Benutzeranleitung / Produktwartung RX8000 des Produzenten Ericsson
Zur Seite of 236
RX8000 Series Receivers Software Version 4.3.2 REFERENCE GUIDE EN/LZT 790 0005 R1A.
RX8000 Series Receivers ENGLISH (UK) - READ THIS FIR ST! If you do not under stand the co ntents of this man ual. DO NOT OPERATE THIS EQUIPMENT . Also , translation into any EC official language of thi s manual can be made av ailable, at your cost. ITALIANO - LEGGERE QUESTO AVVISO PER PRIMO! Se non si capisce il contenuto del pre sente manuale.
Contents EN/LZT 790 0005 R1A 2011-03- 30 iii Contents Chapter 1: Introduction This chapter identifies the equipment versions covered by this manual, describes the purpose of the equipment and provides a summary of features, controls and indicators.
Preliminary Pages Introduction This Reference Guide provides instructions and information for the installation and operation of the RX8000 Receiver range. This Reference Guide should be kept in a safe place for reference for t he life of the equipment.
Preliminary Pages Registered trademarks and trademarks used are acknowledged below and marked with their respective symbols. However, t hey are not marked within the text of this Reference Guide. Registered Trademarks Ethernet ® Registered trademark of Xerox Corporation.
Preliminary Pages Warning! Warnings give information which, if strict ly observed, will prevent personal injury or death, or damage to property or the environment. They are highlighted for emphasis, as in this example, and are placed immediately preceding the point at which the reader requires them.
Preliminary Pages For systems support you can choose either Gold Business Critical support or Silver Business Advantage . These packages are designed to save you costs and protect your income through enlisting the help of Ericsson support specialists.
Preliminary Pages EN/LZT 790 0005 R1A 2011-03- 30 viii Return of Equipment If you need to return equipment for repair please contact your local Ericsson Customer Services Department. Please refer to the Customer Services contact information on page vii.
1 Introduction Chapter 1 Contents 1.1 Introduction ........................................................................................... 1-3 1.1.1 Who Should Use this Reference Guide ................................................ 1-3 1.1.2 What Equipment is Covered by this Reference Guide .
Chapter 1 EN/LZT 790 0005 R1A 1-2 List of Figures Figure 1.1 Typical Satellite Compression System ............................................... 1-17 Figure 1.2 What the Satellite Receiver Does....................................................... 1-18 Figure 1.
Chapter 1 1.1 Introduction 1.1.1 Who Should Use this Reference Guide This Reference Guide is written for operators / users of the RX8000 Series Receivers. It describes the units’ functions and operation. The Reference Guide is written to assist in the installation and day-to-day care and op eration of the unit.
Chapter 1 This Reference Guide covers the functions of software version 4.3.2 and later . To verify the installed version either: • Access the front panel System Menu (Menu 1.2.1). The front panel menus are described in Chapter 3, Front Panel Control.
Chapter 1 T able 1.3 RX8200 Software Options Marketing Code Price Object Number Supply Object Number Description RX8200/SWO/DVBS2/QPSK FAZ 101 0113/32 FAT 102 0151 DVB-S2 QPSK License key RX8200/SWO/D.
Chapter 1 Marketing Code Price Object Number Supply Object Number Description RX8200/SWO/HDSDI/3G FAZ 101 0113/34 FAT 102 0176 MPEG-4 HD 4:2:2 1080p 50/60 Decoding RX8200/SWO/MP2/422/SD FAZ 101 0113/5.
Chapter 1 Marketing Code Price Object Number Supply Object Number Description RX83XX/SWO/PW FAZ 101 0108/29 FAT 102 0110 Passwo rd Protection for Web Browser RX83XX/SWO/AAC FAZ 101 0108/2 FAT 102 0370.
Chapter 1 Marketing Code Price Object Number Supply Object Number Description RX83XX/SWO/SING/SERVFILT FAZ 101 0108/15 FAT 102 0138 Single Service Filtering RX83XX/SWO/MULT/SERVFILT FAZ 101 0108/14 FA.
Chapter 1 Marketing Code Price Object Number Supply Object Number Description RX83XX/SWO/NULL FAZ 101 0108/17 FAT 102 0114 Null Packet TS License RX8320/SWO/IP/OUT FAZ 101 0108/25 FAT 102 0134 IP Transport Stream Out License Key RX8320/UPG/IP/OUT FAZ 101 0108/26 FAT 102 0135 IP Transport Stream Output T able 1.
Chapter 1 Marketing Code Price Object Number Supply Object Number Description RX83XX/SWO/MP2/MP4/SD FAZ 101 0108/12 FAT 102 0111 MPEG-2/4 SD 4:2:0 Decoding RX83XX/SWO/MP2/MP4/ SD/HD FAZ 101 0108/11 FA.
Chapter 1 • Status LED indicates input feed lock and general alarm conditions. • Alarm handling via single configurable alarm relay and a date and time stamped alarm log. • 1 x ASI input with 75 Ω connector. • 2 x ASI Transport Stream outputs with 75 Ω connectors.
Chapter 1 • Dolby Digital ® decoding / downmixing. • Director 5 control and de-scrambling. 1.2.2 RX8310 Distribut ion Receiver The RX8310 combines a DVB-S2 demodulator with Ericsson’s Director secure content delivery and over-air receiver control solution as a standard feature.
Chapter 1 • MPE IP data de-encapsulation. • Single service filtering and PID remapping. • Multi-service filtering and stream splitting. 1.2.3 RX8315 Distribut ion Receiver The RX8315 enables video distribution for both analog and digital networks.
Chapter 1 • MPEG-4 AVC HD down-conversion through CVBS output. • 2 x stereo pair Dolby® Digital audio decoding with 5.1 to 2.0 down-mixing. • AAC audio decoding with 5.1 to 2.0 down-mixing. • MPE IP data de-encapsulation. • Single service filtering and PID remapping.
Chapter 1 • 2 x stereo pairs balanced analog audio output. • Front panel and web browser control, with alarm relay. 1.2.4.2 RX8320 Factory Fit Optional Hardware Features • Dual Gigabit IP data / feed output on dual redundant RJ-45 output connectors.
Chapter 1 • Front panel and Web browser control, with alarm relay. • SCTE 35 controlled contact closures for ad-insertion signaling. 1.2.5.2 RX8330 Factory Fit Optional Hardware Features • Dual Gigabit IP data / feed output on dual redundant RJ-45 output connectors.
Chapter 1 1.3 The Satellite Receiver 1.3.1 Typical Satellite System The RX8000 Series Receiver is a component of the MPEG-4 AVC/ MPEG-2/DVB compliant range of Ericsson equipment. They are designed for use by broadcasters and distributors of video, audio and data Services over satellite.
Chapter 1 1.3.3 What the Satellite Receiver Does The Receiver can be tuned to a specified satellite channel fr equency and polarization. The input is down-converted via a Low-Noise Block (LNB) to provide an L-band input to the Receiver. The front-end tuning is microprocessor controlled with a frequency synthesized local oscillator.
Chapter 1 1.4 The T elco Receiver/Decoder 1.4.1 Typical Decoder System The Decoder is a component of Ericsson range of equipment. It is designed for use by broadcasters and distributors of video and audio Services. It can be used as a Transport Stream monitor or to decode si gnals received over a telecommunications network.
Chapter 1 The Decoder is configured to select a single video Service and other audio/data components from the multiple Services on the incoming Transport Stream and present them at the output. Figure 1.4 Role of the Decoder Note: G.703 input may also be used to interface to telco infrastructure.
