Benutzeranleitung / Produktwartung True Day/Night Indoor Vandal Color Camera ED550 des Produzenten EverFocus
Zur Seite of 26
EVERFOCUS 560 TVL T rue Day/Night Indoor V andal Color Camera Operation Instructions Model No. ED550 Please read this manual first for correct installation and operati on. This manual sh ould be reta ined for futu re reference. The information in this manual was current when publish ed.
- 2 - T ABLE OF CONTENTS 1. PRODUCT OVER VIEW ...................................................................................................... 4 1.1 Main Features ..................................................................................
- 3 - 5.8.7 SHARPNESS ............................................................................................................... ......................... 24 5.8.8 RESET ............................................................................
- 4 - 1. PRODUCT OVER VIEW The new ED550 camera is designed with adva nced new generation 16-bit DSP which has powerful processing capability to show over 5 6 0TVL horizontal re solution. Built-in DNR (Dynamic Noise Reduction) function, the ca mera perform s clear & crispe r image in low light and substantial disk -saving ef fect.
- 5 - 1.3 Specifications Pickup Device 1/3'' SONY Super HAD CCD Video Format NTSC or PAL Scanning System NTSC: 525 TV lines, 60 fields/sec PAL: 625 TV lines, 50 fields/sec Picture Elements 768 x 494 (NTSC) ; 752 x 582 (PAL) Horizontal Resolution 560 TVL Sensitivity 0.
- 6 - 1.4 Dimensions 2. NAMES AND FUNCTIONS OF P AR TS 2.1 Fr ont Panel Note: Internal Sensor is a Day/Night Switch Sensor . Internal Sensor.
- 7 -.
- 8 - 2.2 Back Panel (1) Power Input T erminal & V ideo Output Connector Connect to the appropriate power to each mode l. V ideo Output connector is for connecting the video output of the camera to a color monitor or other video devices through a 75 Ohm type coaxial cable with BNC female c onnector at backside of the camera.
- 9 - 3. INST ALLA TION T ake off camera's cover first. Fix 3 screws of th e bracket firm ly to wall or ceiling. Adjust the camera to best angle for viewing. Use the tact switcher at the back panel to make any adjustment if needed. Finally , place the cover back to the camera.
- 10 - 4. CAMERA SETUP OPERA TIONS This camera utilizes an On Scr een Display (OSD) user setup menu. 4.1 Setup Button T o set items on the user setup menu, use the following switch on the back panel. z Up: Adjust the switch to move the cursor upwards.
- 1 1 - 4.2 Display/Close the user setup menu scr een I. Press the SET button The menu screen will appear on the monitor as the block shown above. II. Using the cursor sw itch Adjust the switch c or d to move the cursor up or down. Move the switch e or f to adjust the mode or parameter of settings.
- 12 - 5. USER SETUP 5.1 Lens 1. When the SETUP menu is displa yed on the screen, please dire ct the arrow to poin t to “LENS” by adjusting the switch to UP or DOWN direction. 2. Please press SET button if you would lik e to return to the previous menu.
- 13 - Ö ESC: The shutter speed can autom atically be controlled. When ESC mode turns on, the auto control of the shutter speed can be perf ormed according to the brightn ess of the screen. The range of ESC is 1 ~ 70. Ö Manual: Please select “MANU AL” if you would like to cont rol the shutter manually .
- 14 - 5.3 White Balance Contr ol The screen color can be adjusted by using the WHITE BALANCE function. 1. Please direct the arrow to point to “WHI TE BAL” on the SETUP m enu by adjusting the switch to UP or DOW N direction. 2. Please select the mode you would like to ope rate by adjusting the switch to LEFT or RIGHT direction.
- 15 - 5.4 Backlight Even there is a massive backlight behind the obj ect, bright im ages of the background and the object can still be obtained by us ing the BACKLIGHT function. 1. Please direct the arrow to point to “BACKLIGHT” on the SETUP menu by adjusting the switch to UP or DOW N direction.
- 16 - 5.6 DNR (Dynamic Noise Reduction) Dynamic Noise Reduction in video images has the following ef fects. 1. Images are brighter and sharper . 2. When the level of noise is reduced, the pe rformance of a cam era can apparently be improved. 3. When it is recorded digitally , reduced noise can reduce image file size.
