Benutzeranleitung / Produktwartung RX8200 des Produzenten Ericsson
Zur Seite of 44
RX8200 Advanced Modular Receive r Software Version 4.3.2 USER GUIDE EN/LZT 790 0009 R1A.
RX8200 Advanced Modular Receiver Copyright © Copyright Ericsson AB 2011. All rights reserved. Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner.
Contents Contents 1 Introduction ............................................................................................ 5 1.1 Who Should Use this User Guide? .......................................................... 5 1.2 What Equipment is Covered by this User Guide? .
Contents EN/LZT 790 0009 R1A 2011-03-3 0 4 (44) List of Figures Figure 1 Rear Panel Connectors ..........................................................................10 Figure 2 Front Panel LEDs and Pushbuttons .....................................
Introduction 1 Introduction 1.1 Who Should Use this User Guide? This User Guide is written for operators/users of the RX8200 Advanced Modular Receiver to assist in installation and operation. Detailed infor mation can be found in the Reference Guide companion document which is issued on CD.
Introduction T able 2 RX8200 Hardware Options Marketing Code Price Object Number Supply Object Number Description RX8200/HWO/DVBS2 FAZ 101 0113/5 ROA 128 3757 DVB-S2 Input Card RX8200/HWO/IP/GIGE FAZ 101 0113/12 ROA 128 3761 Gigabyte 100/1000BaseT Ethernet RX8200/HWO/G703 FAZ 101 0113/8 ROA 128 3763 G.
Introduction Marketing Code Price Object Number Supply Object Number Description RX8200/SWO/MP2/MP4/ SD/HD FAZ 101 0113/41 FAT 102 0156 MPEG-2 & MPEG-4 HD and SD Decode RX8200/SWO/SING/SERVFILT FA.
Introduction Marketing Code Price Object Number Supply Object Number Description 1080i or 720p) RX8200/SWO/XCONV FAZ 101 0113/55 FAT 102 0175 Cross-co nversion RX8200/SWO/FSYNC FAZ 101 0113/33 FAT 102.
Installing the Equipment 2 Inst alling the Equipment 2.1 Introduction For best performance and reliability follow the instructions for site requirements and installation in the Reference Guide and only use installation accessories recommended by the manufacturers.
Installing the Equipment Warning! The Technical Earth is not a Protective earth for electric shock protection. This unit must be correctly earthed through the molded plug supplied. If the local mains supply does not have an earth conductor do not connect the unit.
Installing the Equipment ) Type of Connector Description ASI/SD-SDI/HD-SDI OUT 1 , 2 & 3 75 Ω BNC connector for ASI or SDI (user selectable) output feeds. ASI INPUT 75 Ω BNC connector for A SI input feed. CONTROL 1 & 2 8-way RJ-45 connectors for 10/100BaseT Ethernet control and monitoring.
Quick Start Guide: Connect- P ower - Configure 3 Quick S tart Guide: Connect-Power-Configure 3.1 Connecting the Receiver The following points should be noted when making signal connections to the receiver: • For models with option RX8200/HWO/DVBS2 fitted, connect the incoming satellite RF feed to the rear panel connector marked RF IN 1 - 4 .
Quick Start Guide: Connect- P ower - Configure 2. Switch on the AC power supply to the unit at the wall or rack outlet. Note: The RX8200 Receiver does NOT contain a power on/off switch. 3. After a short period of initialization the following screen is displayed on the Front Panel: INITIALIZING 4.
Quick Start Guide: Connect- P ower - Configure 8. Set the set the LNB power output level A description of each of these User Settings can be found in the Reference Guide . Note: If the unit has successfully locked to the incoming feed, then the TS Lock value in menu Input should be LOCKED .
Quick Start Guide: Connect- P ower - Configure 9. Set up Sync Count to Lock/Sync Miss Sample Size 10. Set up Sync Miss Limit. A description of each of these User Settings can be found in the Reference Guide . Note: If the unit has successfully locked to the incoming feed, then the TS Lock value in menu Input should be LOCKED .
Quick Start Guide: Connect- P ower - Configure • The unit will automatically decode the first two audio components that it finds within the selected service. • Alternative audio components may be selected from the service tab on the Web Control interface.
Front P a nel C ontrol 4 Front Panel Control 4.1 Introduction The Front Panel display and keypad may be used to configure, control and monitor the receiver when an external control system is not used.
Front P a nel C ontrol 4.3.2 LCD A 2-line x 40-character back-lit dot-matrix Liquid Crystal Display (LCD) displays various menus and settings. The menus and setting available will vary depending on which options have been enabled through the purchase of a suitable lice nse.
Front P a nel C ontrol 4.4 Front Panel Menus An overview of the available Front Panel menus is shown below. The menus and settings available will vary depending on which receiver model is being used and which options have been enabled through the purchase of a suitable lice nse.
Front P a nel C ontrol — 2.2.1 Status 2.2.1.1 Lock Statu s 2.2.1.2 Error Rati o/ Signal Level 2.2.1.3 Modulation/ F E C Rate 2.2.1.4 Standard/Spectral Sense 2.2.1.5 Pilot Symbol s/Fram e Size — 2.2.2 Source 1 Conf i gure 2.2.2.1 LNB Lo Freque nc y 2.
Front P a nel C ontrol 4.4.1 Menu Structure The Front Panel menus and sub-menus, av ailable on the LCD, provide the configuration parameters that may be viewed, selected and/or modified. • System - Provides sub-menus for viewing/config uring the receiver hardware and access parameters.
