Benutzeranleitung / Produktwartung 5010E des Produzenten Epson
Zur Seite of 84
PowerLite ® Home Cinema 5010/5010e Home Theater Projector User’ s Guide.
2 Contents Contents Introduction 5 Projector Parts 6 Remote Control 8 Optional Accessories 9 Registration and Warranty 9 Using This Manual 10 Setting Up the Projector 11 Choose a Location 11 Installin.
Contents 3 Locking the Projector 32 Making Detailed Adjustments 34 Using the Menu Syste m 34 Changing How the Menus Display 35 Adjusting the Picture Quality 36 Input Brightness Settings 36 Sharpness a.
4 Contents Maintenance 57 Cleaning the Lens 57 Cleaning the 3D Glasses 58 Cleaning the Projector Case 59 Cleaning and Replacing the Air Filter 59 Replacing the Lamp 61 Resetting the Lamp Usage Timer 6.
Introduction 5 Introduction The PowerLite ® Home Cinema 5010/5010e proje ctor lets you enjoy theater-quality 3D images in the re laxing environment of you r ow n home.
6 Introduction Projector Parts Air exhaust Proje ctor le ns Adjustable foot HDMI ports External 3D IR port Remote receiver Vertical lens shi ft dial Front Back Lamp cover Air intake Air filter cover P.
Introduction 7 Escape button Power button Mounting bracket attachment points Bottom Projector Control Panel Source button Menu navigation/ vertical keystone buttons Front adjustable feet Menu button E.
8 Introduction Remote Control Source buttons Switch between equipment connected to the projector On button Turns projector on Menu navigation buttons Color Mode button Quickly change color settings to.
Introduction 9 Optional Accessories Epson provides the following optional accessories for the projector: In addition to the accessories listed above, 1-year and 2-year extended service plans are available. You can purchase these plans and other accessories from an authorized Epson reseller.
10 Introduction Using This Manual This book contains all the information you need to use the projector, in addition to basic setup and maintenance instructions, troublesh ooting tips, important safety instructions, specifications, and warranty information.
Setting Up the Projector 11 Setting Up the Projector Follow the instructions in this section to ch oose a location for the projector, connect the cables, and display an image. Choose a Location You can install the projector for the viewing setups shown below, as well as rear pr ojection.
12 Setting Up the Projector Ideally, keep the projector level and place it at a height so its lens is centered between the top and bottom of the screen.
Setting Up the Projector 13 The size of the image is determined by the distance from the projector’s lens to the screen. Depending on your display settings and how yo u use the Zoom ring, the actual size may differ.
14 Setting Up the Projector To determine the exact image size when you know the proj ection distance (or the exact projection distance when you know the de sired image size), you can use the Image Size Calculator. This program is avai lable on the Epson website at epson.
Setting Up the Projector 15 Installing the Projector To install the projector, you first need to dete rm ine the location, based on the size of your screen (maximum diagonal image size). Use the tables on page 13 as a guide to pos itioning the projector.
16 Setting Up the Projector The following illustrations show the dimensions of the projec tor: LENS 11.8 in. (300 mm) 5.9 in. (150 mm) 3.3 in . (83 mm) 2.4 in. (60 mm) 6.3 in. (160 mm) 15.6 in. (396 mm) 18.3 in. (466 m m) 9.2 in. (233 mm) 3.3 in. (83 mm) 6.
Setting Up the Projector 17 Connecting the Cables Connecting Video and Computer Equipment You can connect the projector to many type s of video equipment, such as a Blu-ray Disc ™ /DVD player, digit al tuner, cabl e or satellit e box, video game console, camcorder, or digital camera.
18 Setting Up the Projector For best result s, connect your vide o equipment to the HDMI port, if possible. If your equipment doesn’t support HDMI, connect it to either the Component (for high quality, component video) or Video (for composite video) port.
