Benutzeranleitung / Produktwartung 667 des Produzenten Emerson Process Management
Zur Seite of 24
www.Fisher.com D10031 1X012 Type 6 67 Diaphragm A ctuators S i z e 80 and 10 0 Contents Introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scope of Manual 1 . . . . . . . . . . . . . . . . . . . . . . . . . Description 2 . . .
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 2 Table 1. Specifications SPECIFICATION ACTUATOR SIZE SPECIFICATION 80 100 Nominal Effective Diaphragm Area cm 2 1761 2902 Nomi.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 3 Figure 2. Schematic Representation of Type 667 Actuator DIAPHRAGM AIR LIFTS SPRING PUSHES DOWN ACTUA TOR STEM TYPE 667 REVERSEĆACTING DIAPHRAGM ACTUA TOR AF3833-A A6127 / IL increases valve seat load on valve applications where additional seat-loading is necessary.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 4 When an actuator and valve are shipped together, the actuator is normally mounted on the valve. Follow the valve instructions when installing the control valve in the pipeline.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 5 Adjustments Travel Make travel adjustments when the motion observed during actuator travel is different from the travel stamped on the actuator nameplate. If the Actuator Mounting procedure was followed correctly, this adjustment should not be necessary.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 6 For high spring forces, it is necessary to use spacers between the bottom of the yoke and the spring seat to isolate spring force from the adjusting nut.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 7 D Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the actuator cannot suddenly open or close the valve. D Use bypass valves or completely shut off the process to isolate the valve from process pressure.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 8 10. For actuators with a snubber (see figure 8): W ARNING To avoid personal injury due to the sudden, uncontrolled movement of parts, ensure the actuator spring is not under compression before removing the travel stop.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 9 Figure 4. Size 80 Actuator Construction CAP SCREW (KEY 12) SP ACER (KEY 2) UPPER DIAPHRAGM CASE (KEY 1) DIAPHRAGM (KEY 3) LOW.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 10 diaphragm. Do not exceed 68 N S m (50 lbf S ft) torque. 11. Insert the cap screws (key 13) into the diaphragm casing, and tighten the hex nuts (key 14) in the following manner.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 11 These instructions outline the procedure required to decrease high spring compression. Loosen the jam nut (key 26), and rotate the adjusting nut (key 25) until spring compression is relieved.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 12 Figure 5. Size 100 Actuator Construction DIAPHRAGM CASING COVER (KEY 15) UPPER DIAPHRAGM PLA TE (KEY 4) UPPER DIAPHRAGM CASI.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 13 spring interferes with installation of the lower diaphragm casing, reposition the spring by rotating the adjusting nut (key 25). 4. Install the lower diaphragm casing, and secure it by tightening the four hex nuts.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 14 For Actuators With the Top-Loaded Option Disassembly For key number locations refer to figure 7, and refer to the Top-Loaded Actuator Detail shown in figure 7. Also, refer to figure 5 for diaphragm construction details.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 15 when the diaphragm adaptor (key 245, fig ur e 5) is in st all ed . CAUTION If the diaphragm (key 3) is installed so air pressure is applied to the fabric side, it will immediately delaminate the sealing surface (smooth surface) from the fabric.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 16 18. Insert the cap screws (key 13) into the upper diaphragm casing (key 1), and finger tighten the screws. 19. Tighten the cap screws (key 13) in the following manner. The first four cap screws tightened should be diametrically opposed and 90 degrees apart.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 17 worm shaft (key 51). Thread the handwheel cap (key 127) onto the worm shaft.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 18 Assembly 1. The front and back worm retainers (keys 48 and 49) each have a slot in their threads for a set screw (key 52). Pack the ball bearings (key 50) with lithium grease, and insert one ball bearing into the back worm retainer (key 48).
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 19 Key Description Part Number 8* O-Ring, nitrile (2 required) Size 80 1D542906992 Size 100 1H8627X0042 9* O-Ring, nitrile Size.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 20 Key 18 Spring, steel ACTUATOR SIZE RANGE TRAVEL COMPRESSION RATE MAXIMUM LOAD PART NUMBER COLOR CODE SIZE bar psi mm Inches N/mm Lb/in N Lb NUMBER CODE 0.2-1 3-15 76 3 175.1 1000 25,042 5630 1H747727082 Red 0.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 21 Figure 6. Size 80 Type 667 Actuator NOTE: KEYS 243, 244, 245, AND 246 ARE NOT SHOWN.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 22 Figure 7. Size 100 Type 667 Actuator NOTES: THIS P ART IS LOCATED 90 _ T O FRONT OF POSITION SHOWN 2.
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 23 Figure 8. Size 80 Type 667 Actuator with Side-Mounted Handwheel and Hydraulic Snubber VIEW A SECTION BĆB B B VIEW A APPL Y .
667 Size 80 and 100 Actuators Instruction Manual Form 1432 December 2007 24 Figure 9. Size 100 Top-Mounted Handwheel APPL Y LUB 50A2624-F / DOC Emerson Process Management Marshalltown, Iowa 50158 USA Cernay 68700 France Sao Paulo 05424 Brazil Singapore 128461 www.
Ein wichtiger Punkt beim Kauf des Geräts Emerson Process Management 667 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Emerson Process Management 667 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Emerson Process Management 667 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Emerson Process Management 667 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Emerson Process Management 667 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Emerson Process Management 667 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Emerson Process Management 667 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Emerson Process Management 667. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Emerson Process Management 667 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