Chapter 1 EDIT SAV E DOW N RI GHT LE FT U P LCD USB Co nn ecto r ( Se rv ic i ng Onl y ) S tat us LE D CA SLO T Figure 1.5 Front Panel Controls (RX8200) Table 1.12 Front Panel Controls Item Color Description CA Slot - Conditional Access Slot. Located on front panel of RX8200 and rear panel of RX831 0, RX8315 and RX8330.
Chapter 1 1.7 Rear Panels All inputs, outputs and control connections are taken via the rear panel. Due to the modular nature of these units, factory fitted hardware modules with different connections can be fitted to any unit and therefore only a typical (sample) rear panel images are shown below.
Chapter 1 Table 1.13 Rear Panels Item Type Description RF IN 1-4 F-type 75 Ω Radio Freque ncy (L-band) input. ASI OUT 1-2 ASI/SDI OUT ASI/HD-SDI/SD-SDI OUT BNC 75 Ω ASI = Asynchronous Serial Interface. SDI = Synchronous Data Interface. SD-SDI = Standard Definition SDI.
Chapter 1 EN/LZT 790 0005 R1A 1-24 BLANK.
2 Inst alling the Equipment Chapter 2 Contents 2.1 Read This First! .................................................................................... 2-3 2.1.1 Handling ...............................................................................
Chapter 2 EN/LZT 790 0005 R1A 2-2 2.7.9 ASI IN Connector ............................................................................... 2-14 2.7.10 COMPONENT VIDEO Connector (RX8200 only) .............................. 2-14 2.7.11 DATA OUT Connector.
Chapter 2 2.1 Read This First! 2.1.1 Handling The equipment must be handled and installed carefully and thoughtfully to prevent safety hazards and damage. 2.1.2 Installing the Equipment Ensure the personnel designated to fit the unit have the appropriate skills and knowledge.
Chapter 2 Where appropriate, ensure this product has an adequate level of lightning protection. Alternatively, during a lightning storm or when it is left unattended and unused for long periods of time, unplug it from the supply outlet and disconnect the output equipment.
Chapter 2 2.3.2 Ventilation 2.3.2.1 Openings in the Covers Si de openings in the unit, as well as side-mount ed cooling fans, are pr ovided for ventilation. The y ensure reliable opera tion of the product and protect it fro m overheatin g. The openings of th e fans must no t be blocked or co vered.
Chapter 2 2.3.3 Installing Cables - Safety Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cables at plugs, convenience receptacles, and the point where they exit from the appliance.
Chapter 2 Warnings! The RX8000 series receivers should only be oper ated from the type of power source indicated on the marking label. If you are not sure of the type to your business, consult your appliance dealer or local pow er company. Do not overload wall outlets and extension cords as this can result in a risk of fire or electric sho ck.
Chapter 2 T able 2.1 Supply Cord Wiring Colors UK (BS 1363) EUROPE (CEE 7/7) USA (NEMA 5-15P) Earth: Green-and-yellow Green-and-yellow Green Neutral: Blue Blue White Live: Brown Brown Black If the colors do not correspond with the colored markings identifying the terminals in a locally supplied plug, proceed as in Annex B.
Chapter 2 2. Eliminate the migration of stray charges when connecting between equipment. To do this, connect a wire between the Technical Earth terminal and a suitable point on the rack. The Technical Earth provides a suitable connection between the equipment and the installation to give a low impedance path at normal operating frequencies.
Chapter 2 All signal connections are made via the rear panel. A typical rear panel is shown in Figure 2.5 . Full technical specifications for the connections are given in Annex B .
Chapter 2 Cautions! The receiver provides DC power (see Chapter 3, Front Panel Control for details of menu option) via the active L-band input connector to drive an LNB. Do not connect equipment other than an LNB to this connector. Failure to do this may result in damage to the external equipment.
Chapter 2 2.7.4 ASI/SDI OUT Connector (RX8200 and RX8330 only) The unit provides two coaxial ASI/SDI outputs depending on the user selectable configuration.
Chapter 2 2.7.7 AUDIO/AUDIO OUT Connector All units provide a pair of connectors supplying two stereo channels. Each carries a single channel stereo pair in both analogue and balanced digital form.
Chapter 2 2.7.9 ASI IN Connector All units provide an ASI input socket for detection of the transport stream lock on the ASI input. Table 2.10 ASI IN Conn ector Item Specification Connector type BN C 75 Ω female s ocket Connector designation AS I IN Pin-outs Centre Shield Input Ground/Chassis ASI IN 2.
Chapter 2 2.7.11 DATA OUT Connector A data output interface may be used with either RS232 or RS422 connector, as described below. Table 2.12 DATA OUT Connector Item Specification Connector type 9- wa .
Chapter 2 EN/LZT 790 0005 R1A 2-16 2.7.13 RS232/RS485 REMOTE Connector A remote control interface may be used with either RS232 or RS485 connector, as detailed below.
3 Front Panel Control Chapter 3 Contents 3.1 Introduction ........................................................................................... 3-3 3.2 Powering the Equipment ......................................................................
Chapter 3 EN/LZT 790 0005 R1A 3-2 3.5.7.1 4.1 Service Table ............................................................................... 3-52 3.5.7.2 4.2 Director .....................................................................................
Chapter 3 3.1 Introduction This chapter describes the features and opt ions provided by the Front Panel menus for controlling the RX8000 Series Receivers locally. 3.2 Powering the Equipment 3.2.1 Switching On Caution! This equipment should not be operated unless the cooling fans are working and there is free-air flow around the unit.
Chapter 3 Figure 3.1 Power Up Operating Mode 3.3 Using the Front Panel Controls The user interface for the Front Panel consists of an alphanumeric Liquid Crystal Display, pushbuttons, and a status LED that are used to set-up, control and monitor the unit.
Chapter 3 EDIT SAV E DOW N RI GHT LE FT U P LCD USB Co nn ecto r ( Se rv ic i ng Onl y ) S tat us LE D CA SLO T Figure 3.2 Front Panel Controls (RX8200) 3.3.1 USB Connector This connector is for factory / service use only. 3.3.2 Status LED This multi-coloured LED provides a visual indication of the summary status of the unit.
Chapter 3 3. Service : This menu includes user settings for the currently selected service for decode from the incoming feed. 4. CA Systems : This menu includes user settings for: the currently selecte d services for decryption from the incoming feed, Director parameters and status.
Chapter 3 2. To ignore any changes that have been made and to return to the original setting, press the Edit pushbutton. 3.4 Example Configuration The following example configuration uses the Front Panel menus to set up the DVB-S2 Satellite Receiver (not available for RX8320) using Menu 2.
Chapter 3 3.5 Front Panel Menus An overview of the available Front Panel menus is shown in Figure 3.3 . The menus and settings available will vary depending on which receiver model is being used and which options have been enabled through the purchase of a suitable license.
Chapter 3 — 2.2.1 St atus 2.2.1.1 Lock Statu s 2.2.1.2 Error Rati o/ S ignal Level 2.2.1.3 Modulation/ F E C Rate 2.2.1.4 Standard/Spectral Sense 2.2.1.5 Pilot Symbol s /Frame Size — 2.2.2 Sour ce 1 Conf igur e 2.2.2.1 LNB Lo Freque ncy 2.2. 2.2 Satell ite Fr equency 2.
