Benutzeranleitung / Produktwartung Liebert IntelliSlot IS-WEB485ADPT des Produzenten Emerson
Zur Seite of 60
Monitoring For Business -Critic al C ontinuity™ Li eber t ® Inte lliS l ot ® Web Ca r d s Install ation Man ual – Lie bert Inte lliSl ot W eb C ard, Liebe r t Int elliSlo t W eb C ard-LB, Lieber.
.
i T ABLE OF CONTENTS I MPORT ANT S AFETY I NSTRUCTION S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.0 I NTRODUCTI ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii 9.0 S UPPORT I NFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 9.1 View Web Card Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 I MPORT ANT S AFETY I NSTRUCTIONS SAVE THESE INSTRUCTIONS ! WARNING Only a qualified service profe ssional should inst all these products. Liebert recommends having an Emerson Network Power Liebert Servic es representative perf orm the installation in large UPSs.
Introd uction 2 1.0 I NTRODUCTION The Liebert ® IntelliSlot ® Web Card family delivers enhanced communications and control to Liebert AC Power and Precision Cooling systems. Liebert IntelliSl ot Web cards bring SNMP, Telnet and Web-management capabi lity to many models of Liebert power a nd cooling equipment.
Introd uction 3 1.2 Web Support The Liebert IntelliSlot We b card delivers Web management and control to Liebert equipment. All authorized users on your network w ill be able to view status informatio n. 1.3 Password Protection Control and configurati on capabilities are p rotec ted by a username and password combination.
Installation 4 2.0 I NST ALLATION 2.1 Inst all a Liebert IntelliSlo t W eb Card—Non-Adapter V ersion Follow these steps to install a Liebert IntelliSlot Web card (non-adapter version—P/N I S-WEBCARD, IS-WEBLB and IS-WEBLBDS). 1. Locate the Liebert IntelliSlot option bay on your Lieb ert equipment—You might need to remove a plastic cover.
Installation 5 2.2 Inst all a Liebert IntelliS lot Web/485 Card With Adapter Follow these steps to install a Liebert IntelliSlo t Web/485 Card With Adapter (P/N IS-WEB485ADPT). • Locate the adapter mounting loca tion in your Liebert e quipment. • Secure the Liebert IntelliSlot Web/485 Card With Adapter with the supplied screws.
Configur ation Over view 6 3.0 C ONFIGURATION O VERVIEW You may use any of the following inte rfaces to configure the Web card: Each config uration section provides in structions using the Terminal Em.
Configur ation Over view 7 3.2 Open the T erminal Emulation Interface - Serial Connection To access configuration using term in al emulation software with a serial connection to the Web card: 1. Open a terminal emulation applicati on, such as HyperTerminal.
Configur ation Over view 8 3.3 Open the T erminal Emulation Interface - TCP/IP Connectio n To access configuration using term in al emulation software with an Ethernet connection to the Web card: 1. Open a terminal emulation applicati on, such as HyperTerminal.
Configur ation Over view 9 3.4 Open the T elnet Interface To access configuration using Telnet: 1. Open a Telnet connection on a computer with an Ethernet c onnection to t he Liebert unit. To do this: • Open a command prompt window—click the Start button, then Run .
Configur ation Over view 10 3.5 Open the W eb Interface To access configuration using the Web interface: 1. Open a Web browser such as Internet Explorer, then enter the IP address or hostname of the Web card in the address bar—e.g., http://192.168.0.
System Information 11 4.0 S YSTEM I NFORMATION System Information is optional an d identifies the Liebert unit, its location, a contact person an d othe r information about the unit. The default value of each fi eld is “Uninitialized.” T e rminal Emulation (Serial or TCP/IP Connection) / T elnet To edit any field in this category: 1.
Network Settings 12 5.0 N ETWORK S ETTINGS The IP Network Settings Menu is used to enable network communications with the Web card. Refer to the foll owing sections for de tailed step-by-step instructions on each item from this menu: T able 8 N etwork Settings menu guide Menu item Refer to: 5.
