Benutzeranleitung / Produktwartung 86251-08 des Produzenten Allied Telesis
Zur Seite of 78
Simply connecting the world Patch Release Note Patch 86251-08 For Rapier Series Switches Intr oduction This patch rel ease note lists the issues addres sed and enhancements made in patch 86251-08 for Software Release 2.5. 1 on existing models of Rapier L3 managed switches.
2 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Some of the issues addresse d in this Re lease Note include a level number .
Patch 86251-08 For Rapier Series Swit ches 3 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I A fanAndPsRedundantFanT rap message was sent fr om a Rapier when the RPS (Redundant Power Supply) was turned on o r off, even though Rapiers do not monitor the r e dundant fan stat us.
4 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I ISAKMP debug messages now corr ectly output IPv6 addres ses when using IPv6, and IPv4 addr esses when using IPv4. The IP version of packets was not bein g checked, so an IPv4 packet could match an IPv6 IPSec policy .
Patch 86251-08 For Rapier Series Swit ches 5 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I The SMTP proxy did no t corr ectly filter sessions wher e messages wer e fragmented. This had the potential to prevent the d etection of third-party relay attack s.
6 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I BGP did not always send With dr a wn advertisements when a route went down.
Patch 86251-08 For Rapier Series Swit ches 7 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I The warning given when a QoS policy is active on a port operating at reduce d speed has been changed to reflect the pr oblem more accurately .
8 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I When the device received a version 1 Query packet, it become a non-querier on that interface, even if it should have remained as the querier . This issue has been re solved.
Patch 86251-08 For Rapier Series Swit ches 9 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I OSPF disabled RIP unless RIP was activated using the SET OSPF RIP command. This issue has been r esolved. Running the PURGE IP command with a multicast ad dress and multiple sources was causing a fatal error .
10 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I F i l e s u s e d d u r i n g s t a r t u p w e r e b a c k e d u p f ro m NV S t o F L A S H e v e n i f t h e y were alr eady present in FLASH. This used up FLASH memory unnecessarily .
Patch 86251-08 For Rapier Series Swit ches 11 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I An additional check has been added for unknown GBIC models to determine if they ar e copper or fibre. A fatal error occurred w hen IPv6 fragmented a packet.
12 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I PIM SM did not establish a BSR cand idate between two AR720 routers with PPP over SYN.
Patch 86251-08 For Rapier Series Swit ches 13 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I An ETH interface was sometimes shown as Up in the output of the SHOW INTERF ACE command when it was actually Down . This issue has been res ol v ed .
14 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I DHEXPONENTLENGTH parameter in the CREA TE ISAKMP POLICY command was not accepted when creati ng ISAKMP policies that used IPv6.
Patch 86251-08 For Rapier Series Swit ches 15 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I DISABLE SWITCH PORT= port-list FLOW=PA USE DISABLE SWITCH PORT=ALL FLOW={JAMMING |PAUSE}[,...] ENABLE SWITCH PORT={ port-list |ALL} ENABLE SWITCH PORT= port-list FLOW=PAU SE ENABLE SWITCH PORT=ALL FLOW={JAMMING| PAUSE}[,.
16 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I IPv6 tunnelling over IPv4 failed if an IPv4 interface was not configur ed, even though an IPv4 interface is not needed for IPv6 tunnelling. This issue has been re solved.
Patch 86251-08 For Rapier Series Swit ches 17 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I OSPF disabled RIP unless RIP was activated using the SET OSPF RIP command. This issue has been r esolved. Occasionally the TCP connection was terminated early during an IDENT proxy TCP session.
18 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I The command ADD IPV6 6TO4 IP did not allow mor e than one tunnel.
Patch 86251-08 For Rapier Series Swit ches 19 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I A problem existed in a configuration with a single policy involving one private interface and two On Demand PPP public interfaces with NA T acting on traffic fr om the private to each of the public interfaces.
20 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I The IP route filter d id not always wo rk correctly for OSPF . This issue has been resolved. Zmodem uploads to some terminal emulators did not succeed because the 16-bit checksum was incorrect.
