Benutzeranleitung / Produktwartung DVI DL 201 Rx des Produzenten Extron electronic
Zur Seite of 48
User ’s Manual Dual Link DVI T ransmitter and Receiver DVI DL 201 Tx/Rx 68-1531-01 Rev . B 12 08.
Pr ecautions This symbol is intended to alert the user of important opera ting and mainte nance (servici ng) inst ruction s in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.
安全须知 • 中文 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压,有触电危险。 .
.
DVI DL 201 Tx/Rx • Quick Start Guide QS-1 Quick Start Guide — DVI DL 201 Tx/Rx The DVI DL 201 Tx/Rx extends DVI-D signals up to 100' (30 m) at resolutions up to 2560x1600 @ 60 Hz, using twisted pair (TP) cable.
DVI DL 201 Tx/Rx • Quick Start Guide Quick Start Guide — DVI DL 201 Tx/Rx, cont’d QS-2 T o use DDC pass-through routed to the local monitor: a . Congure the DDC switches as shown in the gur e at right and described on page 3-4. b . Connect a source device to the transmitter .
i DVI DL 201 Tx/Rx • T able of Contents i Chapter One • Introduction .................................................... 1-1 About this Manual .................................................................... 1-2 About the DVI DL 201 Tx/Rx ...
ii DVI DL 201 Tx/Rx • T able of Contents T able of Contents, cont’d Chapter Three • Configuration and Operation ......... 3-1 Conguration .............................................................................. 3-2 Using the EDID Minder to read and stor e EDID from a displa .
DVI DL 201 Tx/Rx 1 Chapter One Intr oduction About this Manual About the DVI DL 201 Tx/Rx DVI DL 201 Tx/Rx Features.
DVI DL 201 Tx/Rx • Introduction Intr oduction About this Manual This manual contains information about the DVI DL 201 Tx/Rx signal transmitter and receiver , with information on how to mount, install, and operate these units.
DVI DL 201 Tx/Rx • Introduction 1-3 EDID Minder — The EDID Minder maintains continuous EDID (Extended Display Identication Data) communication with the attached source. This ensur es that the DVI source powers up correctly and maintains a pr oper video output, even if the display is off.
DVI DL 201 Tx/Rx • Introduction Introduction, cont’d 1-4.
DVI DL 201 Tx/Rx 2 Chapter T wo Installation Mounting the DVI DL 201 Tx/Rx Panel Features Cable Connections and Switches.
DVI DL 201 Tx/Rx • Installation Installation Mounting the DVI DL 201 Tx/Rx The transmitter is 1U high, a half rack wide and 3" deep, for easy rack mounting near the source device. The receiver is 1" high, a quarter rack wide and 3" deep, allowing multiple mounting options near the display device.
DVI DL 201 Tx/Rx • Installation Rack mounting procedur es The unit can be mounted in the front or r ear of: RSU 126 (6" deep 1U universal rack shelf kit: PN • 60-190-10 ) RSB 126 (6" deep 1U basic rack shelf: PN • 60-604-10 ) RSU 129 (9.
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-4 Under -desk mounting The gure below shows how to mount the DVI DL 201 Tx under a desk or podium, using the optional Extron MBU 123 under desk mounting kit (PN 70-212-01 ).
DVI DL 201 Tx/Rx • Installation 2-5 Through-desk mounting The DVI DL 201 Tx should not be mounted through a desk. T o mount the DVI DL 201 Rx thr ough a desk or podium, use the optional Extron MBD 129 thr ough-desk mounting kit (PN 70-077-02 ), and follow these instructions: 1 .
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-6 Pole mounting The instructions for mounting the receiver on the pr ojector pole, using the PMK 300 pole mounting kit (PN 70-374-01 ), are shown below . For instructions on using any other Extron projector mounting kit, consult the appropriate user guide.
DVI DL 201 Tx/Rx • Installation 2-7 N On the side mounting plates, the device is typically mounted on the outside of the bracket. On the front mounting plate, the device is mounted on the inside of the bracket. a . Use the two 4-40 x 3/16" screws (provided) to secure the receiver to the bracket b .
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-8 Panel Features DVI DL 201 Tx front panel featur es The illustration below shows the front panel featur es of the DVI DL 201 Tx.
DVI DL 201 Tx/Rx • Installation 2-9 DVI DL 201 Tx rear panel featur es The illustration below shows the rear panel featur es of the DVI DL 201 Tx. 12V 0.
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-10 DVI DL 201 Rx front panel featur es The illustration below shows the front panel featur es of the DVI DL 201 Rx.
DVI DL 201 Tx/Rx • Installation 2-11 DVI DL 201 Rx rear panel featur es The illustration below shows the rear panel featur es of the DVI DL 201 Rx. POWER 12V 0.
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-12 Cable Connections and Switches DVI-D input Connect the DVI-D source device to the female DVI-I input connector . The dual link DVI-D input carries a signal with a resolution up to 2560x1600 @ 60 Hz.
DVI DL 201 Tx/Rx • Installation 2-13 Pin Signal 1 TMDS data 2– TMDS data 2+ TMDS data 1– TMDS data 1+ DDC clock +5 V power DDC data TMDS clock+ Ground CEC control* TMDS clock– Hot plug detect .
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-14 T wisted pair output/input T erminating shielded cable CA T 5/5e/6/7 twisted pair cable is not provided with the transmitter/receiver pair .