Network Settings 13 5.1 Boot/IP Settings The Boot/IP Settings Menu is used to set parameters for network access to the Web card. Consult your network administrator for these settings. T e rminal Emulation (Serial or TCP/IP Connection) / T elnet To change any pa rameter: 1.
Network Settings 14 5.2 Domain Name Ser ver (DNS) Settings The Domain Name Server settings menu configures the servers the Web card will use for hostname resolution.
Network Settings 15 Web Interfac e To access the DNS menu th rough the Web interface: • Click on the Configure tab, then Network Settings in the left panel an d finally Edit beneath the table of parameters and descript ions. Af ter making changes, click Save .
Network Settings 16 Web Interfac e To access Management Protocol se ttings through the Web interface: • Click on the Configure tab, then M anagement Protocol in the left panel a nd finally Edit in the right panel.
Network Settings 17 SNMP Communications Menu Use the SNMP Communications Menu to enable au thentication traps and vi ew or change communi- ties and trap communities , events and parameters. For details on viewing support information, s ee 9.2 - Events and Parameters .
Network Settings 18 Display/Modify T rap Communities View devices that are configured to receive notifications from the We b card, identified by IP address or hostname, trap listen port and community string . Up to 20 de vices may be configured to receive traps.
Network Settings 19 5.4 Web Server Use the Web Server Menu to configure access to the card through the Web interface. Co nsul t your network adminis- trator if needed. 5.4.1 S pecify W eb Server Settings T e rminal Emulation (Serial or TCP/IP Connection) / T elnet To change any pa rameters: 1.
Network Settings 20 5.4.2 Inst all Security Certificates - Internet Explore r 6 or earlier If you use Internet Explorer 6 or an earlier version and select HTTPS as the operation mode of the Web server (see 5.4.1 - Specify Web Server Settings ), follow these instructions to install a security certificate.
Network Settings 21 • In the Certificate win dow, click the Install Ce rtificate button, a s shown below. • The Certific ate Import Wizard open s. Click Next . • Click on Automatically select the certif icate store based on the type of certificate , then click Next .
Network Settings 22 5.4.3 Inst all Security Certificates - Internet Explore r 7 or later If you use Internet Explorer 7 or later and select HTTPS as the operation mode of the Web server (see 5.4.1 - Specify We b Server Settings ), follow these instructi ons to install a security certificate.
Network Settings 23 • In the Certificate win dow, click the Install Ce rtificate button, a s shown below. • The Certific ate Import Wizard open s. Click Next . • Click on Automatically select the certif icate store based on the type of certificate , then click Next .
Network Settings 24 5.5 T elnet Server Use the Telnet Server Menu to enab le or disable access to the Web card through a Telnet interface. T e rminal Emulation (Serial or TCP/IP Connection) / T elnet To change this setting: 1. Choose IP Network Settings from the Main Menu, then Telnet Server .
Network Settings 25 T e rminal Emulation (Serial or TCP/IP Connection) / T elnet To change this setting: 1. Choose IP Network Settings from the Main Menu, then Time (SNTP) . 2. Choose SNTP Time Synch Rate, then specify: • Hourly •D a i l y 3. Choose Time Server, then specif y the new time server, if desired.
Network Settings 26 5.7 Change Username / Password The Web card is designed for two types of access, each wi th a defa ult user name and password. For security, be sure to chan ge the default password. Follow these guid elines to change the use r name and password.
Network Settings 27 5.8 Reset Authentication to Factory Default s You may reset the Administrator an d General Use r usernames and passwords to the factory defaults. If you forget your us ername or password, you ma y reset them using a seri al configuration cable connection (see Section 2.
Messaging 28 6.0 M ESSAGING The Messaging menu is used to set up e-mail and text message notifications from the Web card. T e rminal Emulation (Serial or TCP/IP Connection) / T elnet To access these options: 1. Choose Messaging from the Main Men u. 2.