- 17 - Ö OFF: The function is disabled. 2. Press SET button when you finish all the settings. 5.8 Special 1. Please direct the arrow to point to “SPE CIAL” on the SETUP m enu by adjusting the switch to UP or DOW N direction. 2. Select the mode you would like to operate by adjusting the switch to LEFT or RIGHT direction.
- 18 - 5.8.1 CAMERA ID Input the camera ID, and it will be appeared on the monitor . 1) Please direct the arrow to point to “CAMERA” by adju sting the switch to UP or DOWN direction. 2) Select “ON” by adjusting the swit ch to LEFT or RIGHT direction.
- 19 - 5.8.2 COLOR ADJ Adjust the Color Gain from 0 ~ 15 5.8.3 SYNC There are two SYNCHRONIZA T ION modes: INTERNAL and EXTERNAL LINE-LOCK. In LINE-LOCK mode, w ithout a synchronous generator , it synchronizes the video signal between cam eras. The Line-Lock synchronization is only used in the places of 60Hz (N TSC models) or 50Hz (P AL models).
- 20 - z Please select the area you would like to detect from the 4 areas in AREA SEL m ode. z Please select ON mode for the chosen area. z Please adjust the switch to UP or DOWN direction to move between T OP , DOWN, LEFT and RIGHT for adjusting the size of the area to be detected.
- 21 - 2. Increase DOWN scale value by 20. AREA1 pos ition after change is: T OP: 10, DOWN: 45, LEFT : 20 and RIGHT : 40. 3. Increase TO P scale value by 20. AREA1 positio n after change is: T OP: 30, DOWN: 45, LEFT : 20 and RIGHT : 40. 4. Increase RIGHT scale value by 20.
- 22 - 5.8.5 PRIV ACY This mode covers the areas you do not want to see on the screen. 1) Please direct the arrow to point to “PRIV ACY” by adjusting the switch to UP or DOWN direction. 2) Select “ON” by adjusting the swit ch to LEFT or RIGHT direction.
- 23 - 1. The original position of AREA1 was T OP: 10, DOWN: 25, LEFT : 20 and RIGHT : 40. 2. Increase DOWN scale value by 20. AREA1 pos ition after change is: T OP: 10, DOWN: 45, LEFT : 20 and RIGHT : 40. 3. Increase TO P scale value by 20. AREA1 positio n after change is: T OP: 30, DOWN: 45, LEFT : 20 and RIGHT : 40.
- 24 - z In order to save the changes and comple te the setting, press the SET button. This allows you to return to the previous menu. 5.8.6 MIRROR -ON: Sets a horizontal image inversion. -OFF: Disable the inversion. 5.8.7 SHARPNESS The contour of the video image becomes clean er and m ore distinguishing as the level of SHARPNESS increases.
- 25 - 5.8.9 RETURN It saves all settings in SPECIAL m e nu and returns to the SETUP menu. 5.9 Exit Save all the setting menus and exit. SPECIAL C A M E R A I D O F F COLOR ADJ.
- 26 - EverFocus Electronics Corp. Head Office: 12F , No.79 Sec. 1 Shin-T ai W u Road, Hsi-Chih, T aipei, T aiwan TEL: +886-2-26982334 F AX: +886-2 -269 823 80 www .eve rfocus.com.tw USA L.A. Office: 1801 Highland A ve. Unit A Duarte, CA 9 1010, U.S.A.
Ein wichtiger Punkt beim Kauf des Geräts EverFocus True Day/Night Indoor Vandal Color Camera ED550 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie EverFocus True Day/Night Indoor Vandal Color Camera ED550 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für EverFocus True Day/Night Indoor Vandal Color Camera ED550 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von EverFocus True Day/Night Indoor Vandal Color Camera ED550 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über EverFocus True Day/Night Indoor Vandal Color Camera ED550 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon EverFocus True Day/Night Indoor Vandal Color Camera ED550 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von EverFocus True Day/Night Indoor Vandal Color Camera ED550 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit EverFocus True Day/Night Indoor Vandal Color Camera ED550. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei EverFocus True Day/Night Indoor Vandal Color Camera ED550 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