Setting Up the Projector 19 Making Other Connections Connect the power cable and other cables described below, depending on how you plan to use the projector. ■ Plug the power cable into the projector and a grounded electrical outlet. ■ To use an AV controller with the projector, connect a 9-pin null modem serial cable to the RS-232C port.
20 Setting Up the Projector Installing Batteries in the Remote Control The remote control uses two AA batteries. Warning: Keep batteries away from children. If a ba ttery is swallowed, contact your doctor immediately. 1. Release the tab and lift open the cover.
Setting Up the Projector 21 The power light flashes while th e projector warms up. If you don’t see a picture, you may need to change the image sou rce as described on page 21. Turning Off the Projector 1. Turn off any equipment connected to the projec tor.
22 Setting Up the Projector If you press the source button on the projecto r, you see a list of available sources. Press the source button to move through th e list and select the desired source. Note: If an image does not appear, se e “Problem Solving” on page 66.
Setting Up the Projector 23 The vertical position (V) can be adjusted by up to 96% of the height of the screen, while the horizontal position (H) can be adjusted by up to 47% of the width of the screen. If one side of the image is taller than the other, make sure the projector is parallel to the screen.
24 Setting Up the Projector When setting up the projector, make sure that it is placed level to the screen in order to provide the best possible image quality. If you must set up the projector at an angle, use the vertical keystone buttons to correct the image shape.
Making Basic Adjustments 25 Making Basic Adjustments Follow the instructions in this chapter to make basic adjustments to the image shape, size, color, and quality. For further refinements, see “Making Detailed Adjustments” on page 34. Focusing and Zooming Use the focus ring to sharpen the image.
26 Making Basic Adjustments Choosing the Aspect Ratio In many cases, video signals are automatically resized to fit on your screen when Auto is selected as the Aspect setting. You may ne ed to change the size of the imag e (or aspect ratio) for certain image types by pressing the Aspe ct button on the remote control.
Making Basic Adjustments 27 Viewing 3D images To view 3D content, you must first connect a 3D-compatible video device to one of the HDMI ports on your projector. You will also need a pair of Epson or Epson-compatible M-3Di active shutter glasses. 1. Turn on and begin playback on the 3D-compatible video device.
28 Making Basic Adjustments Projecting in Split Screen mode You can use the Split Screen fe ature to simult aneously project two images from different image sources next to each other. You can cont rol the Split Scre en feature using the remote control or the projector menus.
Making Basic Adjustments 29 2. Press the Menu button. You see this screen: 3. To select an input source for the other image, select the Source setting, press Enter , select the input source, select Execute , and press Ent er . (You can also change image sources, if necessary.
30 Making Basic Adjustments Select the image source you want to adjust, then press the Color Mode button on the remote control. Choose from these settings: ■ Cinema for viewing movies in a dimly lit room. ■ Dynamic for projecting the brightest picture available.
Making Basic Adjustments 31 Adjusting the Gamma Setting You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your image or a displayed graph. Lower values will incr ease the contrast of dark areas, but tend to blur the bright areas.
32 Making Basic Adjustments Adjusting RGBCMY Use this feature to adjust the hue, saturation , and brightness for e ach of the red (R), green (G), blue (B), cyan (C), magenta (M), and yellow (Y) color components. 1. Press the RBGCMY button. You see the following displayed on the screen: 2.
Making Basic Adjustments 33 ■ Child Lock to disable the P power button on the projector’s control panel unless it is pressed for about 3 seconds. Since you can st ill use the remote cont rol to turn on the projector, you may want to keep it away from children’s reach.
34 Making Detailed Adjustments Making Detailed Adjustments You can use the projector’s on-scree n menus to make detailed adjustment s to the image quality—such as the brightness, contrast, sharpness, and color. You can also change the menu display, sleep mode settings, and other projector features.
Making Detailed Adjustments 35 4. When you’re finished, press the Esc button to return to the previous menu or press the Menu button to exit th e menu system. To display one of the line menus, press the Enter button. You see a display like this at the bottom of the image: ■ Press the l or r button to adjust the setting.