Messaging 29 6.1 E-Mail Configuration Setting up event notifications to be sent via e-mail involves two steps: enabling the function, then specifying the parameters. T e rminal Emulation (Serial or TCP/IP Connection) / T elnet To activate and set up e-mail messages: 1.
Messaging 30 Web Interfac e To access E-Mail Configura tion through the Web interfa ce: • Click on the Configure tab, then Email in the left panel and finally Edi t in the right panel.
Messaging 31 T e rminal Emulation (Serial or TCP/IP Connection) / T elnet To activate and set up SMS messages: 1. Choose Messaging from the Main Menu, then SMS . 2. To enable the SMS feature, enter y (yes) at the prompt. 3. Choose SMS Configuration from the Messaging Menu, then select an option and use the following g uide to make change s.
Messaging 32 6.3 Customize Messages Both e-mail and SMS text messages may be custom- ized to include items such as the IP address or host- name, event name and a link to the Web card in the body of the message. T e rminal Emulation (Serial or TCP/IP Connec- tion) / T elnet 1.
Messaging 33 Web Interfac e To access Customize Message se ttings through th e Web interface: • Click on the Configure tab, then Customize Messages i n the left panel and finally Edi t in the right panel. Choose the items to include in each type of message in the Email and SMS columns.
Factory Settings 34 7.0 F ACTORY S ETTINGS Factory default values may be re stored fo r all configuratio n settings. This step: • Replaces all user-d efined settings described in this manual (see 3.
Factory Settings 35 7.2 Liebert DS - Local Node Settings for Multiple Cards If you use two cards of the same ty pe with the Liebert DS, you will n eed to change th e local node set- ting of one card.
Monitor and Control Functions - W eb Only 36 8.0 M ONITOR AND C ONTRO L F UNCTIONS - W EB O NLY Web Interfac e Only The Web interface allows you to monitor and con t rol the Liebert equipment where the Web card is installed, in additi on to configuration c apabi lities presented in previous sections.
Monitor and Control Functions - W eb Only 37 8.2 Controlling Liebert Equipment To perform Control operations through the Web interface: • Open the Web interface (if needed, see 3.5 - Open the Web Interface ). • Click on the Control tab, as shown in the following example.
Monitor and Control Functions - W eb Only 38 8.3 Event Log The Event Log tab allows viewing ev ents stored in the Web card’s history. T his history is gathered only when the Web card is installed an d communica ting properly with the device. The history is stored in descending chronological orde r; Pa ge 1 Item 1 contains th e most recent event.
Support Informa tion 39 9.0 S UPPORT I NFORMATION Support data includes identi fying information for the Web c ard, as well as events and parameters available for the Liebert equipment.
Support Informa tion 40 9.2 Event s and Parameters You may view a list of all support ed events and parameters for the Liebert equipment through any interface.
Introd uction A1 A PPENDIX A-F IRMWARE U P DATES A.1 I NTRODUCTION Liebert’s Inte lliSlot ® cards may be updated to ta ke advantage of the latest release of the firmware with enhanced features, compatibil ity with new units or service pat ches. Upgraded firmware may be downloaded with a browser, su ch as Internet Expl orer.
Connect to the Card - Terminal Emulation, T elnet or Web Interface A2 A.2 C ONNECT TO THE C ARD - T ERMINAL E MULATION , T ELNET OR W EB I NTERFACE Upgrading the fi rmware requires connecting to the card with one of these interfaces.
Preparing to Update Li ebert IntelliS lot Firmware A3 A.2.3 Open the T elnet Interface To connect to the card using Telnet: 1. Open a Telnet connection on a computer with an Ethernet c onnection to t he Liebert unit. To do this: • Open a command prompt window—click the Start button, then Run .