Patch 86251-08 For Rapier Series Swit ches 21 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I When a Finisar 8521 GBIC was used in an A T -A4 2/GBIC uplink module the link LED did not correctly show the link status. This is sue has been res ol v ed .
22 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I If th e fi re wa l l re ce i ve d a p a ck e t w i th an incorrect TCP checks um and ACK number , the packet was sent to the clie nt. Such packets are now r ejected by the firewall.
Patch 86251-08 For Rapier Series Swit ches 23 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I When changing from RSTP to STP mode, the STPCOMP A TIBLE option for the RSTP TYPE parameter incorrectly appear ed in the dynamic configuration.
24 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I An unkown interface log message was returned for VRRP if there was an interface UP or interface DOWN ev ent due to a mismatch between a monitor ed interface index and the corr esponding interface instance.
Patch 86251-08 For Rapier Series Swit ches 25 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I Featur es in 86251-05 Patch file details are listed in T able 4: Patch 86251-05 includes all issues reso lved and e nhancem ents released in previous patch es for Software Release 2.
26 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Under some circumstances, ISAKMP suf fer ed a fatal error if more than 8 SA proposals w ere pr esented.
Patch 86251-08 For Rapier Series Swit ches 27 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I IP routes deleted fr om the route cache o ccasionally caused a fatal error . This issue has been r esolved. The reconnection to the stream printing TCP port failed after a single successful connection was made .
28 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I STP settings were not r eta ined when a port was deleted from the VLAN that the STP belongs to.
Patch 86251-08 For Rapier Series Swit ches 29 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I A VLAN interface receiving a PIM Prune message on a port stopped forwar ding multicas t data to tha t port too early .
30 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I The SMTP proxy did not correctly allow outgoing (private to public) SMTP sessions when the DIRECTION parameter was set to OUT or BOTH in the ADD FIREW ALL PROXY command.
Patch 86251-08 For Rapier Series Swit ches 31 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I DHCP was offer ing network and br oadcas t addr esses to clients. This issue has been re solved. An error wa s not re turned if the SET F IREW ALL POLICY RULE command was executed with PROT OCOL=1 when ICMP forwarding was turned on.
32 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Featur es in 86251-04 Patch file details are listed in T able 5: Patch 86251-04 includes all issues reso lved and e nhancem ents released in previous patch es for Software Release 2.
Patch 86251-08 For Rapier Series Swit ches 33 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I OSPF and RIP Hello packets were being sent out all trunked ports. Now these Hello packets ar e only sent out the master port of the trunked gr oup.
34 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I The SHOW IP INTERF ACE command was showing ETH interfaces as up at startup, when SHOW INTERF ACE and SHOW ETH ST A TE had them as down. This issue has been resolved.
Patch 86251-08 For Rapier Series Swit ches 35 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I An additional check has been added to validate the MASK specified in an ADD IP ROUTE command. The check test s that the mask is contiguous. The SHOW CONFIG=ACC command was not showing the rscript file.
36 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Duplicate Addres s Detection (DAD) was not sent on VLAN interfaces. This issue has been r esolved. If all 32 VLAN interfaces had IP a ddresses attached, only 31 VLANs could be multihomed.
Patch 86251-08 For Rapier Series Swit ches 37 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I The following is sues with DHCP have been r esolved: • DHCP assigned an incorr ect IP address to clients shif ting fr om a rela yed to a non-relayed range.
38 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I The PURGE IP command did not remove ENABLE IP IGMP from the configuration. This issue has been r esolved. IGMP queries were being sent after IG MP was disabled. This issue has been res ol v ed .
Patch 86251-08 For Rapier Series Swit ches 39 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I The firewall doubled the IPSPOOF event timeout from 2 minutes to 4 minutes. This issue has been r esolved. MLD did not re spond corr ectly when it was in exclude mode and it r eceived a request block.
40 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I W h e n a d d i n g s t a t i c r o u t e s w i t h t h e A D D IP R O U T E c o m m a n d , t h e o r d e r o f the route in the route table was the r everse of the or der entered.