Front P a nel C ontrol - Director – Enables configuration of Director Conditional Access parameters, such as: ID numbers, download status and the facility to reset or change the PIN number. • Output Menu - Provides sub-menus for viewing/configuring the receiver output parameters.
Web Br o w ser Control 5 W eb Browser Control 5.1 Introduction A personal computer (PC) running a Web Browser can be used to configure, control and monitor the receiver remotely.
Web Br o w ser Control Unit Model Number and Name About button Header Function Tabs Navi g ation Path Toolbar Main Web Page Results Frame Figure 5 Web Page Overview (T ypical) • Header – The header of the web page displays the Ericsson logo and the unit model number name.
Web Br o w ser Control web page. When you switch between tabs, the browser remembers the path for each tab. • Navigation Path – The web pages are organized into a tree-like structur e, like the directory on a computer.
Web Br o w ser Control 5.3 W eb Pages 5.3.1 Status This web page shows a number of top-level parameters indicating the current status of the receiver. Figure 7 S tatus Web Page 5.
Web Br o w ser Control Figure 8 Device Info Web Page This page also provides buttons to the following further web pages: • Build – provides details of equipment build and version numbers. No user- editable fields. • Environment – provides details of the phy sical environment of the equipment such as temperature and fan speed.
Web Br o w ser Control 5.3.3 Alarms The Alarms web page provides access to the alarms settings for the receiver. The contents of this page are composed mainly of fields with drop-down menus which allow the setting or masking of various alarms and check boxes which can be used to activate relay mapping.
Web Br o w ser Control Figure 9 Alarms W eb Page 5.3.4 Customization Web Page The Customization web page provides acce ss to the list of licenses enabled on the equipment and to enable further licenses (as purchased) by entering the custom key provided.
Web Br o w ser Control • RAS - allows the user to select Digital Satellite News Gathering (DSNG) or Fixed Key mode and input a 7-digit DSNG key. Figure 1 1 CA Web Page 5.3.6 Input The Input Web Page provides access to the parameters of the various inputs to the receiver.
Web Br o w ser Control Figure 12 Input Web Page (Satellite Input Card fitted) Click on the Satellite Input button on the Input page to display a further sub page.
Web Br o w ser Control If the I/P Input Card is fitted, the following web page is displayed. Figure 14 Input Web Page (IP Card fitted) Click on the IP Input button on the Input page to display a fur ther sub page.
Web Br o w ser Control Figure 15 Input > IP Input Sub Page (IP Card fitted) If the G.703 Input Card is fitted, the following web page is displayed. Figure 16 Input Web Page (G .
Web Br o w ser Control Click on the G703 Input button on the Input page to display a further sub page. Figure 17 Input > G .703 Input Sub Page (G .703 Input Card fitted) 5.3.7 Service Plus The Service Plus web page provides access to the various encryption and encoding services available to the receiver.
Web Br o w ser Control • VBI-VANC - gives access to Vertical Blanking Interval-Vertical Ancillary Data Space (VBI-VANC) parameters. • Splice - gives access to the splice operation parameters. • DVB Subtitles - gives access to the Digital Video Broadcasting (DVB) subtitles parameters.
Web Br o w ser Control 5.3.9 Output The Output web page provides access to the output feed parameters of the receiver. Figure 20 Output Web Page 5.3.10 Download The Download web page provides access to the over air download status of the receiver. There are no user-editable fields on this page.
Web Br o w ser Control Figure 21 Download Web Page 5.3.11 SNMP This page gives access to the Simple Network Management Protocol (SNMP) parameters for the receiver, including protocol selection and MIB parameters. Figure 22 SNMP Web Page 5.3.12 Presets The Presets web page gives access to a list of 40 preset configurations.
Web Br o w ser Control Figure 23 Presets W eb Page 5.3.13 Save/Load The Save/Load web page provides a range of configuration download and upload facilities, including saving and restoring unit confi guration, saving unit MIB files, saving alarm log files and saving splice log files.
Web Br o w ser Control Figure 24 Save/Load Web Page 5.3.14 Help The Help web page gives access to a Web Interface User Guide which provides a brief description of the interface functionality.
Equipment P a ckaging 6 Equipment Packaging 6.1 Packaging S tatement The outer carton and any cardboard inserts are made from 82% recycled material and are fully recyclable. The Stratocell ® or Ethafoam 220 ® polyethylene foam inserts can be easily recycled with other low density polyethylene (LDPE) materials 6.
Materials Declarations 7 Materials Declarations 7.1 Overview Ericsson products are designed and manufactured in keeping with good environmental practice. Our component and materials selection policy prohibits the use of a range of potentially hazardous materials.
Disposal of this Equipment 8 Disposal of this Equipment 8.1 General Dispose of this equipment safely at the end of its life. Local codes and/or environmental restrictions may affect its disposal. Regulations, policies an d/or environmental restrictions differ throughout the world.
Re c y cling 9 Recycling Ericsson SA TV Recycling has a process facility that enables customers t o return Old and End-of-Life Products for recycling if it is required. Ericsson provides assistance to customers and recyclers thr ough our Ericsson and SATV Recycling eBusiness Portal.
Re c y cling EN/LZT 790 0009 R1A 2011-03-3 0 44 (44).
Ein wichtiger Punkt beim Kauf des Geräts Ericsson RX8200 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ericsson RX8200 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ericsson RX8200 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ericsson RX8200 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ericsson RX8200 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ericsson RX8200 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ericsson RX8200 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ericsson RX8200. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ericsson RX8200 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