Preparing to Update Li ebert IntelliS lot Firmware A4 A.3.2 Determine the Liebert IntelliSlot Card T ype and Firmware V ers ion Each type of Liebert IntelliSlot ca rd uses differ ent firmware. A ttemp ting to upgrade a card with the firmware for another type of card will fa il an d may damage the card.
Updating the Firmware - HTTP (W eb) Method A5 A.3.4 Choose a Method to Inst all the Firmware Upgrade To install the firmware up grade, ch oose one o f these three methods and refer to the as sociated step- by-step directions: • HTTP (Web) - see A.4 - Updating the Firmware - HTTP (Web) Method • TFTP - see A.
Updating the Firmware - TFTP (Hyp erTerminal, T elnet, W eb) Method A6 A.5 U P DATING THE F IRMW ARE - TFTP (H YPER T ERMINAL , T ELNET , W EB ) M ETHOD Follow these steps to update the firmware using the TFTP method. This method is available through the terminal emulation, Telnet an d Web interfaces with an Ethernet connection to the Web card.
Updating the Firmware - TFTP (Hyp erTerminal, T elnet, W eb) Method A7 Begin the Upgrade Process 11. When ready to begin the update, choose Initiate TFTP Firmware Update . 12. Open the TFTP application and start TFTP. Ensure that all settings are ready to transfer the fi le, includ ing the location of the upgrade file.
Updating the Firmware - TFTP (Hyp erTerminal, T elnet, W eb) Method A8 Specify TFTP Serve r and Upgrade Filename 4. Click the Edit button in the right pan el. 5. Select options as needed and refer to th e following guide to change any settings. 6. After making changes, click Save , then click Reinitiali ze in the left panel to reboot the card.
Updating the Firmware - Xmodem (Ser ial) Method A9 11. During the update, the wi ndow displays a progress bar, as shown below left. After the firmware update is comp leted, the card will reinit iali ze automatically. A reboot mes- sage, as shown below right, remains until the rebooting is finished.
Updating the Firmware - Xmodem (Ser ial) Method A10 Connect a Cable to the Serial Port s 1. Connect one end of a DB-9 null modem or file tran sfer cable to the Web card ’s serial port and the other to the computer’s serial port. The correct ca ble will have at a minimum, Pins 2 and 3 crossed at the ends, as shown in Figure A1 .
Updating the Firmware - Xmodem (Ser ial) Method A1 1 Download the First Firmware Up date File 12. After changing the communication rate to 1 15200 bps, press Enter to resume the firmware update. After you press Enter, HyperTerminal displays C s as it counts down the time remaining to locate and begin transferring the upgrade f iles.
Updating the Firmware - Xmodem (Ser ial) Method A12 Complete the Upgrade and Restore Communic ation Rate 22. Choose 9600 bps from the menu, shown below left. 23. From the HyperTerminal menu, cli ck on Call , then choose Disconnect (this will not close the HyperTerminal connection to the card).
Updating the Firmware - Xmodem (Ser ial) Method A13 Notes.
Updating the Firmware - Xmodem (Ser ial) Method A14.
.
Ensuring The Hi gh Av aila bilit y Of Mission-Critic al Dat a And App lic ations. Emerson Net work P ower , the global leader in enabling business-critical continuity , ensures network re siliency and.
Ein wichtiger Punkt beim Kauf des Geräts Emerson Liebert IntelliSlot IS-WEB485ADPT (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Emerson Liebert IntelliSlot IS-WEB485ADPT noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Emerson Liebert IntelliSlot IS-WEB485ADPT - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Emerson Liebert IntelliSlot IS-WEB485ADPT reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Emerson Liebert IntelliSlot IS-WEB485ADPT erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Emerson Liebert IntelliSlot IS-WEB485ADPT besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Emerson Liebert IntelliSlot IS-WEB485ADPT verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Emerson Liebert IntelliSlot IS-WEB485ADPT. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Emerson Liebert IntelliSlot IS-WEB485ADPT gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