Chapter 3 3.5.1 1 System Shortly after switch-on, the Status LED will turn green and arrow keys will be lit depending on which further menus are available.
Chapter 3 4. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. 3.5.1.1.2 1.1.2 MAC1 To access the MAC1 menu, press the T (Down) key. The following screen is displayed: MAC1 |MAC#1 1.1.2 |00:20 :AA:55:05:9C To edit the MAC1 address: 1.
Chapter 3 To edit the Gateway address: 1. Press the Edit key. The cursor appears below the first character of the Gateway address. 2. Edit the address as required using the W (Back) and X (Forward) key s to select each digit in turn, and then using the S (Up) and T (Down) keys to increment or decrement the digit.
Chapter 3 3.5.1.2.3 1.2.3 SD FPGA Ve rsion To view the Standard Definition (SD) Field Programmable Gate Array (FPGA) version, press the T (Down) key. The following screen (or a similar screen) is displayed: VERSIONS |SD FP GA VERSION 1.2.3 |0.2.5 [Bui lt: Thu Apr 8 16:25:22 2010] The bottom line scrolls to display the version details.
Chapter 3 3.5.1.2.8 1.2.8 422 FW (Option Card) To view the 4:2:2 Firmware (FW) version (dependent on model and option licences obtained), press the T (Down) key.
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. 4. If YES is saved, inputs will be reset and the unit rebooted immediately. 3.5.1.4.2 1.4.2 Reset All Incl IP & Reboot To access this function, press the T (Down) key.
Chapter 3 2. Use the S (Up) and T (Down) keys to toggle between OFF and ON. 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 3.5.2.2 2.2 Select Satellite Input This menu allows the choice of up to four RF Inputs. To access this menu, press the T (Down) key. The following screen is displayed: S2 |SELECT SAT ELLITE INPUT 2.2 |RF Input 01 > To select the relevant RF Input: 1.
Chapter 3 3.5.2.2.1.4 2.2.1.4 Standard/Spectral Sense To view the status of these parameters, press the T (Down) key. The following screen is displayed: STATUS |STANDARD --- 2.2.1.4 |SPECTRAL SENSE --- 3.5.2.2.1.5 2.2.1.5 Pilot Sy mbols/Frame Size To view the status of these parameters, press the T (Down) key.
Chapter 3 SOURCE 1 |SATELLI TE FREQUENCY 2.2.2.2 |01550.000 MHz (UNLOCKED) To edit the frequency setting: 1. Press the Edit key. The cursor appears below the first number.
Chapter 3 3.5.2.2.2.5 2.2.2.5 Rolloff To view and edit the current Source 1 Rolloff settings, press the T (Down) key. The following screen is displayed and the Edit key is lit: SOURCE 1 |ROLLOFF 2.2.2.5 |20% (UNLOCKED) To edit the Rolloff setting: 1. Press the Edit key.
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. 3.5.2.2.2.8 2.2.2.8 LNB Power OP To view and edit the current Source 1 LNB power output settings, press the T (Down) key. The following screen is displayed and the Edit key is lit: SOURCE 1 |LNB POWER OP 2.
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. This is the end of the Source 1 configure menu options. To return to the Source 1 menu press the W (Back) key. 3.5.2.2.3 2.2.3 – 2.2.
Chapter 3 3. Use the S (Up) and T (Down) keys to toggle between the available types: ASI and IP Input (dependent on model and option licences obtained). 4. Press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 STATUS |IP PACK ETS RECEIVED 2.2.1.4 |0000000000 3.5.3.2.1.5 2.2.1.5 Corrected Packet Count To view the corrected packet count, press the T (Down) key. The following screen is displayed: STATUS |CORRECTED PACKET COUNT 2.2.1.5 |0000000000 3.5.
Chapter 3 STATUS |FIFO OVERF LOW COUNT 2.2.1.10 |0000000010 3.5.3.2.1.11 2.2.1.11 MDI Delay Factor To view the MDI Delay Factor, press the T (Down) key. The following screen is displayed: STATUS |MDI DE LAY FACTOR 2.2.1.11 |00.000 3.5.3.2.1.12 2.2.1.12 MDI Media Loss Rate To view the MDI media loss rate, press the T (Down) key.
Chapter 3 NETWORK 1 |IP ADDRESS 1 2.2.2 |000.000 .000.000 < To edit the Network 1 IP address: 1. Press the Edit key. The cursor appears below the first character of the address.
Chapter 3 3.5.3.2.2.3 2.2.2.3 MAC Address 1 To view the MAC Address 1, press the T (Down) key. The following screen is displayed: NETWORK 1 |MAC ADDRESS 1 2.2.2.3 |00:20 :AA:4f:06:1b 3.5.3.2.2.4 2.2.2.4 Ethernet Line Mode 1 To view and edit the Ethernet Line Mode 1, press the T (Down) key.
Chapter 3 3.5.3.2.2.8 2.2.2.8 ICMP Enable 1 To view and edit the ICMP 1, press the T (Down) key. The following screen is displayed: NETWORK 1 |ICMP ENABLE 1 2.2.2.8 |Enable To enable/disable the ICMP: 1. Press the Edit key. The cursor appears below the first character of the displayed option.
Chapter 3 2. Edit the parameter value as required using the W (Back) and X (Forward) keys to select each digit in turn, and then using the S (Up) and T (Down) keys to increment or decrement the digit. 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 This is the last of the Network 1 screens. To ret urn to the top level Network 1 screen press the W (Back) Key. 3.5.3.2.3 2.2.3 Network 2 From the Network 1 screen 2.2.2, press the T (Down) key. The following screen is displayed. NETWORK 2 |IP ADDRESS 2 2.
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. 3.5.3.2.4.2 2.2.4.2 SNMP Enable To view and edit the SNMP, press the T (Down) key. The following screen is displayed: SETUP |SNMP ENABLE 2.
Chapter 3 2. Edit the parameter value as required using the W (Back) and X (Forward) keys to select each digit in turn, and then using the S (Up) and T (Down) keys to increment or decrement the digit. 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 2.2.4.7 |0 .004 To edit the MDI Media Loss Rate: 1. Press the Edit key. The cursor appears below the first character of the displayed option. 2. Edit the parameter value as required using the W (Back) and X (Forward) keys to select each digit in turn, and then using the S (Up) and T (Down) keys to increment or decrement the digit.
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. This is the last of the I/P Port screens. To return to the top level I/P Port screen, press the W (Back) key. 3.5.3.2.6 2.2.6 Stream 1/ Unicast Enable 1 To view and edit the Unicast Enable 1, press the T (Down) key.
Chapter 3 To edit the Source IP Address 1: 1. Press the Edit key. The cursor appears below the first character of the displayed value. 2. Edit the parameter value as required using the W (Back) and X (Forward) keys to select each digit in turn, and then using the S (Up) and T (Down) keys to increment or decrement the digit.
Chapter 3 3.5.3.2.6.5 2.2.6.5 Row Port 1 To view and edit the Row Port 1, press the T (Down) key. The following screen is displayed: STREAM 1 |ROW PORT 1 2.2.6.4 |00000 To edit the Row Port 1 value: 1. Press the Edit key. The cursor appears below the first character of the displayed value.
Chapter 3 3.5.3.2.8.2 2.2.8.2 Port 1/ 2 Link Down To view the alarms for ports 1 and 2, press the T (Down) key. The following screen is displayed: ALARMS |PORT 1 LIN K DOWN Alarm 2.2.8.2 |PORT 2 LINK DOWN Alarm 3.5.3.2.8.3 2.2.8.3 Port 1/ 2 IP Conflict To view the IP alarms for ports 1 and 2, press the T (Down) key.