Patch 86251-08 For Rapier Series Swit ches 41 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I A log message is now cr eated when a user is for ced to logout from an asynchronous port when another user (i.e. someone connected via T elnet) resets the asynchr onous connection with the RESET ASYN command.
42 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I The MRU parameter in the SET PPP co mmand was incorr ectly handled as an interface parameter when the configu ration script was generated. This meant that the OVER parameter was omitted.
Patch 86251-08 For Rapier Series Swit ches 43 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I The following issues with IPv6 have been resolved: • Incorre ct default values wer e set for the PREFERRED and V ALID parameters in the ADD IPV6 PPFEFIX command.
44 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Wh e n m o re t ha n tw o f i rew a ll p ol ic i es wer e configured, an unexpected switch re start sometimes occurr ed.
Patch 86251-08 For Rapier Series Swit ches 45 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I When the TX cable was unplugged fr om a fibre port the operating s tatus was incorr ectly reported as UP .
46 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I When OSPF was enabled on startup, an OSPF interface would sometimes stay in the DOWN state. This issue has been r esolved. When ports were added to a trunk grou p on a Rapier 16, the ports operated in the wr ong duplex mode.
Patch 86251-08 For Rapier Series Swit ches 47 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I The ADD IPV6 HOST command was not accepting the INTERF ACE parameter when adding a host with a link-local addr ess. This issue has been res ol v ed .
48 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Router Advertisement Messages A router advertisement is an ICMP (type 10) message containing: ■ In the destination addr ess field of the IP header , the interface's configured advertisement address , either 2 24.
Patch 86251-08 For Rapier Series Swit ches 49 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I routers on the same link. By default th e minimum is 450 seconds (7 .
50 Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I this value. If it should never be used as a default router , set it to NOTDEF AUL T . ADD IP INTERFACE= interface IPADDRESS={ ipadd |DHCP} PREFERENCELEVEL={-2147483648.
Patch 86251-08 For Rapier Series Switches ADD IP ADVERTISE INTERF ACE 51 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I ENABLE IP ADVER TISE Syntax ENABLE IP ADVERTISE Description This command globally enables IC MP Router Discovery advertisements on the rout er.
52 DELETE IP ADVERTISE IN TERFACE Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Description This command adds ICMP Router Di scovery advertising to a single phys ical IP interface. The interface will only send router advertisements if it has been globally enabled with the ENABLE IP ADVER TISE comm and.
Patch 86251-08 For Rapier Series Sw itches SET IP ADVERTISE INTERF ACE 53 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I Example T o delete Router Discovery from vlan1, use the comman.
54 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I See Also DISABLE IP DISCOVER Y DELETE IP DISCOVER Y INTERF ACE ENABLE IP DISCOVER Y ADD IP DISCO.
Patch 86251-08 For Rapier Series S witches SHOW IP ADVE RTISE 55 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I See Also DISABLE IP DISCOVER Y DELETE IP DISCOVER Y INTERF ACE ENABLE I.
56 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Adopting the VRRP IP Addr ess Benefits The VRRP master router can adopt the IP addr ess of the v.
Patch 86251-08 For Rapier Series S witches SHOW IP ADVE RTISE 57 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I The ADOP TVRIP parameter specifies that when the switch is acting as the VRRP master it should r espond to requests dir ected at any IP address that it is backing up, even if it does not own that addr ess.
58 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Note that IPv6 mu lticast packets wi ll flood the VLAN w hen MLD snooping is disabled.
Patch 86251-08 For Rapier Series S witches SHOW IP ADVE RTISE 59 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I T o create a polling instance, use the command: ADD PING POLL= poll-id IPADDRESS={ ipadd | ipv6add [% inter face ]} [CRITICALINTERVAL=1.
60 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I After you have configur ed the ping polling instance, specify a scri pt or scripts to run when the device becomes unr eachable, using the command: CREATE TRIGGER= trigger-id MODULE=PIN G EVENT=DEVICEDOWN POLL= poll-id SCRIPT= filename .
Patch 86251-08 For Rapier Series S witches SHOW IP ADVE RTISE 61 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I Commands This enhancement intr oduces three new commands: ■ DISABLE I.
