Benutzeranleitung / Produktwartung 1270 des Produzenten Fisher
Zur Seite of 20
1270 Operating Manual Special Anniversary Edition Metal Detector FISHER RESEARCH LABORATORY.
CONTENTS About Your Detector ............................................................ pg. 1 Condensed Operating Instructions .................................. pg. 2 Setting Up ......................................................................
ABOUT YOUR FISHER 1270 The 1270 is a “motion” detector and was designed to offer you more versatility in a wide range of conditions: Highly mineralized soil, extremely trashy areas, and deep targets. By utilizing the various controls on the 1270, you will find more items that were unreachable until today.
2 Read this instruction manual thoroughly, practice often and you are in for some exciting treasure hunting. Drop us a line if you have any questions, comments or good finds to tell us about.
SETTING UP Your new 1270 comes ready to assemble and use, but first review the steps below before proceeding. STEP 1. Unpack your 1270 carefully, and save the carton: It may come in handy on the rare occasion that you may need service. STEP 2. The coil is attached to the lower stem.
STEP 6. When the stem length is properly adjusted, tighten the lower lock nut, and the coil wing nut. CAUTION: Never use a pliers or anything other than your hand to tighten either lock nut or wing nut. STEP 7. Disconnect the search-coil cable from the control housing and wrap it around the stem.
CONTROLS & FUNCTIONS 5 1. ON / OFF VOLUME: ON /OFF VOLUME: Allows you turn on the 1270 and adjust the volume to a comfortable level. No need to have a special headphone with volume controls.
6 7. IRON DISC TOGGLE: When this toggle switch is flipped ON, the 1270 will operate in IRON DISC mode. When operating in this mode, the IRON DISC control becomes ac- tive and the NORMAL DISC control will be ignored.
7 ALL METAL MODE Your 1270 gives you two ways to search in all-metal operation: (1) by set- ting your NORMAL DISC to 0, or (2) by turning on the ALL METAL GROUND ADJUST (rotate knob clockwise).
8 IRON DISC MODE metal. This may be tested quickly by pulling the trigger switch and sweep- ing over an area of about one square foot. If no signal is detected, release the trigger switch and raise the search coil off the ground, and lower it back down two or three times (also known as “bobbing”).
NORMAL DISC MODE When rejection of a full range of other non-ferrous trash is desired, the NORMAL DISC mode will be necessary. Make sure the ALL METAL GROUND ADJUST is OFF; that is, fully counterclockwise until it “clicks” into the “0” position.
SEARCH TECHNIQUES Good searching techniques are every bit as important as having a good detector. 1. Adjust your SENSITIVITY control. Only experience will tell you how to set it in every situation. As general rule, turn up the sensitivity to achieve maximum depth and detection of small items.
SEARCH TECHNIQUES NO- MOTION PINPOINT 1. When the target “beep” is heard, make an “X” over the target, as de- scribed above, to determine the target area. 2. Move the coil away from the target area, and lower the coil to the ground. 3. Pull, and hold the MODE TRIGGER switch.
TARGET RECOVERY Once you have pinpointed a target, your objective is to recover it quickly and neatly, leaving virtually no trace of your excavation. There are many ways do this, and you will soon discover which method works best for you. REMEMBER: Always leave the ground in the same condition as you found it.
A “False Signal” occurs when something sounds like a good target, but is not. Your 1270 does a great job of discriminating, but bad “targets” with similar electrical characteristics can fool it. Large pieces of trash or items very close to the search coil will occasionally sound “good”.
Your 1270 doesn’t require a lot of care, nor does it require regular “maintenance”. However, you should do a few things to keep your 1270 in peak operating condition. 1. Remove the batteries if you’re not going to be using your detector for a while.
Subject to improvement or modification without notice. SPECIFICATIONS 15 OUTPUTS BATTERIES BATTERY LIFE WEIGHT FREQUENCY LENGTH SEARCH COILS SEARCH MODES Low Battery Alert ...................................................... Automatic (LED) Built-i n Speak e r .
.
.
QUALITY Fisher detectors are renowned for their quality. Each detector is hand crafted in the USA with pride PERFORMANCE Treasure Hunters worldwide rely on Fisher. Our detectors are durable, dependable, and search deeper.. REPUTATION Fisher produced the first patented metal detector in 1931.
Ein wichtiger Punkt beim Kauf des Geräts Fisher 1270 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Fisher 1270 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Fisher 1270 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Fisher 1270 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Fisher 1270 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Fisher 1270 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Fisher 1270 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Fisher 1270. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Fisher 1270 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.