Chapter 3 This is the last of the Alarm screens. To return to the top level Alarm screen, press the W (Back) key. 3.5.3.2.9 2.2.9 Version To view the Unit Software Version, press the T (Down) key. The following screen is displayed: VERSION |SOFTWAR E VERSION 2.
Chapter 3 To choose the Select input type: 1. Press the Edit key. The cursor appears below the displayed type (ASI shown above). 2. Use the S (Up) and T (Down) keys to toggle between the available types: ASI, 8VSB and AUTO (dependent on model type). 3.
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. To enable/disable the Auto Tune function: 1. Press the Edit key. The cursor appears below the current option. 2. Use the S (Up) and T (Down) keys to toggle between the Enabled/Disabled options until the required option is displayed.
Chapter 3 2. Press the Edit key. The cursor appears below the displayed type (ASI shown above). 3. Use the S (Up) and T (Down) keys to toggle between the available types: ASI and G.703 (dependent on model and option licences obtained). 4. Press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 3.5.5.2.1.4 2.2.1.4 ATM Alert Status To view the ATM Alert Status, press the T (Down) key. The following screen is displayed: STATUS |ATM AL ERT STATUS 2.2.1.4 | SYNC LOSS 3.5.5.2.1.5 2.2.1.5 PDH Rate/Framing To view the PDH Rate/Framing Status, press the T (Down) key.
Chapter 3 SETUP |MODE MPEG 2.2.2.1 | To choose the Mode: 1. Press the Edit key. The cursor appears below the displayed type (MPEG shown above). 2. Use the S (Up) and T (Down) keys to toggle between the available types: MPEG and ATM (dependent on model and option licences obtained).
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. 4. Use the X (Forward) and W (Back) keys to toggle between the Reed-Solomon and Derandomizer inputs.
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. 4. Use the X (Forward) and W (Back) keys to toggle between the ATM Delta and ATM Alpha inputs. To select the ATM Alpha value: 1. Press the Edit key.
Chapter 3 SETUP |ATM HEADER ERR IGNORE FALSE 2.2.2.7 |ATM VPI 017 To select the ATM Header Err Ignore value: 1. Press the Edit key. The cursor appears below the displayed type (FALSE shown above). 2. Use the S (Up) and T (Down) keys to toggle between the available options: TRUE and FALSE (dependent on model and option licences obtained).
Chapter 3 3.5.5.2.2.9 2.2.2.8 Sy nc Miss Limit To access the Sync Miss Limit Setup function, press the T (Down) key. The following screen is displayed: SETUP |SYNC MISS LIM IT 003 2.2.2.9 | To set the Sync Miss Limit value: 1. Press the Edit key. 2. Use the S (Up) and T (Down) keys until the required value is obtained.
Chapter 3 STATUS |SERVICE ID: 00002 3.1.1 |SERVICE NO PMT The second line of the display shows information about the decryption status of the service. To return to the previous menu, press the W (Back) key. 3.5.6.2 3.2 Video To access the Video menu, press the T (Down) key.
Chapter 3 6. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. To edit the user STD: 1. Press the Edit key. The cursor appears below the first character of the current STD selection. 2. Use the S (Up) and T (Down) keys to toggle between the MPEG-4 AVC and MPEG-2 options.
Chapter 3 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting. This is the last of the Video service options, to return to the Video service menu, press the W (Back) key. 3.5.6.3 3.3 Audio To access the Audio Service menu, press the T (Down) key.
Chapter 3 2. Edit the parameter value as required using the W (Back) and X (Forward) keys to select each digit in turn, and then using the S (Up) and T (Down) keys to increment or decrement the digit. 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 options Decoder 1, STEREO to Decoder 6, STEREO are available. If disabled, available options are Decoder 1, STEREO and Decoder 2, STEREO. 3. Select the required option and press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 To return to the Service Table Menu and access further menus, press the W (Back) key twice. 3.5.7.1.1.2 4.1.1.2 - 4.1.1.24 Service ID Slots 2-24 If the unit is a multi-service descrambler (depending on the model and licenses enabled) there can be up to 24 menus similar to that shown in Para 3.
Chapter 3 DIR |UNIQUE HAR DWARE ID 4.2.3 |34390968634 3.5.7.2.4 4.2.4 Manuf ID To view the manufacturer, model and hardware identifier values, press the T (Down) key. The following screen is displayed: DIR |MANUF ID DE HW TYPE 82 4.2.4 |MODEL ID 1D 3.
Chapter 3 When the reset PIN is input, the local lockout PIN will be reset. To reset PIN: 1. Press the Edit key. The cursor appears below the first character of the current selection. 2. Use the Up, T (Down), X (Forward) and W (Back) keys to enter the required number.
Chapter 3 DIR |POWER-U P CARRIER 4.2.10 |NO ST ORED SERVICE The second line displays the service name of the stored service. 3.5.7.2.11 4.2.11 Emergency Home Carrier To view the current condition of this option, press the T (Down) key. The following screen is displayed: DIR |EMERGENCY HOME CARRIER 4.
Chapter 3 Note: Selecting AUTO will output SD-SDI for SD material and HD-SDI for HD material. 3. Use the W (Back) and X (Forward) keys to toggle between OUTPUT ONE and TWO. 4. Press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 This is the last of the Output menu options. To return to the Output menu and access further menus, press the W (Back) key . 3.5.9 6 Presets The Preset menu allows the access and editing of 40 sets of equipment pre- configured settings.
Chapter 3 2. Edit the parameter value as required using the W (Back) and X (Forward) keys to select each digit in turn, and then using the S (Up) and T (Down) keys to increment or decrement the digit. 3. Press Save to save the new settings or Edit to abandon the operation and return to the current setting.
Chapter 3 EN/LZT 790 0005 R1A 3-60 BLANK.
4 Remote Control Chapter 4 Contents 4.1 Introduction ........................................................................................... 4-3 4.1.1 Local Control Lockout ..........................................................................
Remote Control EN/LZT 790 0005 R1A 4-2 BLANK.
Remote Control 4.1 Introduction The RX8000 Series Receivers can be remotely controlled / monitored in a variety of ways: • RS232/485 Remote Control Protocol (RCP) • Director Over-Air Control (Not RX8320) • Web Browser • SNMP 4.
Remote Control 4.3 Director Ericsson’s Director Over-Air Control (OAC) system is available either as a standard feature or as an option on all of the RX8000 Series Receivers, except for the RX8320.
Remote Control 4.4 W eb Browser The Web Browser interface is available as a standard feature on all of the RX 8000 Series Receivers. For more detailed information on Web Browser remote control, see Chapter 5, Web Browser Control .
Remote Control Figure 4.1 T ypical Web Browser S tatus Page For more information on the Web Browser interface and a description of the available web pages, see Chapter 5, Web Browser Control . 4.5 SNMP Simple Network Management Protocol (SNMP) is available as a standard feature on all of the RX8000 Series Receivers.
Remote Control 3. Ensure the trap community, read-write community and read-only community are configured as public or private in the same way as the MIB browse or SNMP application being used. 4.5.2 Downloading the MIB SNMP exposes management data in the form of variables on the managed systems, which describe the system configuration.
Remote Control EN/LZT 790 0005 R1A 4-8 BLANK.
