Benutzeranleitung / Produktwartung SI 28 des Produzenten Extron electronic
Zur Seite of 16
User’s Guide Surface Mount Speakers 68-1164-01 Rev . A 11 06 SI 26 and SI 28.
SI 26 and SI 28 Speakers • Packaging Packaging Information P a r t N o . XX X-XX X -0 1 In s ta ll 2 0 6W C e iling Spe a k er 3 3 -X X X X - 0 1 R E V .
SI 26 and SI 28 Speakers • Introduction 1 About the SI 26 and SI 28 Speakers The Extron System I NTEGRA T OR ® SI 26 and SI 28 two-way surface mount speakers are ideally suited for classr ooms, conference rooms, and boar drooms. W ith a weather r esistant construction, they are also suitable for outdoor envir onments.
SI 26 and SI 28 Speakers • Features 2 Featur es Dimensions: SI 26 : 13.0" H x 8.5" W x 6.75" D (33.0 cm H x 21.6 cm W x 17.1 cm D) SI 28 : 16.
Installation Installing the SI 26 or SI 28 Speaker The SI 26 or SI 28 can be mounted on a surface, such as a wall or post, or mounted in a bookcase, or under a shelf, and can be used with any Extron pr oduct with power amps.
4 SI 26 and SI 28 Speakers • Installation Installation, cont’d shown in figure 5 and tighten the hex cap scr ew to lock the plate in position. This makes the next steps easier to perform. F asten the wall mount plate to the vertical surface (see step 7).
Cut access hole alongside stud and feed wires though hole. W all Stud W all Mount Assembly W all Approximate Stud line Behind Wall Bend wire to line up with access hole in plate. Hex Cap Screw Figure 7 — Install wall mount assembly N Extron r ecommends that the wiring installation be performed by a professional audio equipment installer .
Installation, cont’d 6 SI 26 and SI 28 Speakers • Installation 7. Place the wall mount assembly against the wall, aligning the plate holes with those drilled, and secure with appropriate har dware (see figur e 5), using a powered screwdriver with an appr opriate screw bit.
Seismic Safety Cab le Attach line here and secure. Anchor this end to a suitable secure point. Figure 10 — Attach a seismic safety cable to the rear of the speaker Mounting the SI 26 speaker onto the wall mount assembly 3 .
8 SI 26 and SI 28 Speakers • Installation Installation, cont’d Figure 12 — Hook the speaker over the edges of the V -lock groove on the wall mount assembly 3b . Rotate the speaker until the speaker box bracket left edge hooks over the left edge of the V -lock groove (see above).
3. T urn on the audio source and any associated devices. Follow the manufacturers instructions to adjust the sour ce and device settings as desired to get the optimum audio output for your speaker application. It may be necessary to adjust the angle of the speaker (see steps 5 and 6 below) to get the best audio coverage area for your application.
10 SI 26 and SI 28 Speakers • T roubleshooting Tips T roubleshooting Tips Service access In order to service the speaker it may be necessary to r emove the front grill. T o remove the grill: 1 . Carefully r emove the Extron logo, as described on page 9.
Observed Problem Possible Cause(s) Remedial Action 1 Speaker easily lifted from mount assembly . Locking hex cap screw not tightened enough. Following the steps on page 9, tighten the hex cap screw until it is not possible to remove the speaker . 2 No sound heard from speakers.
12 SI 26 and SI 28 Speakers • Specifications Audio/acoustic and electrical Speaker type ................................... 2-way , indoor/outdoor surface mount Frequency range ............................ SI 26 70 Hz to 20 kHz, -10 dB, half space SI 28 50 Hz to 20 kHz, -10 dB, half space Power capacity .
Extron’ s W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of five years from the date of pur chase.
© 2006 Extron Electronics. All rights reserved. Extron Electronics, U SA 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Extron Electronics, E urope Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.
Ein wichtiger Punkt beim Kauf des Geräts Extron electronic SI 28 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Extron electronic SI 28 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Extron electronic SI 28 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Extron electronic SI 28 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Extron electronic SI 28 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Extron electronic SI 28 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Extron electronic SI 28 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Extron electronic SI 28. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Extron electronic SI 28 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.