Appendix Specifications SL40 Specifications Featur es 760 Communication Channels Frequency Range: 118 to 136.975 MHz Active and Standby Flip/Flop Frequencies V olume Control 16-Character High-Inte.
14 Appendix Accessories and P acking List T o obtain accessories for your SL40 please contact your Garmin dealer . Help us better support you by completing our on-line r egistration form today! Registration ensur es that you will be notified of pr oduct updates and new pr oducts and pr ovides lost or stolen unit tracking.
.
© 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151 st Street, Olathe, Kansas 66062, U.S.A. Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey , SO51 9DL, U.K. Garmin Corporation No. 68, Jangshu 2 nd Road, Shijr , T aipei County , T aiwan www .
Ein wichtiger Punkt beim Kauf des Geräts Garmin SL40 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Garmin SL40 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Garmin SL40 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Garmin SL40 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Garmin SL40 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Garmin SL40 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Garmin SL40 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Garmin SL40. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Garmin SL40 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.