5 W eb Browser Control Chapter 5 Contents 5.1 Introduction ........................................................................................... 5-3 5.1.1 Setting up Web Browser Control .......................................................... 5-3 5.
Chapter 5 EN/LZT 790 0005 R1A 5-2 List of Figures Figure 5.1 Web Page Overview............................................................................. 5-3 Figure 5.2 About dialog ...................................................................
Chapter 5 5.1 Introduction This chapter describes the features and options provided by the Web Browser interface menus and web pages for controlling the RX 8000 Series Receivers remotely. The Web Browser interface is available as a standard feature on all of the RX 8000 Series Receivers.
Chapter 5 • Header – The header of the web page displays the Ericsson logo and the unit model number name. At the right-hand side of the header an About button which, when clicked, displays an information dialog about the unit, including the software version number.
Chapter 5 Table 5.1 Web Page Icons, Buttons and Symbols Item Description Navigation Click on this icon to navigate one step up (to the pare nt folder) in the folder structure. Click on this icon to navigate back to the previous view. This i con typically appears when you are editing a single record in a table or a sub-table.
Chapter 5 5.2 W eb Pages 5.2.1 Status To use the receiver Web Browser Interface, the IP address assigned to t he receiver control port in the front panel system menu should be entered into the address field of the Web browser. Provided that the network is correctly configured, the following status page should be automatically loaded and displayed.
Chapter 5 • Audio Status – The decode status of the current audio stream. • CA (Conditional Access) Status - The status of the encryption authorizations. • Output Feed – The status of the output. • Mode – Indicates whether unit configuration is active or redundant.
Chapter 5 • Name – This field contains a name string that can be assigned by the user. The last saved name is displayed on power-up but may be replaced by the user. The default name is the receiver model name. • Product Name – The name and/or model of the product.
Chapter 5 To view this page, select the Environment button from the Device Info Page. Figure 5.6 Device Info > Environment Web Page There are no fields on this page, which may be edited by the user. Selecting the Refresh button will ensure that the latest information is displa yed from the current values of the equipment.
Chapter 5 Figure 5.8 Device Info > Modules Web Page There are no fields on this page which may be edited by the user. Selecting the Refresh button will ensure that the latest information is displa yed from the current values of the equipment. 5.2.2.
Chapter 5 4. Select the Back button to return to the Device Info > Trap Destination Table web page. 5. Select the Apply Changes button to confirm additions. Selecting the Refresh button will ensure that the latest inform ation is being displayed from the current values of the equipment.
Chapter 5 Figure 5.1 1 Alarms W eb Page The contents of this page are composed mainly of fields with drop-down menus which allow the setting or masking of various alarms and check boxes which can be used to activate relay mapping.
Chapter 5 The Parameters section of this web page allows the user to enable fur ther licenses by entering the custom key provided (when a license is purchased) in the Custom Key field. Once the custom key has been entered, the unit will need to be rebooted for the key to become effective.
Chapter 5 5.2.5 CA This page allows viewing of the Conditional Access (CA) Service Status and activation of various Director controls. To view this page, select the CA tab from the top of the current web page.
Chapter 5 Any changes which are made to the CA page functions may be confirmed by selecting the Apply Changes button. Selecting the Refresh button will ensure that the latest information is being displayed from the current values of the equipment. The CA Service Status button allows the user to view the Conditional Access Status Table.
Chapter 5 • Input Source – allows a choice of Source Selection Mode from the drop-down menu. • Primary Input – allows selection of the primary input to the receiver. • Input Loss Switch Period – allows the user to define a period, in seconds, before the unit switches to the alternate input (either Input Source or Primary).
Chapter 5 There are also four Configuration buttons which allow the viewing and setting of the tuning parameters for the four possible RF inputs. Any changes which are made to the Satellite Input page may be confirmed by selecting the Apply Changes button.
Chapter 5 • LNB 22 kHz – this check box allows the LNB 22 kHz signal to be activated. Any changes which are made to the Configuration page may be confirmed by selecting the Apply Changes button. Selecting the Refresh button will ensure that the latest information is being displayed from the current values of the equipment.
Chapter 5 • IP Input TS Null Pkt Threshold – allows the user to determine the IP Input null packet occupancy percentage before switch. This option is available for all inputs (G.703, S2, etc.) An IP Input button is provided on this page which gives access to a further web page.
Chapter 5 Figure 5.20 Input > IP Input Web Page The following user-editable fields are displayed on this web page: User-editable fields in the IP Interface Section: • IP Address 1/2 – allows the user to input the relevant IP address. • Subnet Mask 1/2 – allows the user to input the relevant Subnet Mask address.
Chapter 5 • Mcast IP Address 1/2 – allows the user to set the Multicast IP Address for the primary stream on Port 1/2. • Source IP Address 1/2 – allows the user to set the Source IP Address for the primary stream on Port 1/2. • UDP Port 1/2 – allows the user to set the UDP Port Address for the primary stream on Port 1/2.
Chapter 5 Figure 5.22 Clear ARP Success Window Any changes which are made to the Input>IP Input page may be confirmed by selecting the Apply Changes button. Selecting the Refresh button will ensure that the latest information is being displayed from the current values of the equipment.
Chapter 5 • Primary Input – allows selection of the primary input to the receiver. • Input Loss Switch Period – allows the user to define a period, in seconds, before the unit switches to the alternate input (either Input Source or Primary).
Chapter 5 User-editable fields in the Input Section: • Input source – allows a choice of Source Selection from the drop-down menu. • Primary Input – allows selection of the primary input to the receiver.
Chapter 5 • Derandomizer – checking this box enables the Derandomizer function. User-editable fields in the Advanced Section: • MPEG – allows the selection of the input mode from a drop-down menu. • Sync Cnt to Lock – allows the user to input an a ppropriate value.
Chapter 5 4. If the MSD license is selected, and service filter mode is set to ‘Multiservice’ in the Output tab, the services to be fitted can be added by ticking the filter checkbox. 5. If service filter mode is set to ‘Remap’ in the Output tab, service PIDs may be remapped by selecting ‘remap config’ under PID info.
Chapter 5 Figure 5.27 Decode We b Page The following user-editable fields are displayed on this page . User-editable fields in the Service section: • Service – allows the selection of the decode service is to be used from a drop- down menu • PCR - allows the selection of the PCR to be used from a drop-down menu.
Chapter 5 • Decode Mode – allows the selection of the decode mode from a drop-down menu. User-editable fields in the Decoders 1-6 sections (number of audio decod ers is license and model dependent): • PID – allows the selection of an PID audio for decode from a drop-down menu.
Chapter 5 • Service Hunt – In this mode, upon the loss of a service the unit will sele ct the first available service from the service list. • Service Drop – In this mode, if a service is lost its select ion data will be dropped such that the service will not be selected again upon reacquisition.
Chapter 5 • Test Pattern Standard - allows the selection of the test patt ern standard from a drop-down menu. • Video Output Mode - allows the selection of the video output mode from a drop-down menu. Note: 4:2:2 video cannot be up-scaled or cross-converted on RX 8200.
Chapter 5 Figure 5.29 Decode > VBI-V ANC Web Page EN/LZT 790 0005 R1A 5-31.
Chapter 5 The following user-editable fields are displayed on this page . User-editable fields in the VBI section: • VBI PID - allows selection of the VBI PID from the service list via a drop-down menu. • User PID – allows user to input VBI PID.
