Benutzeranleitung / Produktwartung TID-320 des Produzenten Farenheit
Zur Seite of 25
TID-320/ TID-320T In-Dash 3.2” Monitor T ouch Sensor DVD/MP4/ CD MW/FM Radio Built-in NTSC tuner Owner’s Manual Take the time to read thro ugh this owner’s manual . Familiarity with installation and operation pr ocedure s will hel p you obtain the best Performance from your new DVD-receiver.
Page - 1 Table of Contents Table of Contents............ .................................... .................................... .......................... ....... ..1 Important Safeguards.............................. ..............................
Page -2 Important Safeguards z Using the device at temperature below -10 ℃ may cause the break age of the device. BEFORE USING PLEASE HEAT UP TH E PASSENGER COMPARTMENT TO THE RECOMM ENDED TEMPERATURE! z Read carefully through this manual to familiarize yourself with this high-quality sound sys tem.
Page - 3 Accessories Package contains the following accessories for instal lation and operation of t he unit. (1) W asher , S pring W asher , M5 Nut 1 each (2) Mounting S trap 1 (3) Screw 1 (4) Bolt 4.
Page -4 Installation/Un-Installation First complete the electrical connections, and then check them for correctness. Installation This unit can be installed in any dashboard having an opening as shown on the pictu re. The dashboard should be 4.75 – 5.
Page - 5 Wiring Connections Make sure you have good chassis ground. A good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the vehicle’s metal chassis.
Page -6 Detachable Control Panel Detaching the control panel z Turn the Power off. z Press OPEN button release the panel. z Pull the panel out. Attaching the co ntrol panel z Insert the left side of the control panel into the m ain unit. z Press the control panel right side until the “click” sound is heard.
Page - 7 Inner Panel 17. M emory Car d slot 18. Flash LED 19. RE SET 1. POWER/ MUTE 2. MODE 3. MENU 4. AS/PS 5. Volume Up (+) 6. NEXT 7. IR sensor 8. PREVIOUS 9. LCD 10. AV in jack 11. MEM/ 12. OK 13. OPEN 14. USB jack 15. BAND 16. Volume Down (-) 20.
Page -8 IR Remote Control REPLACIN G THE BA TTERY Remote Control comes with a CR-2025 Lithium Battery included. 1. Remove the Battery Holder from the back of the Remote Control. 2. Insert a CR-2025 Lithium battery with the positive (+) mark upward. Insert the Battery Holder into the back of the Remote Control.
Page - 9 General Opera tions Reset the Unit In case the unit is malfunctioned or need to reset to factory default setting, press RESET button in inner panel then the u nit will be reset. Power on/off Press “POWER” button to turn on the unit. Long press POWER button on front panel or press POWER button on RC to power off the unit.
Page - 10 Press / buttons on remote to adjust the audio setting data (or press the knob on front panel to adjust the setting data). Press SEL button on remote again to save the setting data and return to current mode. Notes: If turn off the power, all the settings of each mode will be saved.
Page - 11 z EXPERT MENU MENU DESCRIPTION DX Set search radio station by DX or LOCAL mode. DX → LOCAL STEREO Set radio audio at STEREO or MONO mode, STEREO → MONO BEEP Set press keys‘ sound.
Page - 12 Preset station 1-6 play and setting z Play preset station: to play the preset station 1-6, you can press number key 1-6 on remote control, Preset station setting: during manual t urning or a.
Page - 13 GOTO Functi on Long press AUDIO/GOTO button on remote control to show GOTO menu, use 0-9 to input tra ck/ time to go to directly. Fast Forward and Backward Press the / buttons and hol.
Page - 14 Changing the Subtitle La nguage (only for MP4 files) Press SUB-T button on the remote to select the pr eferred language for sub-title. ZOOM (only for MP4 files) Press ZOOM button and hold fo.
Page - 15 Picture file: JPEG (*.jpg) z ISO 9660 or IS O 9660 +Joliet format - Max. 30 characters z Max. Track number is 448 z Max. nested directory is 8 levels z The max. album number is 99 z The max. length of each track is 99 minutes 59 seconds z Supported sampling frequency for MP3 disc: 8 KHz to 4 8 (44.
Page - 16 Repeat playback Press the RPT/P.SCN button on the RC once or more times to repeat the playback: - For VCD/CD: display appears Repeat Track => Repeat Disc => Off (Some discs do not support this functions).
Page - 17 Selecti ng different audio modes z For DVD disc: press AUDIO on t he RC repeatedly to select the audio language to listen (if the disc supports multi-language mode). z For VCD disc: press AUDIO on the RC repeatedly to select the follo wing modes: L R STEREO (Channel left => Channel right => Stereo).
Page - 18 Notes on creating your o wn CD-R or CD-RW containing M P3 files: z To enjoy high quality sound, we recommend converting to MP 3 files with a sampling frequency of 44.1 kHz and a fixed bit rate o f 128 kbps. z DO NOT store more than 448 MP3 files per disc.
Page - 19 Channel Select this menu item is to set your desired searching channel, press cursor left/right buttons on remote control to select one. Fine Select this menu item is to fine TV picture and s ound until it achieves the best quality, press c ursor left/right buttons on remote control to adjust.
Page - 20 Rating For DVD discs which support rating system, setting up rating control can prevent children from watching content that might not be suitable to their age.
Page - 21 Video Setup: Brightness With this menu item you c an set up the brightness of the image. Contrast With this menu item you c an set up the contrast of the image. Hue With this menu item you c an set up the hue. Saturation With this menu item you c an set up the color saturation.
Page - 22 Note on Discs Only use groundless loudspeakers. Use only loudspeakers of minimal 40W att, using fewer watts may result in damaging your loud speakers at higher volumes. Use 4~8 Ω (Ohm impedance) loudspeakers only; using higher or lesser impedance may damage the unit.
Page - 23 T roubleshooting guide Symptom Cause Solution General No power The car ignition is not on. The fuse is blown. If the power supply is properly connected to the car accessory switch the ignition key to “ACC”. Replace the fuse. Disc Disc cannot be loaded.
Page - 24 Specification General Power supply: 12 V DC Current consumption: max. 10 A Maximum power output: 40W x 4 channels Compatible formats: DVD/SVCD/VCD/HDCD/MP3/MP4/WMA /CDDA/Picture-CD/ JPEG/ CD-R/ -RW/D VD±R/±RW playback Dimensions (W x D x H) / weight: 178 x 175 x 50 mm / 1.
Ein wichtiger Punkt beim Kauf des Geräts Farenheit TID-320 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Farenheit TID-320 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Farenheit TID-320 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Farenheit TID-320 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Farenheit TID-320 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Farenheit TID-320 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Farenheit TID-320 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Farenheit TID-320. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Farenheit TID-320 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