36 Making Detailed Adjustments Adjusting the Picture Quality Before fine-tuning the image using these adjustments, make sure you have already se lected the best Color Mode for your picture and viewing environment, as described on page 29. Then use the settings in this section to finish adjusting the picture to your liking.
Making Detailed Adjustments 37 ■ Auto Iris When this setting is on, the light output is automatically adjusted according to th e brightness of the image. Select either Normal or High Speed to indicate how quickly you would like the projector to respond to changes in the brightness of the image.
38 Making Detailed Adjustments Sharpness and Picture Quality Set tings If the image looks fuzzy, or if it contains noise or flickering, you can use these settings to correct it. ■ Sharpness Use this function to make lines and edges appe ar more distinct in the image.
Making Detailed Adjustments 39 ■ Noise Reduction Note: This is not be available with a si gnal input through the PC port. This setting reduces flickering of analog im ages.
40 Making Detailed Adjustments ■ Abs. Color Temp. Shifts the color balance between red and blue, making the image appear warmer or cooler. ■ Skin Tone Makes fine adjustments to the tint and controls the amount of red or green in the image. Also useful for correcting black-and- white images, if they look tinted.
Making Detailed Adjustments 41 ■ Gamma You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to blur the bright areas.
42 Making Detailed Adjustments ■ 3D Format Use this setting to select the 3D format support ed by your video device. In most cases, the projector will correctly detect the 3D format when this option is set to Auto . You should only select the 2D , Side by Side , or Top and Bottom formats when your projector doesn’t properly display 3D images.
Making Detailed Adjustments 43 Adjustments for Computer Images In addition to the settings described previously, you can adjust the Tracking and Sync settings for analog RGB computer images. Normally, thes e settings are adjusted automatically by the projector.
44 Making Detailed Adjustments WirelessHD Settings (PowerLi te Home Cinema 5010e only) Use these options to m anage the Wireless HD connection and access the WirelessHD reception monitor. ■ Device Connections Select this option to display a list of available WirelessHD devices.
Making Detailed Adjustments 45 ■ Erase Device Name Use this option to delete the names of devi ces displayed in the WirelessHD Device Connections menu and return them to their default values. ■ Reset Select this option to reset al l WirelessHD settings and return them to their default values.
46 Making Detailed Adjustments Once you have finished making your selections for both screens, select Execute to exit the Source menu and apply these settings. Note: Certain combinations of sources can’t be se lected. Invalid input combinations will be grayed out.
Making Detailed Adjustments 47 Selecting Memory Settings You can easily recall the memory settings by using the Memory button on the remote control. 1. Press the Memory button on the remote control. 2. Select Load Memory . 3. Use the arrow buttons to select the desired settin g, then press the Enter button.
48 Making Detailed Adjustments Deleting Saved Memory Settings You can clear all your me mory settings at once. 1. Press the Menu button on the remote control. 2. Open the Reset menu, then select Reset Memory . 3. Select Yes , then press the Enter button to delete the memory settings.
Making Detailed Adjustments 49 3. Do one of the following: ■ Select Reset Lamp Hours to clear the lamp usage timer and reset it to zero. You should reset the lamp timer only when you install a new projector lamp. See page 64 f or more in formation. ■ Select Reset Memory to clear all memory settings.
50 Making Detailed Adjustments ■ Aspect This setting lets you change the aspect ra tio of your image, and works the same as pressing the Aspect button on the remote control.
Making Detailed Adjustments 51 Other Setup Options ■ Projection You can select different options for projecting th e image: Front , Front/Ceiling , Rear , Rear/Ceiling . ■ Direct Power On Sets projection to start without pressing the P power button on the projector or the On button on the remote control.
52 Making Detailed Adjustments ■ Child Lock Lets you lock the P power button on the projector’s co ntrol panel to make it more difficult for a child to turn on the p rojector.