Chapter 5 • VANC Station ID User Name - allows input of Station ID user name. User-editable fields from AFD/Bar section: • Enable AFD/Bar - allows enable/disable of AFD/Bar from a drop-down menu. Any changes which are made to the Decode > VBI VANC page may be confirmed by selecting the Apply Changes button.
Chapter 5 Figure 5.31 Decode > DVB-Subtitles Web Page The following fields, which may be edited by the user, are displayed on this page. User-editable fields in the DVB Subtitles section: • PID - allows selection of the type of PID from a drop-down menu.
Chapter 5 Figure 5.32 Decode > T eletext W eb Page The following user-editable fields are displayed on this page . • Teletext PID – allows selection of the type of Teletext PID from a drop-down menu. • Teletext Insertion – allows enable/disable of Teletext Insertion from a drop- down menu.
Chapter 5 Figure 5.33 Output Web Page The following user-editable fields are displayed on this page . User-editable fields in the Output section: • TS (Transport Stream) Feed – allows selection of the type of transport stream output from a drop-down menu.
Chapter 5 • Custom Src IP - allows input of the Custom source IP. User-editable fields in the Common section: • Link Speed – allows the selection of the IP output card lin k configuration. • Spanning Tree – checking this box enables the spanning tree protocol.
Chapter 5 5.2.14 SNMP This page gives access to the Simple Network Management Protocol (SNMP) parameters for the receiver. To view this page, select the SNMP Tab from the current web page.
Chapter 5 5.2.15 Presets This page gives access to a list of 40 preset configurations. This feature may be used to store input (tuning) parameters in order that settings do not have to be re- entered when changes are made. To view this page, select the Presets tab from the top of the current web page.
Chapter 5 5.2.16 Save/Load This page gives access to a range of Configuration download and Upload facilit ies which are supported by the receiver. To view this page, select the Save/Load tab from the top of the current web page.
Chapter 5 Figure 5.37 Save/Load Web Page Only a portion of the web page is shown in Figure 5.37 . The facilities available from this page are as follows: • Save Configuration to File – allows the user to save the current receiver configuration as an XML file.
Chapter 5 EN/LZT 790 0005 R1A 5-42 • Save Splice Logs File - allows the user to save the current splice logs file. It is recommended that these are saved periodically, as they may be required in the event of a fault occurring on the unit.
6 Options Chapter 6 Contents 6.1 Hardware and Software Options .......................................................... 6-3 6.1.1 DVB-S2 Input Card (RX8200/HWO/DVBS2) ........................................ 6-5 6.1.2 8-VSB Input Card (RX83XX/HWO/8VSB) .
Chapter 6 EN/LZT 790 0005 R1A 6-2 6.2.19 Dolby Digital Decode (RX8XXX/SWO/AC3) ....................................... 6-12 6.2.20 AAC Audio Decode (RX8XXX/SWO/AAC) ......................................... 6-12 6.2.21 DVB-S2 16APSK (RX8XXX/SWO/ DVBS2/16APSK) .
Chapter 6 6.1 Hardware and Software Options These options require extra hardware to be fitted to the unit, or, in the case of software, extra licenses to be purchased. See Table 6.1 for a list of availa ble options. Contact the Customer Services Helpdesk for details (see Preliminary Pages ).
Chapter 6 RX8200 RX8310 RX8315 RX8320 RX8330 Option Number Description z z z z RX8XXX/SWO/MP2/MP4/SD MPEG-2 /4 AVC SD 4:2:0 Decoding z z z z RX8XXX/SWO/MP2/MP4/SD/HD MPEG -2/4 AVC HD 4:2:0 Decoding z .
Chapter 6 6.1.1 DVB-S2 Input Card (RX8200/HWO/DVBS2) This option is only available for the RX8200 Receiver and is fitted as standard to the base models of RX8310, 8315 and 8330. With accompanying software options, the DVB-S2 Input card supports DVB-S, QPSK demodulation and DVB-S2, QPSK and 8PSK demodul ation.
Chapter 6 The MPEG-2 4:2:2 SD Decoding Card provides 4:2:2 video decoding facilities. 6.1.6 MPEG-4 AVC 4:2:2 Decoding Card (RX8200/BAS/2) This option is only available for the RX8200 DVB Receiver. RX8200/BAS/2 is equipped with MPEG-4 4:2:2 decoding functionality.
Chapter 6 Figure 6.2 shows a more detailed picture of the MPEG-2 data transfer. TS-packets are mapped in a datagram, using User Data Protocol (UDP), Internet Protocol (IP) and Ethernet. Figure 6.2: Building the Ethernet Frame … Information 14H Information Information 20H 8H 188 188 TS packets (1 to7) UDP datagram IP datagram Ethernet frame 6.
Chapter 6 6.1.12 Balanced Audio Output Ca rd (RX8200/HWO/BAL/AUD) This option is only available for the RX8200 Receiver. The Balanced Audio Output card provides two stereo pairs of balanced analog and digital outputs. If four stereo pairs are required, t wo cards should be ordered.
Chapter 6 The DVB-S2 Low Symbol Rate software option enables a DVB-S2 symbol rate of 1-5 Msym/s. 6.2.4 MPEG-2 SD Decode (RX8XXX/SWO/MPEG2/SD) This option is available for the RX8200, 8310, 8315 and 8330 Receivers. This option enables MPEG-2 SD 4:2:0 decoding.
Chapter 6 6.2.10 Single-Service Filtering (R X8XXX/SWO/SING/SERVFILT) This option is available for the RX8200, 8310, 8315, 8320 an d 8330 Receivers. This option filters a complete service from a Multiple Program Transport Stream (MPTS) source and generates an Single Program Transport Stream (SPTS).
Chapter 6 The output bit rate, which is selected by the user, may be constant (by inserting NULL packets) or variable (plus the increment due to the PSI SI insertion). 6.2.11 Multi-Service Filtering (R X8XXX/SWO/MULTI/SERVFILT) This option is available for the RX8200, 8310, 8315, 8320 an d 8330 Receivers.
Chapter 6 Note: This option is available to all other units by selecting RX8XXX/HWO/IP/OUT. Note this will also order an IP Output Card. 6.2.15 Director (RX8XXX/SWO/DIR5) This option is only available for the RX8200 Receiver. This option provides Director Conditional Access (CA), over-air control and over-air software downloads.
Chapter 6 This option enables two x AAC-LC and HE-AAC decoding. 6.2.21 DVB-S2 16APSK (RX8XXX/SWO/DVBS2/ 16APSK) This option is available for the RX8310, 8315 and 8330 Receivers. This option adds DVB-S2 QPSK, 8PSK and 16APSK capability to the DVB-S2 Input Option Card.
Chapter 6 6.2.27 MPEG-2 SD 4:2:2 Decoding (RX8200/SWO/MP2/SD/422) This option is only available for the RX8200 Receiver. This option enables MPEG-2 SD 4:2:2 Decoding and requires the installation of the MPEG-2 SD 4:2:2 hardware option card.
Chapter 6 This option enables the conversion of HD video from 720p to 1080i or from 1080i to 720p. 6.2.34 Framesync (RX8200/SWO/FSYNC) This option is only available for the RX8200 Receiver.
Chapter 6 EN/LZT 790 0005 R1A 6-16 BLANK.
7 Preventive Maintenance and Fault-Finding Chapter 7 Contents 7.1 Introduction ........................................................................................... 7-3 7.2 Preventive Maintenance .................................................