62 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I SHOW IP ICMPREPL Y Syntax SHOW IP ICMPREPLY Description This command display the status of confi.
Patch 86251-08 For Rapier Series S witches SHOW IP ADVE RTISE 63 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I Figure 6: Forwarding multicast dat a over a specified interface and port. Configuration Example The following configuration exam ple illustrates the st eps requir ed to create a static IGMP association.
64 SHOW IP IGMP Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Commands This enhancement modifies one command: ■ SHOW IP IGMP This command now includes a DESTINA TION parameter . Only the modified parts of the command text ar e shown below .
Patch 86251-08 For Rapier Series Swit ches SHOW IP IGMP 65 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I Figure 7: Example output fr om the SHOW IP IG MP DESTINA TION command showin g Static Gr oups.
66 ADD IP IGMP DESTINA TION Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I New Commands ADD IP IGMP DESTINA TION Syntax ADD IP IGMP DESTINATION= ipaddress INTERFACE= interface PORT={ALL| port-list } where: ■ ipaddress is an existing IGMP group destination address.
Patch 86251-08 For Rapier Series Sw itches CREA TE IP IGMP DESTINA TION 67 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I CREA TE IP IGMP DESTINA TION Syntax CREATE IP IGMP DESTINATION= ipaddress INTERFACE= interface [PORT={ALL| port-list }] where: ■ ipaddress is an exis ting IGMP gr oup dest ination address.
68 DELETE IP IGMP DESTINA TION Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I DELETE IP IGMP DESTINA TION Syntax DELETE IP IGMP DESTINATION= ipaddress INTERFACE= interface PORT={ALL| port-list } where: ■ ipaddress is an existing IGMP group destination address.
Patch 86251-08 For Rapier Series Swit ches ENABLE IP IGMP DEBUG 69 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I DISABLE IP IGMP DEBUG Syntax DISABLE IP IGMP DEBUG Description This c.
70 SHOW IP IGMP DEBUG Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I SHOW IP IGMP DEBUG Syntax SHOW IP IGMP DEBUG Description This command shows the IGMP debugging options that have be en set. Figure 8: Example output fr om SHOW IP IGMP DEBUG.
Patch 86251-08 For Rapier Series Swit ches SHOW IP IGMP DEBUG 71 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I ■ software r elease 86s-251 and patch 86251-04 are loaded, but the patch was corrupted after a restart or r eboot. The Rapier16f i requir es the 86251-04 patch to operate correctly .
72 SHOW IP IGMP DEBUG Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I Although the ifIndex and Interface numbers do not match, this is the c orrect port map . Y ou do not need to take any more acti on if you have the corr ect port map.
Patch 86251-08 For Rapier Series Swit ches SHOW IP IGMP DEBUG 73 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I Figure 3: Router startup messa ges Enter [Y] when the Force EPROM download (Y)? option appears. 11. Load the 86251-04.paz patch file, and set it as the pr eferred patch.
74 ADD PPP Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I ADD PPP Syntax ADD PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number , from 0 to 51 1.
Patch 86251-08 For Rapier Se ries Switches CREA TE PPP 75 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I CREA TE PPP Syntax CREATE PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number , from 0 to 51 1.
76 DELETE PPP Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I DELETE PPP Syntax DELETE PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number , from 0 to 51 1.
Patch 86251-08 For Rapier Series Swit ches SHOW PPP 77 Patch 86251-08 for Software R elease 2.5.1 C613-10356 -00 REV I Description This command is used to change the configuration parameters of a PPP .
78 SHOW PPP Patch Release Note Patch 86251-08 for Software R elease 2.5.1 C613-10356- 00 REV I.
Ein wichtiger Punkt beim Kauf des Geräts Allied Telesis 86251-08 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Allied Telesis 86251-08 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Allied Telesis 86251-08 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Allied Telesis 86251-08 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Allied Telesis 86251-08 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Allied Telesis 86251-08 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Allied Telesis 86251-08 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Allied Telesis 86251-08. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Allied Telesis 86251-08 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