Using WirelessHD 53 Using WirelessHD You can use the included Wire lessHD Transmitter (PowerLite Home Cinema 5010e only) to wirelessly stream HD content from a video device to the projector. Placing the WirelessHD Transmitter Place the WirelessHD Transmitter so that the unit’s light s face the front of the projector.
54 Using WirelessHD Setting Up a WirelessHD Connection To prepare your device to work with the WirelessHD button, follow these steps: 1. Follow the instructions on the previous page and place the t ransmitter within range of the projector. 2. Plug the AC adapter into the transmitter and an electrical outlet.
Using HDMI Link 55 Using HDMI Link When you connect HDMI CEC-compatible devices to the projector with HDMI cables, you can control them using the HDMI Link control buttons on the projector’s remote control. This lets you use just one remote control to op erate many commonly used features on all your devices.
56 Using HDMI Link 4. Set up your connected devices so their HD MI CEC-compatible fu nctions are enabled. For details, refer to the device manuf acturer’s documentation. Changing HDMI Link Settings 1. Press the HDMI Link button on the projector’s remote control.
Maintenance 57 Maintenance Your projector needs little maintenance. All you ne ed to do on a r egular basis is keep the lens clean. You also may need to clean the air filte r to prevent overheating. Warning: Before cleaning any part of the projector, tu r n it off and unplug the power cord.
58 Maintenance Caution: Never rub the lens with abrasive materials. Use only l ens cleaning fluids that are designed for cleaning optics. Avoid touching the lens with your bare hands to prevent fingerprints on or damage to the lens surface.
Maintenance 59 Cleaning the Projector Case Before you clean the case, turn off th e projector and unplug the power cord. ■ To remove dirt or dust, wipe the ca se with a soft, dry, lint-free cloth. ■ To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent.
60 Maintenance 4. Remove the air filter as shown. 5. Gently tap both sides of the air filter against a hard surface four or five times to remove loos e dust from the air filter. Note: Do not use excessive force when tapping the air filte r, or it may crack and become unusable.
Maintenance 61 8. Insert the outer edge of the air filter cover into the notches on the projector, then press in on the inner edge of the cover to lock it into place, as shown below. Replacing the Lamp The projection lamp lasts for u p to 4000 hours in Norm al mode.
62 Maintenance Follow these steps to replace the lamp: 1. If the projector is on, press the P power button on the projector twice or the Standby button on the remote control and wait for the power light to stop flashing. 2. Turn off the power switch on the back of the projector and unplug the power cord and any cables.
Maintenance 63 7. Lift up the lamp handle and gently pull the lamp out of the projector. Warning: The lamp(s) in this product contai n mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 8.
64 Maintenance 10. Tighten the lamp cover screw. 11. Reset the lamp usage timer, as describe d on page 64. Resetting the Lamp Usage Timer After replacing the lamp, plug the projector back in, turn on the power switch on the back of the projector, and press the P power button on the projector or the On button on the remote control.
Maintenance 65 2. Use the menu navigation buttons to open the Info menu. The following information appears: Note: The information displayed depends on the currently selected image source. The Lamp Hours shows 0H until you’ve used the lamp for at least 10 hours.
66 Problem Sol ving Problem Solving This section explains how to interpret the projector’s status lights, solve problems with the picture and remote control, and contact technical support. What To Do When the Lights Come On or Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs.
Problem Solving 67 Power light flashes blue, power bu tton is on The projector is warming up. Wait for the picture to appear. The projector is cooling down. Wa it unti l the power light stops flashing and remains off. Then press the P po wer button on the projector or the On button on the remote co ntrol to turn it back on.
68 Problem Sol ving Solving Picture Problems You cannot turn on the projector. ■ Make sure the power cord is connected and th e power switch on the back of the projector is t u r n e d on . T h e n w a i t a m o m e n t f or th e P power button to light up before pressing the P power button on the projector or the On button on the remote control.