DVI DL 201 Tx/Rx • Installation 2-15 Pin # TIA/EIA T 586 A Wire color TIA/EIA T 586 B Wire color Cable 1 Cable 2 Cable 3 1 White-green White-orange Data 0+ CEC Data 3+ 2 Green Orange Data 0+ HPD Dat.
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-16 Single Link/Dual Link DVI Dual Link DVI carries signals at resolutions up to 2560x1600 @ 60 Hz.
DVI DL 201 Tx/Rx • Installation 2-17 DDC switches When the DVI-D source device boots up, it uses the Display Data Channel (DDC), a two-way communication protocol, to obtain Extended Display Identication Data (EDID) from the display device. This allows the source to output a r esolution that matches the capabilities of the display .
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-18 Control pass-thr ough The DVI DL 201 Tx/Rx cannot be controlled by RS-232 or IR contr ols. However , they are able to pass signals from a contr ol device to a remote device that is controlled by those signals.
DVI DL 201 Tx/Rx • Installation 2-19 RS-232 signals RS-232 signals are bidir ectional — signals pass from the contr ol device and replies r eturn from the r emote device.
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-20 Power input 1 . Connect the captive screw connector from the supplied 12 VDC power supply into the power receptacle.
DVI DL 201 Tx/Rx 3 Chapter Thr ee Configuration and Operation Configuration Setup and Operation T roubleshooting.
DVI DL 201 Tx/Rx • Conguration and Operation Configuration and Operation Configuration Using the EDID Minder to read and stor e EDID from a display During boot up, the DVI-D source device uses Display Data Channel (DDC) to obtain Extended Display Identication Data (EDID) from the display device.
DVI DL 201 Tx/Rx • Conguration and Operation 10 . Power up the transmitter and the receiver . A single power supply can provide power to both units thr ough the remote power connection. 11 . Connect the r emote display to the receiver output. A local monitor display can also be connected to the transmitter output at this time.
DVI DL 201 Tx/Rx • Conguration and Operation Configuration and Operation, cont’d 3-4 Using pass-through mode with DDC r outed to a local monitor 1 . Set the EDID Minder switch to the off (down) position and the Default EDID switch to the off (down) position (see the gur e at right).
DVI DL 201 Tx/Rx • Conguration and Operation 3-5 Using pass-through mode with DDC r outed to the remote display N This is the factory default setting. N Although DDC can be routed to the remote display , there may be instances when the signals become corrupted or weak.
DVI DL 201 Tx/Rx • Conguration and Operation Configuration and Operation, cont’d 3-6 Setup 1 . Determine which source will be used for the EDID information and congure the DDC switches appr opriately (see pages 3-2 to 3-5). If necessary , use the EDID Minder to read and stor e information from a display (see pages 3-2 to 3-3).
DVI DL 201 Tx/Rx • Conguration and Operation 3-7 Insure all thr ee twisted pair cables are rmly seated in the correct r eceptacles. No output signal or poor quality signal — Check the integrity of the UTP or STP cables between the transmitter and the receiver .
DVI DL 201 Tx/Rx • Conguration and Operation Configuration and Operation, cont’d 3-8 Display device displays a flashing black or blue screen, snow , or other distortion — A device that is not High-Bandwidth Digital Content Protection (HDCP) compliant may be r eceiving HDCP-encrypted signals.
DVI DL 201 Tx/Rx A Appendix A Refer ence Information Specifications Included Parts Optional Accessories.
DVI DL 201 Tx/Rx • Reference Information Refer ence Information A-2 Specifications Video Maximum data rate....................... 10 Gbps (3.3 Gbps per color) Maximum pixel clock ................... 330 MHz (165 MHz per link) Resolution range .....
DVI DL 201 Tx/Rx • Reference Information A-3 Video output — r eceiver Number/signal type ..................... 1 dual link DVI-D N Dual link DVI is backwards compatible with all single link DVI/HDMI signals. Connectors ............................
DVI DL 201 Tx/Rx • Reference Information Refer ence Information A-4 Cooling ........................................... Convection, no vents Mounting Rack mount .
DVI DL 201 Tx/Rx • Reference Information Included Parts Included parts Replacement part number (1 pair) DVI DL 201 Tx/Rx 60-957-01 or (1) DVI DL 201 Tx 60-957-12 or (1) DVI DL 201 Rx 60-957-13 (1) 12 VDC, 2A power supply DVI DL 201 Tx/Rx User's Manual Optional Accessories Accessory Part number RSF 123 (3.
DVI DL 201 Tx/Rx • Reference Information Refer ence Information A-6.
Extron’ s W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of three years fr om the date of purchase.
© 2008 Extron Electronics. All rights reserved. Ex tron US A - We st Headquar te rs + 80 0.6 33 .9 87 6 I nside US A / Ca nada On ly +1 .7 1 4.4 91 .1 50 0 +1 .7 1 4.4 91 .1 51 7 FA X Ex tron US A - East + 800 .6 33 .9 87 6 I nside US A / Ca nada On ly +1 .
Ein wichtiger Punkt beim Kauf des Geräts Extron electronic DVI DL 201 Rx (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Extron electronic DVI DL 201 Rx noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Extron electronic DVI DL 201 Rx - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Extron electronic DVI DL 201 Rx reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Extron electronic DVI DL 201 Rx erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Extron electronic DVI DL 201 Rx besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Extron electronic DVI DL 201 Rx verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Extron electronic DVI DL 201 Rx. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Extron electronic DVI DL 201 Rx gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.