Chapter 7 EN/LZT 790 0005 R1A 7-2 BLANK.
Chapter 7 7.1 Introduction This chapter provides the schedules and instructions, where applicable, for routine inspection, cleaning and maintenance of the equipment which should be performed by an operator. There are also some basic fault-finding procedures to follow in the event of a suspected unit failure 7.
Chapter 7 2. If liquid has been spilled , or objects have fallen into the product. 3. If the product has been exposed to rain or water. 4. If the product does not operate normally by following the operating instructions.
Chapter 7 7.3.3 Levels of Continuing Ericsson Service Support For stand-alone equipment, then Ericsson BASIC Essential Support is the value for money choice. BASIC provides you with year-by-year Service long after the warranty has expired. For systems support you can choose either Gold Business Critical Support or Silver Business Advantage .
Chapter 7 7.4.3 Preliminary Investigations Always investigate the failure symptoms fully, prior to taking remedial action. Fault diagnosis for the equipment operator is limited to the following tasks, since the operator should NOT remove the covers of the equipment: 1.
Chapter 7 Warning! Before replacing the rear panel fuse, disconnect the unit from the supply. Failure to do this may expose hazardous voltages. Unplug the unit from the local supply socket. 1. Ensure that power is turned off and the power cable is disconnected from the AC power inlet.
Chapter 7 7.4.6 Summary Status LED Unlit If the Summary Status LED is unlit, fault-find the problem as detailed in Table 7.2 . T able 7.2 Su mmary S tatus LED Unlit Fault-finding Step Action If Result of Action is Yes… If Result of Action is No… 1 Check Status LED .
Chapter 7 T able 7.3 Fans Not Working/Overheating Step Action If Result of Action is Yes… If Result of Action is No… 1 Check Fan Rota tion . Inspect the fans located at the sides of the enclosure. Are the fans rotating? Check the temperature (select Chassis / Temperature Alarms on the Device Info web page ).
Chapter 7 EN/LZT 790 0005 R1A 7-10 7.5.2 Equipment Dispose of this equipment safely at the end of its life. Local codes and/or environmental restrictions may affect its disposal.
A Glossary Annex A The following list covers most of the abbreviations, acronyms and terms as used in Ericsson Manuals, User and Reference Guides. All terms may not be included in this Reference Guide. μ m Micrometre (former name - micro n): a unit of length equal to one millionth (10-6) of a metre.
Annex A AMOL I and II Automatic Measure of Line-ups I and II: Used by automated equipment to measure programme-view ing ratings. ARP Address Resolution Proto col. A protocol used to "resolve" IP addresses into underlying Ethernet MAC addresses.
Annex A Bouquet A collection of services (TV, radio, and data, or any combination of the three) grouped and sold together, and identified i n the SI as a group.
Annex A Chrominance The colour part of a TV picture signal, rel ating to the hue and saturation but not to the luminance (brightness) of the signal. In a composite-coded colou r system, the colour inf.
Annex A DCE Data Communications Equipment: Typically a modem . It establishes, maintains an d terminates a session on a network but in itself is not the source (originator) or destination (end receiving unit) of signals (e.g. a computer, see DTE ). A DCE device may also convert signals to comply with the tran smission path (network) format.
Annex A DSNG Digital Satellite News-Gathering. DSP Digital Signal Processor. DTE Data circuit Terminating Equipment: A communications device that originates (is the source) o r is the end receiving unit (destination) o f signals on a network. It is typically a terminal or com puter.
Annex A Encryption Encoding of a transmission to prevent acce ss without the appropriate decryption equipment and authori zation. EPG Electronic Programme Guide: On -screen prog ramme listing using thumbnail pictures and/or text. Ethernet The most widely used local area net work (LAN) defined by the IEEE as the 802.
Annex A GUI Grap hical User Interface: The use of pictures rather than just words to represent the input and output of a program. A program with a GUI runs under a windo wing system and has a screen interface capable of displaying grap hics in the form of icons, drop-down menus and a movable poin ter.
Annex A IP Internet Protocol: The IP part of TCP/IP. IP implements the network layer (layer 3) of the protocol, which contains a network add ress and is used to route a message to a different network or sub-net work.
Annex A JPEG Joint Photographic Experts Gr oup: ISO/ITU standard for compressing still images. It has a hig h compression capability. Using discrete co sine transform, it provides use r specified compression ratios up to around 1 00:1 (there is a trade-off betwe en image quality and file size).
Annex A MEM Multiplex Element Manager: A GUI-based control system, part of the range of Ericsson AB compressi on sy stem control element produ cts. The evolution 5 000 MEM holds a model of the system hardware. Using this model, it controls the individual system ele ments to configure the output multiplexes from the incomin g elementary streams.
Annex A Multicast An IP mechanism that allows transmissi on of data to multiple receivers. A multica st can also have sev eral transmit sourc es simultaneously. In video applications , mu lticast is typically used to distribute a video signal from a central source to multiple destinations.
Annex A OFDM Orthogonal Frequency Division Multipl ex: A modulation technique used for digital TV transmissi on in Europe, Japan and Australia; more spectrally efficient than FDM. In OFDM, data is di stributed over a large number of carriers spaced apart at pre cise frequencies.
Annex A PES Packetised Elementary Stream: A sequential stream of data bytes that has been converted from origin al elementary streams of audio and video access units and transpo rted as packets. Each PES packet consists of a header and a payload of variable length and subject to a maximum of 64 kbytes.
Annex A P R P B Analogue Colour difference signal s. Refer to C R C B for an explanation. PROM Programmable Read-Only Memory: A device, whi ch may be written once with data for permanent st orage, and then re ad whenever required.
Annex A ROM Read Only Memory: A non-volatile storage device for digital data. Data has been stored permanently in this devi ce. No further information may be stored (written) there and the data i t holds cannot be erased. Data may be read as often as required.
Annex A STB Set-Top Box: A box that sits on top of a television set and is the interface between the home television and the cable TV company. New technologies evolving for set-to p boxes are video-on-dem and, video games, educational service s, database searches, and home shopping.
Annex A SNTP Simple Network Time Protocol is an Internet protocol used to synchronize the clocks of computers to some time reference. It is a simplified version of the protoc ol NTP protocol which i s too complicated for many systems.
Annex A UART Universal Asynch ronous Receive r Transmitter: A device providing a serial interface for transmitting and recei ving data. UDP User Datagram Protocol. A protocol above the IP layer that provides port multiplexing in addition. In essence, you can transmit IP data packets to several receiving pro cesses in the same unit/device.
Annex A EN/LZT 790 0005 R1A A-20 Y (Luminance) Defines the brightness of a particular point on a TV line. The only signal required for black and white pi ctures. Y/C Broadcast video with separate colour, Y (luminance) a nd C (Chroma) (sometimes calle d S-Video).
B T echnical S pecification Annex B Contents B.1 Output ................................................................................................... B-3 B.1.1 Supported Video Resolutions .........................................................
Annex B EN/LZT 790 0005 R1A B-2 B.8 Cable Types ....................................................................................... B-20 B.9 Compliance ........................................................................................ B-21 B.
Annex B B.1 Output B.1.1 Supported Video Resolutions The RX8000 Receiver supports MPEG-2 and MPEG-4 AVC, 4:2:0. T able B.1 Supported Video Resolutions Input Resolutions (H x V) Frame-Rates Output Format (H x V) Specification 1920 x 1080 1440 x 1080 1280 x 1080 960 x 1080 29.