Problem Solving 69 3D content does not display or does not display correctly. ■ Press the 2D/3D button on the remote control to switch to 3D viewing mode, if necessary. ■ Make sure you are within the 3D viewing range ( see page 11). ■ Check that your video device and media are both 3D-compatible.
70 Problem Sol ving ■ If the function key doesn’t let you display simultaneously on both screens, you might need to use the Display utility in the Windows Control Panel to make sure that both the LCD screen and exte rnal moni tor port are enabled.
Problem Solving 71 ■ There may be dirt on the lens. Clea n the le ns as descr ibed on page 57. ■ Adjust the focus (see page 25). ■ Make sure the lens is not fogged by condensat ion. If you’ve just moved the projector from a cold environment, wait a couple of minutes before using it.
72 Problem Sol ving Solving Remote Control Problems The projector doesn’t respond to remote control commands. ■ Make sure you’re within about 32 feet (10 m) of the projector, and the remote control is aimed at the projector’s front or back sensor within the ranges shown below.
Problem Solving 73 Solving WirelessHD Problems The projector cannot display images from the Wirel essHD Transmitter. ■ Open the WirelessHD reception monitor an d check the strength of the WirelessHD signal (see page 44).
74 Problem Sol ving Where to Get Help Internet Support Epson provides technical assistance 24 hours a day at epson.com/support (U.S.) or epson.ca/support (Canada). Here you can access troubleshooting information, download product documentation, and receive technical advice through email .
Specifications 75 Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels 0.74 inch (18.8 mm) wide Lens F=2.00 to 3.17 Resolution (native format) 1920 × 1080 pixels, .
76 Specificati ons Remote Control Range Approximately 32 feet (10 m) Batteries AA × 2 WirelessHD Transmitter (Pow erLite Home Cinema 5010e only) Usable frequency 60 GHz band (2 – 3 ch) AC adapter 4.75 – 5.25 V DC Transmission range 32 feet (10 m) WirelessHD standards Conforms to WirelessHD Ver.
Specifications 77 Electrical Rated frequency 50/60 Hz AC Power supply 100 to 120 V AC: 2.9 A 200 to 240 V AC: 1.3 A Power consumption 100 to 120 V AC: Operating: 352 W (Normal mode) 262 W (ECO mode) Standby: 0.25 W (with HDMI Link enabled) 220 to 240 V AC: Operating: 342 W (Normal mode) 252 W (ECO mode) Standby: 0.
78 Specificati ons Compatible Video Formats The projector supports analog video in NTSC, PAL, and SECAM formats, and it automatically adjusts to the incoming signal. It can receive these format s as composite or component video—which it accepts through the Video and Component ports, respectively.
Specifications 79 Analog RGB (computer display) HDMI 3D mode Note: When proj ecting with WirelessHD, DeepC olor 1080 P 50/60Hz is not supported. ESC/VP21 Command Codes You can use an AV controller with a 9-pin null mode m serial cable to control the p rojector.
80 Notices Notices Important Safety Information Follow these safety instructions when setting up and usi ng the projector: ■ Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on.
Notices 81 ■ The following people should limit 3D content viewing: People with a history of photosensitivity People with heart disease People in poor health People who are sleep deprived People who .
82 Notices ■ Allow the lamp to cool for one hour before replacing it. ■ Unplug the projector during lightnin g storms or when not in use for extended periods.
Notices 83 WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment.
84 Notices Trademarks Epson, PowerLite, and C 2 Fine are registered tradem arks, 1080Perfect is a tradem ark, and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademar k, DigiScan and AccuCinema are trademarks, and Ex tra Care and Epson Connection are service marks of Epson America, Inc.
Ein wichtiger Punkt beim Kauf des Geräts Epson 5010E (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Epson 5010E noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Epson 5010E - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Epson 5010E reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Epson 5010E erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Epson 5010E besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Epson 5010E verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Epson 5010E. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Epson 5010E gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