Annex B B.1.3 Composite Video Output The equipment supports video decoding as per ITU-R BT.470 and ANSI/SMPTE 170M. Table B.3 625 Line Description Test Signal Limit Bar Level VITS17 700mV +/- 7mV Bar Tilt VITS17 <0.
Annex B Description Test Signal Limit DC Offset NTC-7 comp +/- 100mV Chrominance to Luminance Gain Inequality NTC-7 comp 100 +/- 5% Chrominance to Luminance Phase Inequality NTC-7 comp <20nS K factor K 2T NTC-7 comp <1% Pulse X bar K rating 100 +/ - 1% Frequency Response (MultiBurst) FCC Multi- burst 0.
Annex B Parameter Value for Y, R, G, B Value for Pb, Pr Condition Notes ± 1 dB 20 MHz to 30 MHz +1 dB/-2.5 dB MHz ± 1 dB Group delay DC to 30 MHz < 50nS DC to 30 MHz < 50nS Noise DC to 30 MHz .
Annex B B.1.5 HD SDI Digital Video HD SDI output supports: • Embedded Decoded Audios • Closed Captioning (EIA 708B) • VITC • VANC Table B.7 Digital Video Output Connectors Item Specification S.
Annex B B.2.2 MPEG Audio The RX8000 Receiver supports decoding of MPEG audio as follows: • Compression layers: MPEG-1 layers I and II • Sampling rate: 48 kHz • Maximum c ompressed data rate: 384 kbps (layer II) B.
Annex B Table B.8 Analogue Audio Performance Specifications Parameter Specification Safety status SELV Output connector Male 9 pin D-sub Output format Balanced Bit rates 32 kbps to 384 kbps Sampling rates 48 KHz Nominal Output Level 0dBu +/- 0.
Annex B B.3.3 Audio Routing The RX8000 Receiver supports the following routing of audio signals: • STEREO (Channel 1 left, Channel 2 right) • MIXED TO BOTH (Channel 1 and 2 on left and right) • .
Annex B Mono kbps Stereo kbps 80 160 96 192 112 224 128 256 160 320 192 384 B.3.7 Digital Audio Outputs Digital audio outputs comply with E1A-422 1 and have a maximum data rate of 3.072 Mbps. Digital audio is output on two 9-way, D-type and four BNC connectors.
Annex B Parameter Specification Tuning step 1 kHz Carrier frequency search range ± 1 to ± 5 MHz Receive spectrum sense Normal and inverted L-band Power Input power level per carrier -65 to –25 dBm.
Annex B Parameter Specification Miscellaneous DVB-S Phase noise tolerance 3 SSB phase-noise power spectral density < -68 – 10*log(Rs/20) dBc/ Hz at δ F = 10 kHz offset Phase noise power spectral.
Annex B Table B.13 DVB-S2 Satellite Input – DVB-S2 Es/No Ratio LDPC FEC Rate DVB-S2 Theoretical 5 Es/No Ratio (dB) in perfect linear channel for correct MPEG-2 system operation 1/2 QPSK 1.00 3/5 QPSK 2.23 2/3 QPSK 3.10 3/4 QPSK 4.03 4/5 QPSK 4.68 5/6 QPSK 5.
Annex B Table B.14 LNB Power and Control Parameter Specification Voltage V (nominal) Receiver Polarisation 6 Voltage 13 18 Vertical/circular right Horizontal/circular left Current 350 mA maximum LNB control 22 ± 2 kHz tone Tone amplitude 0.65 ± 0.2 Vp-p B.
Annex B B.4.3 DVB-ASI Input T able B.16: DVB-ASI Copper Input Specification Safety status SELV Connector type BNC, Female Input impedance 75 Ω Data rate range 0.350 - 160 Mbps Error decodin g None B.4.4 100/1000BaseT Dual NI C Input Receivers Table B.
Annex B Table B.18 Frame Sync Connector Item Specification Safety status SELV Connector type BNC, Female Connector designation Frame Sync Pin: Centre Analogue Black and Burst Input Shield Ground/Chassis B.5 Output S pecifications B.5.1 Video Outputs See: Table B.
Annex B Item Specification Voltage Maximum Switching Power 24 W / 60 VA Minimum Switching Load 0.1 mA, 100 mV AC B.5.4 DVB-ASI Output Table B.20: DVB-ASI Copper Input Specification Safety status SELV Connector type BNC, Female Input impedance 75 Ω Data rate range 0.
Annex B B.6 Environment al B.6.1 Conditions Table B.22 Environmental Conditions Operational Specification Tempera ture 0 ° C to +50 ° C ambient air temperature with free air-flow Humidity 0% to 95% .
Annex B B.7 Power Supply – AC Mains Input This equipment is fitted with a wide-ranging power supply. It is suitable for supply voltages of 100-240 V AC -10% +6% at 50/60 Hz nominal.
Annex B Table B.26 Suitable Signal Cable Types Signal Type Connector Cable Alarm Relay 9-way D-type Male Belden 8162 CM 2PR24 shielded E108998 (typical) ASI Out 1 and 2 BNC Canford Audio BBC 1/3 PSF (.
Annex B B.9.2 EMC 8 The equipment has been designed and tested to meet the following: EN 55022 and CISPR22 European International Emission Standard Limits and methods of measurement of radio frequency interference characteristics of information technology equipment - Class A.
Annex B DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility 1999/5/EC of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity.
Annex B Defines country of origin. The packaging is reusable per GB 18455-2001. This symbol guarantees that packagi ng with this symbol is recyclable and will be accepted by cardboard recyclers. Recyclable per GB 18455-2001. B.9.8 Materials Declarations Ericsson’s products are designed and manufactured in keeping with good environmental practise.
Annex B 50 It is assumed that while the product is in normal use, any batteries associated with real-time clocks or battery-backed RAM will be replaced at the regular in tervals. The EFUP relates only to the environmental impact of the product in normal use, it does not imply that the product will continue to be supported for 50 years.
Annex B EN/LZT 790 0005 R1A B-26 • First/Last name • Password request (6 numbers/characters). If you do not include this information one will be created for you.
C Language Abbreviations Annex C Contents C.1 ISO Languages .................................................................................... C-3 C.2 Non-ISO Languages ............................................................................ C-4 List of Tables Table C.
Annex C EN/LZT 790 0005 R1A C-2 BLANK.
Annex C C.1 ISO Languages Languages are shown in alphabetical order. T able C.1 ISO Language Codes NO LANGUAGE ABBREVIATION 5 ARABIC ARA BASA BAS 14 BENGALI BEN 135 CHINESE CHI 19 CZECH CZE 21 DANISH .
Annex C NO LANGUAGE ABBREVIATION 27 SPANISH SPA 112 SWEDISH SWE 117 THAI THA 123 TURKISH TUR 128 URDU URD 130 VIETNAMESE VIE C.2 Non-ISO Languages The following non-ISO 1 languages are supported.
Annex C The non-ISO languages allow tagging of audio without reference to specific languages. The system can then transmit two languages (Main and Auxiliary) which could be any type of audio. Note: The non-ISO languages need to be user-defined in the Encoder for them to be available.
Annex C EN/LZT 790 0005 R1A C-6 BLANK.
Ein wichtiger Punkt beim Kauf des Geräts Ericsson RX8000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ericsson RX8000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ericsson RX8000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ericsson RX8000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ericsson RX8000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ericsson RX8000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ericsson RX8000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ericsson RX8000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ericsson RX8000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
